BS ISO 7391-2 : 1996 AMD 10746
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
Superseded date
07-15-2000
Published date
11-23-2012
Publisher
Defines methods for preparing test specimens and methods of testing for use in determination of the properties of polycarbonabte moulding and extrusion materials. Also states requirements for handling test material and conditioning both test material prior to moulding and specimens prior to testing.
| Committee |
PRI/82
|
| DevelopmentNote |
Superseded and renumbered by BS EN ISO 7391-2 (06/2000) Supersedes 95/123277 DC (06/2005)
|
| DocumentType |
Standard
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 7391-2:2006 | Identical |
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| ISO 75-1:2013 | Plastics Determination of temperature of deflection under load Part 1: General test method |
| EN ISO 62:2008 | Plastics - Determination of water absorption (ISO 62:2008) |
| EN ISO 10350 : 1995 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA |
| ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| EN ISO 180:2000/A2:2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013) |
| IEC 60250:1969 | Recommended methods for the determination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN ISO 75-1:2013 | Plastics - Determination of temperature of deflection under load - Part 1: General test method (ISO 75-1:2013) |
| EN ISO 178:2010/A1:2013 | PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013) |
| ISO 10350:1993 | Plastics Acquisition and presentation of comparable single-point data |
| EN ISO 2818:1996 | PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
| EN ISO 7391-1:2006 | Plastics - Polycarbonate (PC) moulding and extrusion materials - Part 1: Designation system and basis for specifications (ISO 7391-1:2006) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| EN ISO 75-2:2013 | Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013) |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| IEC 60296:2012 RLV | Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| EN ISO 3167:2014 | Plastics - Multipurpose test specimens (ISO 3167:2014) |
| IEC 60093:1980 | Methods of test for volume resistivity and surface resistivity of solid electrical insulating materials |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| ISO 1210:1992 | Plastics — Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source |
| EN ISO 179 : 1996 | PLASTICS - DETERMINATION OF CHARPY IMPACT STRENGTH |
| ISO 291:2008 | Plastics Standard atmospheres for conditioning and testing |
| EN ISO 4589-2:2017 | Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambient-temperature test (ISO 4589-2:2017) |
| ISO 62:2008 | Plastics Determination of water absorption |
| ISO 7391-1:2006 | Plastics Polycarbonate (PC) moulding and extrusion materials Part 1: Designation system and basis for specifications |
| ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
| EN ISO 291:2008 | Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) |
| ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
| ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
| ISO 179:1993 | Plastics Determination of Charpy impact strength |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 1628-4:1999 | Plastics — Determination of the viscosity of polymers in dilute solution using capillary viscometers — Part 4: Polycarbonate (PC) moulding and extrusion materials |
| ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
| EN ISO 1133:2005 | PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS |
| ISO 178:2010 | Plastics Determination of flexural properties |
| EN ISO 306:2013 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
| ISO 1133:2005 | Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics |
| IEC 61006:2004 | Electrical insulating materials - Methods of test for the determination of the glass transition temperature |
| ISO 527-1:2012 | Plastics Determination of tensile properties Part 1: General principles |
| EN ISO 294-1:2017 | Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017) |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.