PD ISO/TR 10017:2003
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
07-20-2021
English
06-19-2003
1 Scope
2 Terms and definitions
3 Identification of potential needs for statistical
techniques
4 Descriptions of statistical techniques identified
4.1 General
4.2 Descriptive statistics
4.3 Design of experiments
4.4 Hypothesis testing
4.5 Measurement analysis
4.6 Process capability analysis
4.7 Regression analysis
4.8 Reliability analysis
4.9 Sampling
4.10 Simulation
4.11 SPC charts (Statistical Process Control
charts)
4.12 Statistical tolerancing
4.13 Time series analysis
Annex A Overview of statistical techniques that could be
used to support the requirements of clauses of
ISO 9001
Bibliography
Gives guidance for selecting appropriate statistical techniques of possible use to an organization for development, implementation or maintenance of a quality system to comply with ISO 9001. This is achieved by examination of the requirements of ISO 9001 involving use of quantitative data, followed by identification and description of those statistical techniques useful when applied to such data.
| Committee |
QS/1
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO/TR 10017:2003 | Identical |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| ISO 5725-1:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 1: General principles and definitions |
| ISO 11843-2:2000 | Capability of detection — Part 2: Methodology in the linear calibration case |
| IEC 61123:1991 | Reliability testing - Compliance test plans for success ratio |
| ISO 2859-4:2002 | Sampling procedures for inspection by attributes Part 4: Procedures for assessment of declared quality levels |
| ISO 10725:2000 | Acceptance sampling plans and procedures for the inspection of bulk materials |
| IEC 60863:1986 | Presentation of reliability, maintainability and availability predictions |
| ISO 2859-3:2005 | Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures |
| ISO/TS 14253-2:1999 | Geometrical Product Specifications (GPS) Inspection by measurement of workpieces and measuring equipment Part 2: Guide to the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| ISO 11843-1:1997 | Capability of detection Part 1: Terms and definitions |
| ISO 7873:1993 | Control charts for arithmetic average with warning limits |
| ISO 2854:1976 | Statistical interpretation of data — Techniques of estimation and tests relating to means and variances |
| ISO 16269-7:2001 | Statistical interpretation of data — Part 7: Median — Estimation and confidence intervals |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| ISO 3951:1989 | Sampling procedures and charts for inspection by variables for percent nonconforming |
| IEC 61649:2008 | Weibull analysis |
| IEC 61014:2003 | Programmes for reliability growth |
| ISO/IEC Guide 43-1:1997 | Proficiency testing by interlaboratory comparisons Part 1: Development and operation of proficiency testing schemes |
| IEC 61070:1991 | Compliance test procedures for steady-state availability |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| IEC 61078:2016 | Reliability block diagrams |
| IEC 61165:2006 | Application of Markov techniques |
| ISO 7870:1993 | Control charts General guide and introduction |
| ISO 5725-3:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 3: Intermediate measures of the precision of a standard measurement method |
| ISO Guide 33:2015 | Reference materials Good practice in using reference materials |
| ISO 11648-2:2001 | Statistical aspects of sampling from bulk materials — Part 2: Sampling of particulate materials |
| ISO 2859-2:1985 | Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection |
| ISO 5725-6:1994 | Accuracy (trueness and precision) of measurement methods and results — Part 6: Use in practice of accuracy values |
| ISO Guide 35:2017 | Reference materials Guidance for characterization and assessment of homogeneity and stability |
| ISO 2859-0:1995 | Sampling procedures for inspection by attributes — Part 0: Introduction to the ISO 2859 attribute sampling system |
| IEC 61163-1:2006 | Reliability stress screening - Part 1: Repairable assemblies manufactured in lots |
| ISO 5725-4:1994 | Accuracy (trueness and precision) of measurement methods and results Part 4: Basic methods for the determination of the trueness of a standard measurement method |
| ISO 11095:1996 | Linear calibration using reference materials |
| ISO 2602:1980 | Statistical interpretation of test results Estimation of the mean Confidence interval |
| ISO 8422:2006 | Sequential sampling plans for inspection by attributes |
| IEC 61163-2:1998 | Reliability stress screening - Part 2: Electronic components |
| ISO 3301:1975 | Statistical interpretation of data — Comparison of two means in the case of paired observations |
| ISO 3534-2:2006 | Statistics Vocabulary and symbols Part 2: Applied statistics |
| IEC 61124:2012 | Reliability testing - Compliance tests for constant failure rate and constant failure intensity |
| ISO/TR 13425:2006 | Guidelines for the selection of statistical methods in standardization and specification |
| ISO 9004:2009 | Managing for the sustained success of an organization A quality management approach |
| ISO/TR 8550:1994 | Guide for the selection of an acceptance sampling system, scheme or plan for inspection of discrete items in lots |
| IEC 61164:2004 | Reliability growth - Statistical test and estimation methods |
| ISO 7966:1993 | Acceptance control charts |
| ISO 8423:2008 | Sequential sampling plans for inspection by variables for percent nonconforming (known standard deviation) |
| IEC 60300-1:2014 | Dependability management - Part 1: Guidance for management and application |
| ISO 3494:1976 | Statistical interpretation of data — Power of tests relating to means and variances |
| ISO 10012:2003 | Measurement management systems — Requirements for measurement processes and measuring equipment |
| ISO 5725-2:1994 | Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method |
| ISO 9001:2015 | Quality management systems — Requirements |
| IEC 60300-2:2004 | Dependability management - Part 2: Guidelines for dependability management |
| ISO 3534-3:2013 | Statistics — Vocabulary and symbols — Part 3: Design of experiments |
| IEC 60300-3-9:1995 | Dependability management - Part 3: Application guide - Section 9: Risk analysis of technological systems |
| ISO 5479:1997 | Statistical interpretation of data — Tests for departure from the normal distribution |
| ISO 9000:2015 | Quality management systems — Fundamentals and vocabulary |
| ISO 11462-1:2001 | Guidelines for implementation of statistical process control (SPC) Part 1: Elements of SPC |
| ISO 8595:1989 | Interpretation of statistical data Estimation of a median |
| IEC 61650:1997 | Reliability data analysis techniques - Procedures for comparison of two constant failure rates and two constant failure (event) intensities |
| ISO/IEC Guide 43-2:1997 | Proficiency testing by interlaboratory comparisons Part 2: Selection and use of proficiency testing schemes by laboratory accreditation bodies |
| ISO/TR 7871:1997 | Cumulative sum charts Guidance on quality control and data analysis using CUSUM techniques |
| ISO 5725-5:1998 | Accuracy (trueness and precision) of measurement methods and results — Part 5: Alternative methods for the determination of the precision of a standard measurement method |
| ISO 3534-1:2006 | Statistics — Vocabulary and symbols — Part 1: General statistical terms and terms used in probability |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.