• There are no items in your cart

CSA C61400-3 : 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

WIND TURBINES - PART 3: DESIGN REQUIREMENTS FOR OFFSHORE WIND TURBINES
Available format(s)

Hardcopy , PDF

Superseded date

02-28-2016

Language(s)

English

Published date

01-01-2016

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Principal elements
6 External conditions
7 Structural design
8 Control and protection system
9 Mechanical systems
10 Electrical system
11 Foundation design
12 Assessment of the external conditions at an offshore
   wind turbine site
13 Assembly, installation and erection
14 Commissioning, operation and maintenance
Annex A (informative) - Key design parameters for an
        offshore wind turbine
Annex B (informative) - Wave spectrum formulations
Annex C (informative) - Shallow water hydrodynamics
        and breaking waves
Annex D (informative) - Guidance on calculation of
        hydrodynamic loads
Annex E (informative) - Recommendations for design of
        offshore wind turbine support structures with
        respect to ice loads
Annex F (informative) - Offshore wind turbine foundation
        design
Annex G (informative) - Statistical extrapolation of
        operational metocean parameters for ultimate
        strength analysis
Annex H (informative) - Corrosion protection
Bibliography

Describes additional requirements for assessment of the external conditions at an offshore wind turbine site and also specifies essential design requirements to ensure the engineering integrity of offshore wind turbines.

DocumentType
Standard
Pages
306
ProductNote
Reconfirmed EN
PublisherName
Canadian Standards Association
Status
Superseded
SupersededBy

IEC 61000-6-4:2006+AMD1:2010 CSV ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS
ISO 19901-6:2009 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 6: Marine operations
IEC 60898:1995 Electrical accessories - Circuit-breakers for overcurrent protection for household and similar installations
ISO 3010:2017 Bases for design of structures — Seismic actions on structures
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
CSA C61400-1 : 2014 WIND TURBINES - PART 1: DESIGN REQUIREMENTS
IEC 61000-6-2:2016 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity standard for industrial environments
IEC 61400-24:2010 Wind turbines - Part 24: Lightning protection
ISO 4354:2009 Wind actions on structures
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 2394:2015 General principles on reliability for structures
IEC 61000-6-1 : 3.0 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS
IEC 60204-11:2000 Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
IEC TS 61400-13:2001 Wind turbine generator systems - Part 13: Measurement of mechanical loads
ISO 2533:1975 Standard Atmosphere
ISO 17776:2016 Petroleum and natural gas industries Offshore production installations Major accident hazard management during the design of new installations
ISO 15544:2000 Petroleum and natural gas industries — Offshore production installations — Requirements and guidelines for emergency response
NACE RP 01 76 : 2003 CORROSION CONTROL OF STEEL FIXED OFFSHORE STRUCTURES ASSOCIATED WITH PETROLEUM PRODUCTION
API 2A : 1986 RECOMMENDED PRACTICE FOR PLANNING, DESIGNING AND CONSTRUCTING FIXED OFFSHORE PLATFORMS
ISO 13819-2:1995 Petroleum and natural gas industries Offshore structures Part 2: Fixed steel structures
IEC 60721-2-1:2013 Classification of environmental conditions - Part 2-1: Environmental conditions appearing in nature - Temperature and humidity
CSA ISO 19901-1 : 2016 PETROLEUM AND NATURAL GAS INDUSTRIES - SPECIFIC REQUIREMENTS FOR OFFSHORE STRUCTURES - PART 1: METOCEAN DESIGN AND OPERATING CONSIDERATIONS
ISO 19906:2010 Petroleum and natural gas industries Arctic offshore structures
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60755:2017 General safety requirements for residual current operated protective devices
IEC 61000-6-1:2016 Electromagnetic compatibility (EMC) - Part 6-1: Generic standards - Immunity standard for residential, commercial and light-industrial environments
ISO 9001:2015 Quality management systems — Requirements
STG 2215 : 1998 RICHTLINIEN FUER KORROSIONSSCHUTZ FUER SCHIFFE UND SEEBAUWERKE - TEIL 1: "SCHIFF, SEEBAUWERK UND AUSRUESTUNG - NEUBAU"
IEC 61000-6-4:2006+AMD1:2010 CSV Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
ISO 8930:1987 General principles on reliability for structures List of equivalent terms
CSA ISO 9001 : 2016 QUALITY MANAGEMENT SYSTEMS - REQUIREMENTS
IEC 62305-4:2010 Protection against lightning - Part 4: Electrical and electronic systems within structures
IEC 61310-1:2007 Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals
IEC 60173:1964 Colours of the cores of flexible cables and cords
CSA ISO 19900 : 2014 PETROLEUM AND NATURAL GAS INDUSTRIES - GENERAL REQUIREMENTS FOR OFFSHORE STRUCTURES
IEC 61000-6-2 : 3.0:2016 ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
CAN/CSA-ISO 19901-4:17 Petroleum and natural gas industries — Specific requirements for offshore structures — Part 4: Geotechnical and foundation design considerations (Adopted ISO 19901-4:2016, second edition, 2016-07-15)
S6-14 Canadian Highway Bridge Design Code
IEC 62305-3:2010 Protection against lightning - Part 3: Physical damage to structures and life hazard
NORSOK M 501 : REV 6 SURFACE PREPARATION AND PROTECTIVE COATING
IEC 61400-21:2008 Wind turbines - Part 21: Measurement and assessment of power quality characteristics of grid connected wind turbines

View more information

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.