• There are no items in your cart

DIN EN ISO 11296-3:2011-07

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 3: LINING WITH CLOSE-FIT PIPES
Available format(s)

Hardcopy , PDF

Superseded date

05-01-2019

Language(s)

German, English

Published date

01-01-2011

National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings
7 Ancillary components
8 Fitness for purpose of the installed lining system
  at the 'I' stage
9 Installation practice
Annex A (normative) - Factory folded heat reverted
        polyethylene (PE) pipe - Determination of
        memory ability
Annex B (normative) - Folded polyethylene (PE) pipe -
        Determination of resistance to circumferential
        tensile stress at constant temperature
Bibliography

This standard is included in DIN Handbook 13-4.

DevelopmentNote
Supersedes DIN EN 13566-3. (07/2011) DRAFT 2017 issued in September 2017. (09/2017)
DocumentType
Standard
Pages
28
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 11296-3:2018 Identical
EN ISO 11296-3:2011 Identical
ISO 11296-3:2009 Identical

DIN HDBK 13-4 : 10ED 2015 ABWASSERTECHNIK 4 - ABWASSERKANAELE, ABWASSERLEITUNGEN - PLANUNG, VERLEGUNG, BETRIEB, SANIERUNG

DIN EN ISO 9967:2016-07 THERMOPLASTICS PIPES - DETERMINATION OF CREEP RATIO (ISO 9967:2016)
ISO 13953:2001 Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
DIN EN ISO 6259-1:2015-08 THERMOPLASTICS PIPES - DETERMINATION OF TENSILE PROPERTIES - PART 1: GENERAL TEST METHOD (ISO 6259-1:2015)
ISO 8772:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polyethylene (PE)
ISO 2507-1:1995 Thermoplastics pipes and fittings — Vicat softening temperature — Part 1: General test method
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
DIN EN ISO 11295:2016-08 (Draft) CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION
ISO 12176-1:2017 Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
DIN EN ISO 11296-1:2011-07 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL
ISO 18373-1:2007 Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature
DIN EN ISO 9969:2016-06 THERMOPLASTICS PIPES - DETERMINATION OF RING STIFFNESS (ISO 9969:2016)
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
ISO 9967:2016 Thermoplastics pipes Determination of creep ratio
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 21138-1:2007 Plastics piping systems for non-pressure underground drainage and sewerage Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) Part 1: Material specifications and performance criteria for pipes, fittings and system
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
ISO 9852:2007 Unplasticized poly(vinyl chloride) (PVC-U) pipes — Dichloromethane resistance at specified temperature (DCMT) — Test method

View more information
US$101.53
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.