DIN EN ISO 20753:2014-07
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
PLASTICS - TEST SPECIMENS (ISO 20753:2008)
Hardcopy , PDF
02-05-2019
German
01-01-2014
National foreword
National Annex NA (informative) - Bibliography
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Types of test specimen and their dimensions
6 Report on preparation of test specimens
Annex A (informative) - Recommended applications
for multipurpose test specimens or parts
thereof
Annex B (normative) - Designation system for
test specimens
Bibliography
This standard is included in DIN Handbook KUNSTSTOFFE BAND 1.
DevelopmentNote |
DRAFT 2017 issued in June 2017. (06/2017)
|
DocumentType |
Standard
|
Pages |
23
|
PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
Status |
Superseded
|
SupersededBy |
Standards | Relationship |
ISO 20753:2008 | Identical |
EN ISO 20753:2014 | Identical |
DIN EN ISO 17855-2:2016-06 | PLASTICS - POLYETHYLENE (PE) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 17855-2:2016) |
DIN EN ISO 16012:2016-02 | PLASTICS - DETERMINATION OF LINEAR DIMENSIONS OF TEST SPECIMENS (ISO 16012:2015) |
DIN EN ISO 306:2014-03 | Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) |
DIN EN ISO 19069-2:2016-07 | PLASTICS - POLYPROPYLENE (PP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 19069-2:2016) |
DIN EN ISO 16396-2:2017-07 | Plastics - Polyamide (PA) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 16396-2:2017) |
DIN EN ISO 306 E : 2014 | PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) (ISO 306:2013) |
DIN EN ISO 16012 E : 2016 | PLASTICS - DETERMINATION OF LINEAR DIMENSIONS OF TEST SPECIMENS (ISO 16012:2015) |
DIN EN ISO 20028-2:2015-08 (Draft) | PLASTICS - THERMOPLASTIC POLYESTER (TP) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES (ISO 20028-2:2017) |
DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
DIN HDBK KUNSTSTOFFE BAND 1 : 2016 | HANDBUCH KUNSTSTOFFE - BAND 1 - MECHANISCHE UND THERMISCHE EIGENSCHAFTEN - PRUEFNORMEN |
IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
ISO 4589-3:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test |
ISO 10350-2:2011 | Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics |
DIN EN ISO 294-5:2015-08 (Draft) | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 5: PREPARATION OF STANDARD SPECIMENS FOR INVESTIGATING ANISOTROPY (ISO 294-5:2017) |
ISO 22088-1:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 1: General guidance |
DIN EN ISO 179-2:2012-06 | PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 2: INSTRUMENTED IMPACT TEST (ISO 179-2:1997 + AMD.1:2011) |
DIN EN ISO 22088-6:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 6: Slow strain rate method (ISO 22088-6:2006) |
ISO 293:2004 | Plastics — Compression moulding of test specimens of thermoplastic materials |
ISO 3167:2014 | Plastics Multipurpose test specimens |
VDE 0303-6 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
ISO 294-5:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy |
ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
DIN EN 60426 : 2007 COR 1 2010 | ELECTRICAL INSULATING MATERIALS - DETERMINATION OF ELECTROLYTIC CORROSION CAUSED BY INSULATING MATERIALS - TEST METHODS |
ISO 294-3:2002 | Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates |
ISO 22088-2:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 2: Constant tensile load method |
DIN EN ISO 10350-1:2016-08 (Draft) | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017) |
ISO 295:2004 | Plastics — Compression moulding of test specimens of thermosetting materials |
ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
ISO 22088-5:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 5: Constant tensile deformation method |
ISO 2039-1:2001 | Plastics Determination of hardness Part 1: Ball indentation method |
ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
ISO 11359-2:1999 | Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature |
VDE 0303-11 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
DIN EN 60112 : 2010 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
DIN EN ISO 1183-1:2013-04 | PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD (ISO 1183-1:2012) |
ISO 75-2:2013 | Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite |
DIN EN ISO 294-2:2006-05 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - SMALL TENSILE BARS |
ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
DIN EN ISO 4589-2:2016-03 (Draft) | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST (ISO 4589-2:2017) |
DIN EN ISO 899-2:2015-06 | PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 2: FLEXURAL CREEP BY THREE-POINT LOADING (ISO 899-2:2003 + AMD.1:2015) |
ISO 2039-2:1987 | Plastics Determination of hardness Part 2: Rockwell hardness |
ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
DIN EN ISO 4589-3:2016-03 (Draft) | PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 3: ELEVATED-TEMPERATURE TEST (ISO 4589-3:2017) |
DIN EN ISO 180:2013-08 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000 + AMD.1:2006 + AMD.2:2013) |
ISO 180:2000 | Plastics Determination of Izod impact strength |
ISO 22088-3:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method |
DIN EN ISO 295:2004-05 | Plastics - Compression moulding of test specimens of thermosetting materials (ISO 295:2004) |
DIN EN ISO 294-3:2003-12 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 3: SMALL PLATES |
ISO 294-2:1996 | Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars |
ISO 899-2:2003 | Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading |
ISO 1183-1:2012 | Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method |
ISO 1183-2:2004 | Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method |
ISO 1183-3:1999 | Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method |
ISO 604:2002 | Plastics — Determination of compressive properties |
DIN EN ISO 11403-1:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 1: Mechanical properties (ISO 11403-1:2014) |
ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
DIN EN ISO 2039-2:2000-01 | PLASTICS - DETERMINATION OF HARDNESS - PART 2: ROCKWELL HARDNESS |
IEC 60426:2007 | Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods |
DIN EN ISO 294-1:2017-09 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017) |
ISO 306:2013 | Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST) |
ISO 22088-4:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 4: Ball or pin impression method |
DIN EN ISO 293:2005-10 | Plastics - Compression moulding of test specimens of thermoplastic materials (ISO 293:2004) |
ISO 294-1:2017 | Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens |
ISO 22088-6:2006 | Plastics Determination of resistance to environmental stress cracking (ESC) Part 6: Slow strain rate method |
ISO 4589-2:2017 | Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test |
ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
ISO 899-1:2017 | Plastics — Determination of creep behaviour — Part 1: Tensile creep |
ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
DIN EN ISO 11403-3:2014-09 | Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014) |
ASTM D 1822 : 2013 : REDLINE | Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials |
DIN EN ISO 10724-1:2002-04 | PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOSETTING POWDER MOULDING COMPOUNDS (PMCS) - PART 1: GENERAL PRINCIPLES AND MOULDING OF MULTIPURPOSE TEST SPECIMENS |
ISO 178:2010 | Plastics Determination of flexural properties |
DIN EN ISO 22088-5:2009-10 | Plastics - Determination of resistance to environmental stress cracking (ESC) - Part 5: Constant tensile deformation method (ISO 22088-5:2006) |
DIN EN ISO 75-2:2013-08 | PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE (ISO 75-2:2013) |
DIN EN ISO 10350-2:2011-06 | PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS |
DIN EN ISO 604:2003-12 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
DIN EN ISO 3167:2014-11 | PLASTICS - MULTIPURPOSE TEST SPECIMENS (ISO 3167:2014) |
ISO 868:2003 | Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.