DEFSTAN 22-92/1(2006) : 2006
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
SPECIFICATION FOR THE MANUFACTURE OF 153 MM BORE REELABLE ASTERN HOSE AND COUPLINGS FOR REPLENISHMENT AT SEA FOR USE WITH DIESO
Hardcopy , PDF
03-26-2007
English
01-01-2006
Foreword
1 Scope
2 Warning
3 Normative References
4 Definitions
4.1 Receiving Ship
4.2 Original Defence Standard
4.3 Mandatory Clauses in Defence Standards
5 Abbreviations and Definitions
6 Performance Specification
6.1 Manufacturer's Tests
7 Standards/Requirements
7.1 Manufacture
7.1.1 Quality
7.1.2 Quality Approval
7.1.3 Method
7.1.4 Construction of 225 metre Reelable Refuelling
Hose
7.1.5 Hose Marking
7.1.6 Dimensions and Tolerances
7.1.6.1 Length of Assembly
7.1.6.2 Bore
7.1.6.3 Outside Diameter
7.1.6.4 Concentricity
7.1.6.5 Weight
7.2 Installation On-Board Ships
7.2.1 Installation on Receiving Ships
7.2.2 Hose Service Life
7.2.3 Acceptance of Hoses
7.2.4 Stowage On-Board
7.2.5 Maintenance
7.2.6 Periodic Testing
7.3 Storage and Issue
7.3.1 Hose Stowage Life
7.4 Identification and Packing
7.5 Oils and Greases
7.5.1 Responsibility for Inspection
8 Design Requirements/Guidance
8.1 Materials
8.1.1 Lining
8.1.2 Reinforcement
8.1.3 Bonding Wire
8.1.4 Cover
8.2 Couplings and Split Clamps
8.3 Production Test and Inspection
8.3.1 Visual Inspection
8.3.2 Batch Test
8.3.3 Acceptance Standard
Annex A - Testing and Test Report Requirements
A.1 Manufacturer's Testing
A.2 Rubber Properties Material Tests
A.3 Adhesion Test
A.4 Crush Test
A.5 Bend Radius Test
A.6 Bend Test
A.7 Low-Temperature Flexibility Test
A.8 Hydrostatic Tests
A.9 Proof Pressure and Axial Rotation Test
A.10 Electrical Continuity Tests
A.11 Burst Test
A.12 Elongation and Neckdown Tests
A.13 Tensile Pull
A.14 Test on the Hose Inclusive of the Area of the Splice
A.15 Coupling Tests
A.15.1 Tensile Pull
A.15.2 High Pressure Hold Test
A.15.3 Proof Test
A.15.4 Coupling to Coupling Test for Split Clamp
Assemblies
A.16 Manufacturer's Test Report Requirements
Annex B - Visible Defects in Synthetic Rubber Hose
B.1 Introduction
Annex C - Hose Identification Panel
Annex D - Bend Test
D.1 Sample
D.2 Method
D.3 Requirement
Annex E - Low-Temperature Flexibility Test
E.1 Method
Annex F - Method of Measuring the Free Length of a Hose
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.