• There are no items in your cart

DIN EN ISO 11296-4:2011-07

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES
Available format(s)

Hardcopy , PDF

Superseded date

09-21-2018

Language(s)

German, English

Published date

01-01-2011

National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the 'M' stage
6 Fittings at the 'M' stage
7 Ancillary components
8 Fitness for purpose of the installed lining
  system at the 'I' stage
9 Installation practice
Annex A (informative) - CIPP components and
        their functions
Annex B (normative) - Cured-in-place pipes - Modifications
        to ISO 178 for flexural testing
Annex C (normative) - Cured-in-place pipes - Test method
        or the determination of long-term
        flexural modulus under wet conditions
Annex D (normative) - Cured-in-place pipes - Determination
        of the creep factor under dry conditions from
        a three-point flexural test
Bibliography

This standard is included in DIN Handbook 13-4.

DevelopmentNote
Supersedes DIN EN 13566-4. (07/2011) DRAFT 2017 issued in May 2017. (05/2017)
DocumentType
Standard
Pages
42
PublisherName
German Institute for Standardisation (Deutsches Institut für Normung)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 11296-4:2009 Identical
EN ISO 11296-4:2018 Identical

DIN HDBK 13-4 : 10ED 2015 ABWASSERTECHNIK 4 - ABWASSERKANAELE, ABWASSERLEITUNGEN - PLANUNG, VERLEGUNG, BETRIEB, SANIERUNG

ISO 25780:2011 Plastics piping systems for pressure and non-pressure water supply, irrigation, drainage or sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Pipes with flexible joints intended to be installed using jacking techniques
ISO 8773:2006 Plastics piping systems for non-pressure underground drainage and sewerage Polypropylene (PP)
ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
DIN EN ISO 11295:2016-08 (Draft) CLASSIFICATION AND INFORMATION ON DESIGN OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION
DIN EN ISO 1043-1:2016-09 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMERS AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011 + AMD.1:2016)
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
DIN EN ISO 899-2:2015-06 PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING (ISO 899-2:2003 + AMD.1:2015)
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 13002:1998 Carbon fibre Designation system for filament yarns
DIN EN ISO 11296-1:2011-07 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 1: GENERAL
ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
ISO 7684:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the creep factor under dry conditions
ISO 4435:2003 Plastics piping systems for non-pressure underground drainage and sewerage Unplasticized poly(vinyl chloride) (PVC-U)
EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
ISO 178:2010 Plastics Determination of flexural properties
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
DIN EN ISO 13002:1999-01
DIN EN ISO 75-2:2013-08 PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013)

View more information
US$120.59
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.