• There are no items in your cart

BS ISO 8085-3:2001

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels. Metric series. Specifications Electrofusion fittings
Available format(s)

Hardcopy , PDF

Superseded date

01-31-2014

Language(s)

English

Published date

06-29-2007

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Material
6 General requirements
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Technical file
11 Marking
12 Packaging
Annex A (informative) Examples of typical connector sockets
        for electrofusion fittings
Annex B (normative) Formulae for calculating the equivalent
        dimensions of non-metric fitting series
Annex C (normative) Short-term pressure test method
Annex D (normative) Tensile test for fitting/pipe assemblies
Bibliography

Gives the requirements for polyethylene electrofusion fittings intended to be used with PE pipes and fittings for the supply of gaseous fuels.

Committee
PRI/88
DevelopmentNote
Supersedes 00/122205 DC (12/2001)
DocumentType
Standard
Pages
32
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 8085-3:2001 Identical

EN 682:2002/A1:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR SEALS USED IN PIPES AND FITTINGS CARRYING GAS AND HYDROCARBON FLUIDS
ISO 8085-2:2001 Polyethylene fittings for use with polyethylene pipes for the supply of gaseous fuels Metric series Specifications Part 2: Spigot fittings for butt fusion, for socket fusion using heated tools and for use with electrofusion fittings
ISO 6964:1986 Polyolefin pipes and fittings Determination of carbon black content by calcination and pyrolysis Test method and basic specification
ISO 13477:2008 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
ISO 3:1973 Preferred numbers Series of preferred numbers
ISO 18553:2002 Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds
ISO/TS 10839:2000 Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
ISO 13957:1997 Plastics pipes and fittings Polyethylene (PE) tapping tees Test method for impact resistance
ISO 13479:2009 Polyolefin pipes for the conveyance of fluids Determination of resistance to crack propagation Test method for slow crack growth on notched pipes
IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
ISO 12176-2:2008 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion
ISO 12162:2009 Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
ISO 13478:2007 Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ASTM D 4019 : 1994 : REV A Standard Test Method for Moisture in Plastics by Coulometric Regeneration of Phosphorus Pentoxide (Withdrawn 2002)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 13954:1997 Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
ISO 9356:1989 Polyolefin pipe assemblies with or without jointed fittings Resistance to internal pressure Test method
ISO 13955:1997 Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
ISO/TR 10837:1991 Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings
ISO 1872-1:1993 Plastics Polyethylene (PE) moulding and extrusion materials Part 1: Designation system and basis for specifications
ISO 497:1973 Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
EN 12117:1997 Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships
ISO 11413:2008 Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
ISO 13951:2015 Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
ISO 4437:2007 Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications

View more information
US$237.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.