• There are no items in your cart

DEFSTAN 03-19/4(2010) : 2010

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by
withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

ELECTRO-DEPOSITION OF CADMIUM
Available format(s)

Hardcopy , PDF

Withdrawn date

05-21-2015

Language(s)

English

Published date

01-01-2010

Foreword
Introduction
1 Scope
2 Warning
3 Normative References
4 Definitions
5 Information to be Supplied to the Processor
6 Process Control
7 Pre-treatment and Preparation
8 Heat Treatment
9 Surface Preparation
10 Cadmium Plating
11 Washing
12 Passivation
13 Heat Treatment Relief of Hydrogen Embrittlement
14 Inspection
15 Selection of Test Samples
16 Visual
17 Adhesion
18 Thickness of
19 Freedom
20 Re-of items rejected on
Annex A - Composition Preparation of Suitable
Annex B - Method for the Detection of Mercury
Annex C - Adhesion Tests
Annex D - Methods for the Determination of Average
          Thickness

Defines the requirements for the electro-deposition of cadmium on non-corrosion resisting steel items for protection against corrosion, and on copper based alloy items and corrosion resisting steel items for the reduction of contact corrosion of less noble metallic materials.

DevelopmentNote
Supersedes DEFSTAN 03-19/3(2005). (01/2011) This standard is obsolescent because it is no longer required for the procurement of new equipment but is retained for maintenance purposes in support of existing in-service equipment. (05/2013)
DocumentType
Standard
Pages
18
PublisherName
UK Ministry of Defence Standards
Status
Withdrawn
SupersededBy
Supersedes

BS 6SP 4(2000) : 2000 AEROSPACE SERIES - PINS HEADED, PLAIN SHANK, DRILLED, STEEL ALLOY AND CORROSION RESISTING STEEL WITH A STRENGTH CLASS 880 MPA
SAE AMS 79-015 : 2017 COMPOUND, CLEANING GEL FOR AIRCRAFT SURFACES
BS 2A173(1962) : 1962 SPECIFICATION FOR 100 DEGREES COUNTERSUNK HEAD STEEL BOLTS (UNIFIED THREADS), CADMIUM PLATED, FOR AIRCRAFT
BS SP126 & SP127(1959) : 1959 WASHERS FOR UNIFIED HEXAGONS FOR AIRCRAFT (PRIMARILY FOR FACING PURPOSES)
BS SP122-125(1958) : 1958 WASHERS FOR UNIFIED HEXAGONS FOR AIRCRAFT (PRIMARILY FOR PACKING PURPOSES)
BS 7195(1989) : 1989 GUIDE FOR PREVENTION OF CORROSION OF METALS CAUSED BY VAPOURS FROM ORGANIC MATERIALS
ISO 9940:2015 Aerospace series Fluid, hydraulic, phosphate ester-base, fire resistant Technical specification
DEFSTAN 21-5/4(2016) : 2016 CODE OF PRACTICE FOR PROTECTIVE FINISHES
DEFSTAN 00-970(PT0)/9(2012) : 2012 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/17(2016) : 2016 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/14(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 02-862(PT1)/3(2011) : 2011 NAVAL FASTENERS - PART 1: MATERIAL SELECTION AND USE
DEFSTAN 00-970(PT0)/15(2015) : 2015 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/12(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 05-133(PT1)/1(2011) : 2011 METHODS FOR TESTING PAINTS, CHEMICALS AND ASSOCIATED PRODUCTS - PART 1: PAINTS AND ALLIED PRODUCTS
DEFSTAN 00-970(PT0)/11(2013) : 2013 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/13(2014) : 2014 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 03-4/6(2011) : 2011 THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA
DEFSTAN 00-970(PT0)/8(2011) : 2011 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 80-16/5(2011) : 2011 PAINT REMOVER, DICHLOROMETHANE, WATER RINSABLE - TYPE 1: HIGH VISCOSITY (BRUSHING) - TYPE 2: LOW VISCOSITY (SPRAYING)
DEFSTAN 00-970(PT0)/10(2013) : 2013 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
DEFSTAN 00-970(PT0)/16(2015) : 2015 DESIGN AND AIRWORTHINESS REQUIREMENTS FOR SERVICE AIRCRAFT - PART 0: PROCEDURES FOR USE, CONTENT AND DEFINITIONS
11/30252412 DC : 0 BS 4A 116 - STEEL PAN HEAD BOLTS (UNIFIED THREADS) (CADMIUM PLATED) FOR AIRCRAFT
BS SP134-SP138(1968) : 1968 AEROSPACE SERIES - SPECIFICATION FOR COPPER BERYLLIUM CRINKLE WASHERS
BS SP107-112(1954) : 1954 SPECIFICATIONS FOR TAB WASHERS FOR UNIFIED HEXAGONS FOR AIRCRAFT
SBAC TS 120 : 6 AGS2000 SERIES STIFFNUTS (INCLUDING CLINCH NUTS) BA & BSF THREADS FOR AIRCRAFT
BS 4A 116:2012 Steel pan head bolts (Unified threads), cadmium plated, for aircraft
BS 2SP91-92(1973) : 1973 SPECIFICATION FOR CARBON STEEL WORM DRIVE CLAMPS FOR AIRCRAFT
BS 4A 228:1997 Specification for steel double hexagon bolts. 1250 MPa (180,000 lbf/in<sup>2</sup>) for aircraft
BS SP 41-46(1951) : 1951 SPECIFICATIONS FOR TAB WASHERS FOR B.A. AND B.S.W. HEXAGONS FOR AIRCRAFT
BS 3SP 1:2013 Specification. Shackles, carbon steel, cadmium plated for aircraft
BS SP22-27(1950) : 1950 SPECIFICATION FOR BA WASHERS - FOR AIRCRAFT PURPOSES (PRIMARILY FOR FOR INSTRUMENT USE
13/30274750 DC : 0 BS 2A 204 ETC+A3 - SPECIFICATIONS FOR MACHINE SCREWS AND NUTS (UNIFIED THREADS) BELOW 1/4 INCH FOR AERONAUTICAL PURPOSES
BS 2SP81&2SP82(1973) : 1973 SPECIFICATION FOR SNAP HEAD HIGH NICKEL-COPPER ALLOY RIVETS
SAE AMS03-4A : 2015(S2017) THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF SPECIFIED MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA
BS 2SP87&2SP88(1973) : 1973 AEROSPACE SERIES - 100 DEGREES COUNTERSUNK HEAD HIGH NICKEL-COPPER ALLOY RIVETS
BS 4A102(2002) : 2002 AEROSPACE SERIES - SPECIFICATION FOR STEEL BOLTS (UNIFIED HEXAGONS AND UNIFIED THREADS) FOR AIRCRAFT
BS ISO 9940:2015 Aerospace series. Fluid, hydraulic, phosphate ester-base, fire resistant. Technical specification
SAE AMS 79-017 : 2017 COMPOUND, CLEANING, FOAMING, FOR AIRCRAFT SURFACES
BS 4A113(1999) : 1999 AEROSPACE SERIES - SPECIFICATION FOR CADMIUM-PLATED, MUSHROOM-HEADED, UNIFIED-THREAD, SLOTTED DRIVE BOLTS
14/30302298 DC : 0 BS ISO 9940 - AEROSPACE SERIES - FLUID, HYDRAULIC, PHOSPHATE ESTER-BASE, FIRE RESISTANT - TECHNICAL SPECIFICATION
11/30254199 DC : 0 BS 3 SP 1 - SPECIFICATION - CARBON STEEL SHACKLES, CADMIUM PLATED
12/30234431 DC : 0 BS ISO 9940 - AEROSPACE - FIRE RESISTANT HYDRAULIC FLUIDS
13/30290460 DC : 0 BS ISO 9940 - AEROSPACE SERIES - FLUID, HYDRAULIC, PHOSPHATE ESTER-BASE, FIRE RESISTANT - TECHNICAL SPECIFICATION
BS 3A125 TO 3A[...](1981) : 1981 AEROSPACE SERIES - SPECIFICATION FOR STIFFNUTS (UNIFIED THREADS) FOR AIRCRAFT

BS EN ISO 4516:2002 Metallic and other inorganic coatings. Vickers and Knoop microhardness tests
BS 2868:1968 Specification for cadmium anodes and cadmium oxide for electroplating
BS EN ISO 3543:2001 Metallic and non-metallic coatings. Measurement of thickness. Beta backscatter method
DEFSTAN 03-36/2(2010) : 2010 GUIDANCE TO THE USE OF CADMIUM ALTERNATIVES IN THE PROTECTIVE COATING OF DEFENCE EQUIPMENT
DEFSTAN 03-14/4(2008) : 2008 ELECTRODEPOSITION OF CHROMIUM FOR ENGINEERING PURPOSES
BS EN ISO 6507-1:2005 Metallic materials. Vickers hardness test Test method
BS EN ISO 2178:2016 Non-magnetic coatings on magnetic substrates. Measurement of coating thickness. Magnetic method
DEFSTAN 03-21/4(2008) : 2008 MECHANICAL METHODS FOR THE INDUCEMENT OF RESIDUAL SURFACE COMPRESSIVE STRESSES
BS EN ISO 3497:2001 Metallic coatings. Measurement of coating thickness. X-ray spectrometric methods
DEFSTAN 03-4/5(2006) : 2006 THE PRE-TREATMENT AND PROTECTION OF STEEL ITEMS OF MAXIMUM TENSILE STRENGTH EXCEEDING 1450 MPA
BS EN ISO 2177:2004 Metallic coatings. Measurement of coating thickness. Coulometric method by anodic dissolution
BS EN ISO 1463:2004 Metallic and oxide coatings. Measurement of coating thickness. Microscopical method
DEFSTAN 03-2/5(2009) : 2009 CLEANING AND PREPARATION OF METAL SURFACES
BS 6338:1982 Specification for chromate conversion coatings on electroplated zinc and cadmium coatings

View more information
US$57.50
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.