• There are no items in your cart

DD IEC/TS 61800-8:2010

Current
Current

The latest, up-to-date edition.

Adjustable speed electrical power drive systems Specification of voltage on the power interface
Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

07-31-2010

FOREWORD
1 Scope
2 Normative references
3 Overview and terms and definitions
4 System approach
5 Line section
6 Input converter section
7 Output converter section (inverter section)
8 Filter section
9 Cabling section between converter output terminals
   and motor terminals
10 Calculation guidelines for the voltages on the power
   interface according to the section models
11 Installation and example
Annex A - (Different types of power supply systems)
Annex B - (Inverter Voltages)
Annex C - (Output Filter Performance)
Bibliography

Provides the guidelines for the determination of voltage on the power interface of power drive systems (PDS's).

This part of IEC61800 gives the guidelines for the determination of voltage on the power interface of power drive systems (PDS’s).

NOTE The power interface, as defined in the IEC61800 series, is the electrical connection used for the transmission of the electrical power between the converter and the motor(s) of the PDS.

The guidelines are established for the determination of the phase to phase voltages and the phase to ground voltages at the converter and at the motor terminals.

These guidelines are limited in the first issue of this document to the following topologies with three phase output

  • indirect converter of the voltage source type, with single phase diode rectifier as line side converter;

  • indirect converter of the voltage source type, with three phase diode rectifier as line side converter;

  • indirect converter of the voltage source type, with three phase active line side converter.

All specified inverters in this issue are of the pulse width modulation type, where the individual output voltage pulses are varied according to the actual demand of voltage versus time integral.

Other topologies are excluded of the scope of this International Specification.

Safety aspects are excluded from this Specification and are stated in IEC61800-5 series. EMC aspects are excluded from this Specification and are stated in IEC61800-3.

Committee
PEL/22
DevelopmentNote
Supersedes 08/30180328 DC. (09/2010)
DocumentType
Standard
Pages
68
PublisherName
British Standards Institution
Status
Current
Supersedes

Standards Relationship
IEC TS 61800-8:2010 Identical

IEC 61800-3:2017 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods
IEC 61800-2:2015 Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems
IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
IEC 61000-2-4:2002 Electromagnetic compatibility (EMC) - Part 2-4: Environment - Compatibility levels in industrial plants for low-frequency conducted disturbances
IEC 60364-4-41:2005+AMD1:2017 CSV Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock
IEC 60050-551:1998 International Electrotechnical Vocabulary (IEV) - Part 551: Power electronics
IEC TS 60034-18-42:2008 Rotating electrical machines - Part 18-42: Qualification and acceptance tests for partial discharge resistant electrical insulation systems (Type II) used in rotating electrical machines fed from voltage converters
IEC 60364-1:2005 Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions
IEC TS 60034-18-41:2006 Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
IEC 60034-18-1:2010 Rotating electrical machines - Part 18-1: Functional evaluation of insulation systems - General guidelines
IEC 60146-1-1:2009 Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements
IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
IEC TS 60034-17:2006 Rotating electrical machines - Part 17: Cage induction motors when fed from converters - Application guide
IEC 60146-2:1999 Semiconductor converters - Part 2: Self-commutated semiconductor converters including direct d.c. converters
IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
IEC 60050-521:2002 International Electrotechnical Vocabulary (IEV) - Part 521: Semiconductor devices and integrated circuits

View more information
US$311.44
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.