|
ISO 1328-2:1997
|
Cylindrical gears ISO system of accuracy Part 2: Definitions and allowable values of deviations relevant to radial composite deviations and runout information
|
|
ISO/TR 13593:1999
|
Enclosed gear drives for industrial applications
|
|
ISO 6336-2:2006
|
Calculation of load capacity of spur and helical gears Part 2: Calculation of surface durability (pitting)
|
|
AGMA 6025 : D
|
SOUND FOR ENCLOSED HELICAL, HERRINGBONE AND SPIRAL BEVEL GEAR DRIVES
|
|
AGMA 2101 : D
|
FUNDAMENTAL RATING FACTORS AND CALCULATION METHODS FOR INVOLUTE SPUR AND HELICAL GEAR TEETH (METRIC EDITION)
|
|
AGMA 1010 : E
|
APPEARANCE OF GEAR TEETH - TERMINOLOGY OF WEAR AND FAILURE
|
|
ISO 14104:2017
|
Gears — Surface temper etch inspection after grinding, chemical method
|
|
ISO 1328-1:2013
|
Cylindrical gears — ISO system of flank tolerance classification — Part 1: Definitions and allowable values of deviations relevant to flanks of gear teeth
|
|
SAE J 1165 : 1986
|
REPORTING CLEANLINESS LEVELS OF HYDRAULIC FLUIDS
|
|
ISO 8579-2:1993
|
Acceptance code for gears Part 2: Determination of mechanical vibrations of gear units during acceptance testing
|
|
ISO/TR 13989-1:2000
|
Calculation of scuffing load capacity of cylindrical, bevel and hypoid gears Part 1: Flash temperature method
|
|
DIN 7190:2001-02
|
INTERFERENCE FITS - CALCULATION AND DESIGN RULES
|
|
ISO 6336-3:2006
|
Calculation of load capacity of spur and helical gears Part 3: Calculation of tooth bending strength
|
|
SAE AMS 2301 : 2015
|
STEEL CLEANLINESS, AIRCRAFT QUALITY MAGNETIC PARTICLE INSPECTION PROCEDURE
|
|
AGMA 6001 : D
|
DESIGN AND SELECTION OF COMPONENTS FOR ENCLOSED GEAR DRIVES
|
|
ISO 281:2007
|
Rolling bearings Dynamic load ratings and rating life
|
|
ISO 6336-5:2016
|
Calculation of load capacity of spur and helical gears Part 5: Strength and quality of materials
|
|
ISO/TR 10064-3:1996
|
Code of inspection practice Part 3: Recommendations relative to gear blanks, shaft centre distance and parallelism of axes
|
|
ISO/TR 10064-2:1996
|
Code of inspection practice Part 2: Inspection related to radial composite deviations, runout, tooth thickness and backlash
|
|
AGMA 913 : A
|
METHOD FOR SPECIFYING THE GEOMETRY OF SPUR AND HELICAL GEARS
|
|
AGMA 925 : A
|
EFFECT OF LUBRICATION ON GEAR SURFACE DISTRESS
|
|
ASTM D 341 : 2017 : REDLINE
|
Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products
|
|
ISO/R 773:1969
|
Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres)
|
|
ISO/TR 14179-1:2001
|
Gears Thermal capacity Part 1: Rating gear drives with thermal equilibrium at 95 C sump temperature
|
|
AGMA 9005 : E
|
INDUSTRIAL GEAR LUBRICATION
|
|
ISO 6336-1:2006
|
Calculation of load capacity of spur and helical gears Part 1: Basic principles, introduction and general influence factors
|
|
AGMA 901 : A
|
A RATIONAL PROCEDURE FOR THE PRELIMINARY DESIGN OF MINIMUM VOLUME GEARS
|
|
ISO 16889:2008
|
Hydraulic fluid power Filters Multi-pass method for evaluating filtration performance of a filter element
|
|
ISO/TR 10064-4:1998
|
Code of inspection practice Part 4: Recommendations relative to surface texture and tooth contact pattern checking
|
|
ISO 8579-1:2002
|
Acceptance code for gear units — Part 1: Test code for airborne sound
|
|
AGMA 2004 : C
|
GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL
|
|
IEC 61400-1:2005+AMD1:2010 CSV
|
Wind turbines - Part 1: Design requirements
|
|
ISO/TR 10064-1:2017
|
Code of inspection practice Part 1: Measurement of cylindrical gear tooth flanks
|
|
ISO 76:2006
|
Rolling bearings Static load ratings
|
|
AGMA 1012 : 2005
|
GEAR NOMENCLATURE, DEFINITIONS OF TERMS WITH SYMBOLS
|
|
ASTM D 1744 : 2013
|
Standard Test Method for Determination of Water in Liquid Petroleum Products by Karl Fischer Reagent (Withdrawn 2016)
|
|
ASTM A 534 : 2017 : REDLINE
|
Standard Specification for Carburizing Steels for Anti-Friction Bearings
|
Important note : All end users must be registered with an Account prior to user licenses being assigned.