• There are no items in your cart

PD CEN/TS 14541:2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics pipes and fittings. Characteristics for utilisation of non-virgin PVC-U, PP and PE materials
Available format(s)

Hardcopy , PDF

Superseded date

08-04-2022

Language(s)

English

Published date

05-31-2013

Foreword
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 Utilisation of non-virgin material for non-pressure application
5 Utilisation of non-virgin material for pressure application
6 General guidance for utilisation of non-virgin material
Bibliography

Defines definitions and recommended characteristics and test methods for the utilisation of PVC-U, PP and PE non-virgin materials in pipes, fittings and ancillaries for both pressure and non-pressure piping systems.

This Technical Specification specifies definitions and recommended characteristics and test methods for the utilisation of PVC U, PP and PE non-virgin materials in pipes, fittings and ancillaries for both pressure and non-pressure piping systems. This Technical Specification specifies the conditions for utilisation of non-virgin material with and without agreed specification Non-virgin materials may be reformulated by the use of additives and processing techniques to meet an agreed specification. Typically the additives used would be stabilisers and pigments etc. The WG responsible for the product standard should consider the content of this document and only permit dosage levels which give compliance with the requirements of the product standard. Further, the WG should consider whether extra or more frequent product testing is relevant when using such material in the production of pipes and fittings in accordance with the relevant product standard. NOTE For the purpose of this specification the term pipes means extruded pipes, gutters and any parts of a fabricated fitting which is made from an extruded pipe. The term fitting means injection- and rotomoulded fittings and injection moulded parts of a fabricated fitting. For the recycling process, the testing and the use of the non-virgin material National and/or European regulations may apply.

Committee
PRI/88/1
DevelopmentNote
Supersedes DD CEN/TS 14541. (05/2013) Reviewed and confirmed by BSI, February 2017. (02/2017)
DocumentType
Standard
Pages
14
PublisherName
British Standards Institution
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Standards Relationship
CEN/TS 14541:2013 Identical

EN ISO 13229:2011 Thermoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229:2010)
ISO 3451-1:2008 Plastics Determination of ash Part 1: General methods
ISO 13229:2010 Thermoplastics piping systems for non-pressure applications Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings Determination of the viscosity number and K-value
EN 15345:2007 Plastics - Recycled Plastics - Characterisation of Polypropylene (PP) recyclates
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
EN ISO 3451-1:2008 Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008)
EN 15346:2014 Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates
EN ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
EN ISO 3451-5:2002 Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5:2002)
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
EN 10204:2004 Metallic products - Types of inspection documents
ISO 9001:2015 Quality management systems — Requirements
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 3451-5:2002 Plastics — Determination of ash — Part 5: Poly(vinyl chloride)
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
EN 15344:2007 Plastics - Recycled Plastics - Characterisation of Polyethylene (PE) recyclates
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
EN ISO 306:2013 Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013)
EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD

View more information
US$134.16
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.