CSA NGV 5.1 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
11-25-2020
English
01-01-2016
Preface
1 Scope
2 Reference publications
3 Definitions
4 General construction and assembly
5 Flow rate
6 General design requirements
7 Marking
8 General testing requirements
9 Additional requirements
10 Quality assurance plan
11 Installation
Annex A (normative) - Items unique to Canada
Annex B (informative) - Compressibility factors (Brill-Begs
correlation for the compressibility factor)
Annex C (informative) - Wire color designations
Describes mechanical, physical, and electrical requirements for a newly manufactured appliance that dispenses natural gas for vehicles directly into the vehicle natural gas fuel storage system, referred to as a residential fueling appliance (RFA).
| DevelopmentNote |
Effective in Canada November 1, 2017. (06/2016)
|
| DocumentType |
Standard
|
| Pages |
79
|
| PublisherName |
Canadian Standards Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| NFPA 54 : 2018 | NATIONAL FUEL GAS CODE |
| ANSI Z223.1 : 2018 | NATIONAL FUEL GAS CODE |
| CSA/ANSI NGV 4.1-2018 | Natural gas vehicle (NGV) dispensing systems |
| NFPA 52 : 2016 | VEHICULAR NATURAL GAS FUEL SYSTEMS CODE |
| IEC 61025:2006 | Fault tree analysis (FTA) |
| CSA NGV1 : 2017 | COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES |
| SAE J 200 : 2015 | CLASSIFICATION SYSTEM FOR RUBBER MATERIALS |
| ASME B18.2.1 : 2012 | SQUARE, HEX, HEAVY HEX, AND ASKEW HEAD BOLTS AND HEX, HEAVY HEX, HEX FLANGE, LOBED HEAD, AND LAG SCREWS (INCH SERIES) |
| ANSI Z21.21 : 2015 | AUTOMATIC VALVES FOR GAS APPLIANCES |
| UL 514A:11ED 2013-02 | Metallic Outlet Boxes |
| ANSI NGV1 : 2017 | COMPRESSED NATURAL GAS VEHICLE (NGV) FUELING CONNECTION DEVICES |
| ANSI/CSA NGV 4.2-2014 (R2019)/CSA 12.52-2014 (R2018) | Hoses for natural gas dispensing systems |
| C22.1-15 | Canadian Electrical Code, Part I (23rd Edition), Safety Standard for Electrical Installations |
| CSA B51 : 2014 | BOILER, PRESSURE VESSEL, AND PRESSURE PIPING CODE |
| IEC 60812:2006 | Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA) |
| CSA C22.2 No. 77 : 2014 | MOTORS WITH INHERENT OVERHEATING PROTECTION |
| CSA 6.5 : 2015 | AUTOMATIC VALVES FOR GAS APPLIANCES |
| SAE J 102 : 1992 | SQUARE HEAD SETSCREWS |
| ASME B18.6.4 : 1998 | THREAD FORMING AND THREAD CUTTING TAPPING SCREWS AND METALLIC DRIVE SCREWS, INCH SERIES |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| CSA C22.2 No. 0.4 : 2004(R2013) | BONDING OF ELECTRICAL EQUIPMENT |
| CSA C22.2 No. 0.5 : 2016 | THREADED CONDUIT ENTRIES |
| NFPA 79 : 2015 | ELECTRICAL STANDARD FOR INDUSTRIAL MACHINERY |
| CSA C22.2 No. 24 : 2015 | TEMPERATURE-INDICATING AND -REGULATING EQUIPMENT |
| ANSI NGV3.1 : 2014 | FUEL SYSTEM COMPONENTS FOR COMPRESSED NATURAL GAS POWERED VEHICLES |
| UL 795:8ED 2016-12 | Commercial-Industrial Gas Heating Equipment |
| CSA C22.2 No. 139 : 2013 | ELECTRICALLY OPERATED VALVES |
| ASME B40.100 : 2013 | Pressure Gauges and Gauge Attachments (B40.100 - 2013) |
| CSA 12.3 : 2014 | FUEL SYSTEM COMPONENTS FOR COMPRESSED NATURAL GAS POWERED VEHICLES |
| ASME B18.6.2 : 1998 | SLOTTED HEAD CAP SCREWS, SQAURE HEAD SET SCREWS, AND SLOTTED HEADLESS SET SCREWS (INCH SERIES) |
| IEEE/ASTM SI_10-2010 | American National Standard for Metric Practice |
| SAE J 1065 : 2016 | NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING |
| CSA 12.56 : 1999 | MANUALLY OPERATED VALVES FOR NATURAL GAS DISPENSING SYSTEMS |
| SAE J 1739 : 2009 | POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA) |
| MIL-STD-882 Revision E:2012 | System Safety |
| NFPA 52 : 2016 | VEHICULAR NATURAL GAS FUEL SYSTEMS CODE |
| ASME B36.10M : 2015 | WELDED AND SEAMLESS WROUGHT STEEL PIPE |
| ASTM D 865 : 2011 | Standard Test Method for Rubber<char: emdash>Deterioration by Heating in Air (Test Tube Enclosure) |
| NFPA 70 : 2017 | NATIONAL ELECTRICAL CODE |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| SAE J 526 : 2016 | WELDED LOW-CARBON STEEL TUBING SUITABLE FOR BENDING, FLARING, BEADING, FORMING AND BRAZING |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| SAE J 525 : 2016 | WELDED AND COLD DRAWN LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| ASTM D 648 : 2016 | Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position |
| ASTM D 5420 : 2016 : REDLINE | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact) |
| CSA C22.2 No. 100 : 2014 | MOTORS AND GENERATORS |
| SAE J 1183 : 2017 | RECOMMENDED GUIDELINES FOR FATIGUE TESTING OF ELASTOMERIC MATERIALS AND COMPONENTS |
| SAE J 524 : 2016 | SEAMLESS LOW-CARBON STEEL TUBING ANNEALED FOR BENDING AND FLARING |
| UL 429:7ED 2013-11 | Electrically Operated Valves |
| CFR 49(PTS400-599) : 0 | TRANSPORTATION |
| ASME B18.2.2 : 2015 | NUTS FOR GENERAL APPLICATIONS: MACHINE SCREW NUTS, HEX, SQUARE, HEX FLANGE, AND COUPLING NUTS (INCH SERIES) |
| SAE J 105 : 1992 | HEX BOLTS |
| NFPA 54 : 2018 | NATIONAL FUEL GAS CODE |
| C22.2 NO. 236-15 | Heating and cooling equipment (Bi-national standard with UL 1995) |
| ASME PV CODE SET : 2017 | BOILER AND PRESSURE VESSEL CODE - COMPLETE SET |
| ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
| ANSI Z223.1 : 2018 | NATIONAL FUEL GAS CODE |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| UL 515:2ED 2015-07 | Standard for Electrical Resistance Trace Heating for Commercial Applications |
| SAE J 479 : 1992 | SLOTTED HEADLESS SETSCREWS |
| UL 60079-0:6ED 2013-07 | Explosive Atmospheres - Part 0: Equipment - General Requirements |
| SAE J 478 : A | SLOTTED AND RECESSED HEAD SCREWS |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
| ASME B18.6.3 : 2013 | MACHINE SCREWS, TAPPING SCREWS, AND METALLIC DRIVE SCREWS (INCH SERIES) |
| NFPA 497 : 2017 | CLASSIFICATION OF FLAMMABLE LIQUIDS, GASES, OR VAPORS AND OF HAZARDOUS (CLASSIFIED) LOCATIONS FOR ELECTRICAL INSTALLATIONS IN CHEMICAL PROCESS AREAS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.