Name: CGA C 14 : 2005(R2010)
Brand: CGA

CGA C 14 : 2005(R2010)

Withdrawn

PROCEDURES FOR FIRE TESTING OF DOT CYLINDER PRESSURE RELIEF DEVICE SYSTEMS

Withdrawn date

10-16-2023

Published date

01-12-2013

Publisher

Compressed Gas Association

1 Introduction
   1.1 United States
   1.2 Canada
   1.3 Testing conditions
2 Scope
3 Definitions
   3.1 Normally charged
   3.2 Cylinder orientation
   3.3 Full exposure to the fire
   3.4 Equipped as it would be for transportation and use
   3.5 Rupture
4 When fire testing is required
5 Selection of systems and methods for testing
6 Preparation of systems for testing
7 Chimney test method
   7.1 Equipment capabilities
   7.2 Typical apparatus
   7.3 Recording of design and performance characteristics
   7.4 Burn rates
   7.5 Insulation of exterior wall
   7.6 Design of apparatus
   7.7 Calibration of apparatus
   7.8 Monitoring temperatures
8 Wood bonfire test method
   8.1 Securing the cylinder
   8.2 Bonfire design
   8.3 Kerosene
   8.4 Wind shield
   8.5 Fire capabilities
9 Test procedure
10 Acceptance criteria for chimney and bonfire tests
11 References
Appendices
Appendix A - Burner and ignition system for chimney fire
             test (Normative)
Appendix B - Method B (Normative)
Appendices figures

Specifies a new set of test procedures and apparatus for fire testing of compressed gas cylinder safety (pressure) relief devices as required by DOT regulations, 49 CFR, Section 173.34(d). Applicable to cylinders which are less than 500 pounds internal water volume and are designed to provide a means of testing to DOT requirements anywhere, with reliable test data and repeatable test results.

DocumentType	Standard
PublisherName	Compressed Gas Association
Status	Withdrawn

11/30196123 DC : DRAFT MAY 2011	BS ISO 11119-2 - GAS CYLINDERS OF COMPOSITE CONSTRUCTION - SPECIFICATION AND TEST METHODS - PART 2: FULLY WRAPPED FIBRE REINFORCED COMPOSITE GAS CYLINDERS WITH LOAD-SHARING METAL LINERS
MIL-E-24269 Revision B:1988	EXTINGUISHER, FIRE, CARBON DIOXIDE, 15 POUND, PORTABLE, PERMANENT SHUTOFF, NAVY SHIPBOARD USE
10/30196141 DC : 0	BS ISO 11119-3 - GAS CYLINDERS OF COMPOSITE CONSTRUCTION - SPECIFICATION AND TEST METHODS - PART 3: FULLY WRAPPED FIBRE REINFORCED COMPOSITE GAS CYLINDERS AND TUBES WITH NON-METALLIC AND NON-LOAD SHARING METAL LINERS
ISO 11119-2:2012	Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 2: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450 l with load-sharing metal liners
DIN EN 14427:2014-09	LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
I.S. EN 14427:2014	LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
I.S. EN 12245:2009	TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
CGA S 1.3 : 2008	PRESSURE RELIEF DEVICE STANDARDS - PART 3: STATIONARY STORAGE CONTAINERS FOR COMPRESSED GASES
ISO 11119-3:2013	Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 3: Fully wrapped fibre reinforced composite gas cylinders and tubes up to 450L with non-load-sharing metallic or non-metallic liners
CGA S 1.1 : 2011	PRESSURE RELIEF DEVICE STANDARDS - PART 1: CYLINDERS FOR COMPRESSED GASES
DIN EN 12245:2012-03	Transportable gas cylinders - Fully wrapped composite cylinders (includes Amendment A1:2011)
BS EN 12257:2002	Transportable gas cylinders. Seamless, hoop-wrapped composite cylinders
DIN EN 14427 E : 2014	LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
UNI EN 14427 : 2014	LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE FULLY WRAPPED COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
UNI EN 12245 : 2011	TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
B342-15	Selection and use of UN pressure receptacles, multiple-element gas containers, and other pressure receptacles for the transport of dangerous goods, Class 2
11/30229997 DC : 0	BS EN 14427 - LPG EQUIPMENT AND ACCESSORIES - TRANSPORTABLE REFILLABLE COMPOSITE CYLINDERS FOR LPG - DESIGN AND CONSTRUCTION
B340-14	Selection and use of cylinders, spheres, tubes, and other containers for the transportation of dangerous goods, class 2
ISO 11119-1:2012	Gas cylinders Refillable composite gas cylinders and tubes Design, construction and testing Part 1: Hoop wrapped fibre reinforced composite gas cylinders and tubes up to 450 l
BS EN 14427:2014	LPG equipment and accessories. Transportable refillable fully wrapped composite cylinders for LPG. Design and construction
UNE-EN 14427:2014	LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
UNE-EN 12245:2009	Transportable gas cylinders - Fully wrapped composite cylinders
EN 14427:2014	LPG equipment and accessories - Transportable refillable fully wrapped composite cylinders for LPG - Design and construction
EN 12245:2009+A1:2011	Transportable gas cylinders - Fully wrapped composite cylinders
CGA S 1.2 : 2009	PRESSURE RELIEF DEVICE STANDARDS - PART 2: PORTABLE CONTAINERS FOR COMPRESSED GASES
CGA C 12 : 2014	QUALIFICATION PROCEDURE FOR ACETYLENE CYLINDER DESIGN
EN 12257:2002	Transportable gas cylinders - Seamless, hoop-wrapped composite cylinders

CGA C 12 : 2014	QUALIFICATION PROCEDURE FOR ACETYLENE CYLINDER DESIGN
CGA C 15 : 2014	PROCEDURES FOR CYLINDER DESIGN PROOF AND SERVICE PERFORMANCE TESTS
CGA S 1.2 : 2009	PRESSURE RELIEF DEVICE STANDARDS - PART 2: PORTABLE CONTAINERS FOR COMPRESSED GASES
CGA S 1.3 : 2008	PRESSURE RELIEF DEVICE STANDARDS - PART 3: STATIONARY STORAGE CONTAINERS FOR COMPRESSED GASES
CGA S 1.1 : 2011	PRESSURE RELIEF DEVICE STANDARDS - PART 1: CYLINDERS FOR COMPRESSED GASES