• There are no items in your cart

PD CEN/TR 15858:2009

Current
Current

The latest, up-to-date edition.

Construction products. Assessment of the release of regulated dangerous substances from construction products based on the WT, WFT/FT procedures
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

04-30-2009

Executive summary
Foreword
1 Introduction
2 Scope
3 Terms and definitions
4 General procedure
5 Basic principles
   5.1 Introduction
   5.2 Construction Product Directive
   5.3 Scope of Mandate M/366
   5.4 Constituents, materials, products
   5.5 Regulations and Directives placing requirements
       on the environment
   5.6 Regulatory levels, RDS classes and sets of RDS
       classes
   5.7 Assessment procedures
   5.8 Combining construction products into a single
       assessment
   5.9 Construction Products covered by Member State
       Regulations but not covered under CPD-ETS
6 Release/emission scenarios
7 Identification of relevant regulated dangerous substances
8 Setting of RDS classes by Product TCs
9 Initial Type Assessment
10 Conformity to a class limit on the basis of a WT procedure
   10.1 General
   10.2 Dossier of information
   10.3 Assessment of the dossier
   10.4 Application of the WT procedure
11 Evaluation of conformity
12 Factory production control of RDSs
   12.1 General
   12.2 Routine control of production
13 Recommended delivery of the proposed system
   13.1 List of mandated RDSs
   13.2 Statistical basis for the system
   13.3 RDS classes and sets of RDS classes
   13.4 WT procedure
   13.5 WFT procedure
   13.6 FT procedure
   13.7 Evaluation of conformity
Annex A (informative) - Implementation of the proposed system
        by a manufacturer of a product
References

Specifies a procedure for assessing construction products with regards to their release/emission of regulated dangerous substances (RDS) into the environment in accordance with Essential Requirement Number 3 of the Construction Products Directive (CPD), as far as these construction products fall under the responsibility of CEN.

This CEN Technical Report describes a procedure for assessing construction products with regards to their release/emission of regulated dangerous substances (RDS) into the environment in accordance with Essential Requirement Number 3 of the Construction Products Directive (CPD), as far as these construction products fall under the responsibility of CEN. NOTE 1 For the purpose of this document and mandate M/366, the release of regulated dangerous substances from construction products is limited to two main environmental compartments: 1) soil, groundwater and surface water; 2) indoor air. NOTE 2 It should be noted that construction products falling under the CPD and these environmental compartments are the subject of other European Union regulations, e.g. REACH, and they may also be the subject of Member State regulations. This Technical Report defines how the mandated characteristics expressed in terms of mandated RDSs for each construction product can be assessed by an individual manufacturer using the ‘Without Testing’ (WT) procedure and/or the ‘Without Further Testing’ (WFT) and ‘Further Testing’ (FT) procedures after an initial type assessment and how the corresponding information accompanying the CE marking can be expressed in terms of declared values or RDS classes. This report describes: a) under which conditions a RDS class for a construction product may be declared by the individual manufacturer using the ‘Without Testing (WT)’ assessment procedure; b) if all relevant mandated RDSs are assessed by this Without Testing procedure, how a set of RDS classes for a construction product may also be declared by the manufacturer without the need for testing of their specific products; c) how to establish RDS classes for a construction product using a Without Further Testing procedure once sufficient information has been obtained from initial type testing; d) when and how to undertake Further Testing as part of factory production control

Committee
B/557
DocumentType
Standard
Pages
40
PublisherName
British Standards Institution
Status
Current

Standards Relationship
CEN/TR 15858:2009 Identical

BS PAS 8401(2014) : 2014 IMPLEMENTING AN INSIDE SALES MANAGEMENT METHODOLOGY - GUIDE

89/106/EEC : 1988 COUNCIL DIRECTIVE OF 21 DECEMBER 1988 ON THE APPROXIMATION OF LAWS, REGULATIONS AND ADMINISTRATIVE PROVISIONS OF THE MEMBER STATES RELATING TO CONSTRUCTION PRODUCTS

View more information
US$261.13
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.