DOD-STD-35-36 Revision B:1979

Withdrawn

AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM SEALS, GASKETS AND PACKING

Available format(s)

PDF

Withdrawn date

07-20-2005

Publisher

US Military Specs/Standards/Handbooks

1. SCOPE
   1.1 General
   1.2 Purpose
   1.3 Utilization
   1.4 Military Specification Exception Title Index
2. REFERENCED DOCUMENTS
   2.1 Issues of Documents
   2.2 Other publications
3. Definition
4. GENERAL REQUIREMENTS
   4.1 Introduction
   4.2 Specification Requirement Sheet (SRS)
   4.3 Configuration
       4.3.1 Dimensions
       4.3.2 Illustrations
   4.4 Units of measure
5 DETAILED REQUIREMENTS
  5.1 Introduction
  5.2 MSE Formats
  5.3 Referenced documents
  5.4 Test matrix
  5.5 Tabulation
  5.6 Keyword Code Index (KCI) and Standard Paragraph
      5.6.1 Interrelationship of Codes
      5.6.2 Automatic MSE Data
      5.6.3 DOD STD 35 Tables
APPENDICES
Appendix A. Illustrations
         B. Characteristics Code Index
Index
Tables

Describes detailed requirements for the preparation of Military Specification Exception (MSE) documentation for Seals, Gaskets, and Packing.

Committee	AREA - EGDS
DevelopmentNote	B NOTICE 1 - Notice of Change B NOTICE 4 - Notice of Group Cancellation without replacement (08/2005)
DocumentType	Standard
Pages	301
PublisherName	US Military Specs/Standards/Handbooks
Status	Withdrawn

ASTM D 297 : 2015 : REDLINE	Standard Test Methods for Rubber Products—Chemical Analysis
FED-STD-601 Base Document:1955	RUBBER, SAMPLING AND TESTING
DOD STD 35 : D	AUTOMATED ENGINEERING DOCUMENT PREPARATION SYSTEM
ASTM E 228 : 2017 : REDLINE	Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
ASTM E 380 : 1993	Standard Practice for Use of the Internation System of Units (SI) (the Modernized Metric System) (Withdrawn 1997)
MIL-P-5315 Revision B:1964	PACKING, PREFORMED, HYDROCARBON FUEL RESISTANT
MIL-STD-130 Revision N:2007	IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
MIL-STD-810 Revision G:2008	ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS
ASTM D 1149 : 2016-02	TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT
ASTM E 384 : 2017 : REDLINE	Standard Test Method for Microindentation Hardness of Materials
MIL-STD-177 Revision A:1969	Rubber Products, Terms for Visible Defects of
ASTM D 792 : 2013 : REDLINE	Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ASTM D 413 : 1998	Standard Test Methods for Rubber Property-Adhesion to Flexible Substrate
ASME B46.1 : 2009	SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
FED-STD-66 Revision D:1979	STEEL, CHEMICAL COMPOSITION AND HARDENABILITY
ASTM E 10 : 2017-05	TEST METHOD FOR BRINELL HARDNESS OF METALLIC MATERIALS
MIL-STD-417 Revision A:1976	CLASSIFICATION SYSTEM AND TESTS FOR SOLID ELASTOMERIC MATERIALS
ASTM E 110 : 2014 : REDLINE	Standard Test Method for Rockwell and Brinell Hardness of Metallic Materials by Portable Hardness Testers
FED-STD-191 Revision A:1978	TEXTILE TEST METHODS
MIL F 17111 : B	FLUID, POWER TRANSMISSION
MIL-STD-1523 Revision A:1984	AGE CONTROLS OF AGE-SENSITIVE ELASTOMERIC MATERIAL
MIL-HDBK-692 Revision B:1983	A Guide to the Selection of Rubber O-Rings
ASTM D 1081 : 1960 : R1974	Test for Evaluating Rubber Property Sealing Pressure (Withdrawn 1983)
MIL-W-12332 Revision A:1964	WELDING, RESISTANCE, SPOT, SEAM, AND PROJECTION, FOR FABRICATING ASSEMBLIES OF LOW-CARBON STEEL
MIL H 5606 : G	HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE
MIL P 81716 : 0	PACKING, PREFORMED, STRAIGHT THREAD TUBE FITTING BOSS, TYPE II HYDRAULIC (MINUS 65 DEG F TO PLUS 275 DEG F)
FED-STD-H28 Revision A:1994	Screw-Thread Standards for Federal Services
MIL-HDBK-212 Base Document:1958	GASKET MATERIALS (NONMETALLIC)
ASTM D 471 : 2016-02	TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS
FED-STD-595 Revision C:2008	COLORS USED IN GOVERNMENT PROCUREMENT
MIL-HDBK-695 Revision F:2017	RUBBER PRODUCTS: RECOMMENDED SHELF LIFE
ASTM E 92 : 2017 : REDLINE	Standard Test Methods for Vickers Hardness and Knoop Hardness of Metallic Materials