• There are no items in your cart

EN 12622:2009+A1:2013

Current
Current

The latest, up-to-date edition.

Safety of machine tools - Hydraulic press brakes
Published date

10-23-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviations
4 List of significant hazards
5 Safety requirements and/or measures
6 Verification of the safety requirements and/or
  protective measures
7 Information for use
Annex A (normative) - Calculation of minimum
        safety distances
Annex B (normative) - The overall response time
        of the press brake stopping performance
Annex C (informative) - Example of redundant and
        monitored hydraulic control circuits for a
        down-stroking press brake
Annex D (normative) - Conditions for noise
        measurement of press brakes
Annex E (informative) - Side safeguarding for
        manually fed press brakes
Annex F (informative) - Markings
Annex G (normative) - Laser actuated AOPD system
        tests
Annex H (informative) - Bending speed
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42
Bibliography

This European Standard specifies technical safety requirements and protective measures to be adopted by persons undertaking the design, manufacture and supply of hydraulic press brakes which are designed to work cold metal or material partly of metal and hereafter referred to as machines.This European Standard also covers hydraulic press brakes, whose primary intended use is the cold working of metal, which are to be used in the same way to work other sheet materials such as cardboard or plastic.The requirements in this European Standard take account of intended use, including foreseeable misuse as defined in 3.22 of EN ISO 12100-1:2003. This European Standard presumes access to the press brake from all directions, deals with the hazards described in Clause 4, and specifies the safety measures for both the operator and other exposed persons.This European Standard also applies to:- ancillary devices which are an integral part of the press brake, e.g. back gauges and adjustable front sheet supports; - machines which are integrated into an automatic production line where the hazards and risk arising are comparable to those of machine working separately.The requirements of this European Standard apply to all hydraulic press brakes whatever the technology used in their control system, e.g. electromechanical and/ or electronic.This European Standard does not apply to machines whose principal designed purpose is:a)sheet folding by rotary action;b)tube and pipe bending by rotary action;c)roll bending.This European Standard applies to machines built after the date of issue of this European Standard.This European Standard does not cover the safety aspect of automatic loading and unloading equipment.Some guidance how to take into account additional automatic loading and unloading equipment can be found in ISO 11161.

Committee
CEN/TC 143
DevelopmentNote
2009 Edition Re-Issued in October 2013 & incorporates AMD 1 2013. (10/2013)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

I.S. EN 13128:2001 SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES)
I.S. EN 14070:2003 SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES
CSA Z142 : 2010 : FR CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS
BS EN 13128 : 2001 SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES)
DIN EN 14070:2009-07 SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES
EN 12717:2001+A1:2009 Safety of machine tools - Drilling machines
CSA Z142 :2010 CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS
CSA Z142 : 2010 : R2014 CODE FOR POWER PRESS OPERATION: HEALTH, SAFETY, AND SAFEGUARDING REQUIREMENTS
DIN EN 13128:2009-09 SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES)
I.S. EN 12717:2001 SAFETY OF MACHINE TOOLS - DRILLING MACHINES
16/30343615 DC : 0 BS ISO 14955-4 - MACHINE TOOLS - ENVIRONMENTAL EVALUATION OF MACHINE TOOLS - PART 4: PRINCIPLES FOR MEASURING METAL-FORMING MACHINE TOOLS AND LASER PROCESSING MACHINE TOOLS WITH RESPECT TO ENERGY EFFICIENCY
DIN EN 12717:2009-07 SAFETY OF MACHINE TOOLS - DRILLING MACHINES
UNI EN 12717 : 2009 SAFETY OF MACHINE TOOLS - DRILLING MACHINES
UNI EN 14070 : 2009 SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES
UNI EN 13128 : 2009 SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES)
BS EN 12717 : 2001 SAFETY OF MACHINE TOOLS - DRILLING MACHINES
BS EN 14070 : 2003 SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES
EN 13128:2001+A2:2009/AC:2010 SAFETY OF MACHINE TOOLS - MILLING MACHINES (INCLUDING BORING MACHINES)
EN 14070:2003+A1:2009/AC:2010 SAFETY OF MACHINE TOOLS - TRANSFER AND SPECIAL-PURPOSE MACHINES

EN 1005-4:2005+A1:2008 Safety of machinery - Human physical performance - Part 4: Evaluation of working postures and movements in relation to machinery
ISO 11202:2010 Acoustics Noise emitted by machinery and equipment Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections
ISO 7010:2011 Graphical symbols Safety colours and safety signs Registered safety signs
EN 894-3:2000+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators
EN 12464-1:2011 Light and lighting - Lighting of work places - Part 1: Indoor work places
EN 982:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Hydraulics
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
EN 1037:1995+A1:2008 Safety of machinery - Prevention of unexpected start-up
ISO 14122-3:2016 Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
ISO 3744:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Engineering methods for an essentially free field over a reflecting plane
ISO 14122-1:2016 Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access
ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements
EN 60825-1:2014/AC:2017-06 SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements
EN 1088:1995+A2:2008 Safety of machinery - Interlocking devices associated with guards - Principles for design and selection
CLC/TS 61496-2:2006 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
IEC 61310-2:2007 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
ISO/TR 11688-1:1995 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 1: Planning
EN 894-2:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 2: Displays
EN 61310-2:2008 Safety of machinery - Indication, marking and actuation - Part 2: Requirements for marking
ISO 13732-1:2006 Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
EN 50370-2:2003 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 2: Immunity
EN ISO 14121-1:2007 Safety of machinery - Risk assessment - Part 1: Principles (ISO 14121-1:2007)
EN 1837:1999+A1:2009 Safety of machinery - Integral lighting of machines
EN 999:1998+A1:2008 Safety of machinery - The positioning of protective equipment in respect of approach speeds of parts of the human body
EN 349:1993+A1:2008 Safety of machinery - Minimum gaps to avoid crushing of parts of the human body
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
ISO 14738:2002 Safety of machinery — Anthropometric requirements for the design of workstations at machinery
EN ISO 13850:2015 Safety of machinery - Emergency stop function - Principles for design (ISO 13850:2015)
EN 1005-1:2001+A1:2008 Safety of machinery - Human physical performance - Part 1: Terms and definitions
IEC 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
EN 1005-2:2003+A1:2008 Safety of machinery - Human physical performance - Part 2: Manual handling of machinery and component parts of machinery
IEC 60947-5-1 : 4.0 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
IEC 60825-1:2014 Safety of laser products - Part 1: Equipment classification and requirements
IEC 61508-4:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations (see Functional Safety and IEC 61508)
EN 614-1:2006+A1:2009 Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles
EN ISO 13857:2008 Safety of machinery - Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 11688-2 : 2000 ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 14122-4:2016 Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
ISO 14121-1:2007 Safety of machinery Risk assessment Part 1: Principles
EN 574:1996+A1:2008 Safety of machinery - Two-hand control devices - Functional aspects - Principles for design
EN ISO 13732-1:2008 Ergonomics of the thermal environment - Methods for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)
EN 60947-3:2009/A2:2015 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015)
EN ISO 11161:2007/A1:2010 SAFETY OF MACHINERY - INTEGRATED MANUFACTURING SYSTEMS - BASIC REQUIREMENTS
ISO 3746:2010 Acoustics Determination of sound power levels and sound energy levels of noise sources using sound pressure Survey method using an enveloping measurement surface over a reflecting plane
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
CLC/TS 61496-3:2008 Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
EN ISO 14122-3:2016 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2016)
EN ISO 3746:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN 61496-1:2013/AC:2015 SAFETY OF MACHINERY - ELECTRO-SENSITIVE PROTECTIVE EQUIPMENT - PART 1: GENERAL REQUIREMENTS AND TESTS (IEC 61496-1:2012)
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN ISO 3744:2010 Acoustics - Determination of sound power levels and sound energy levels of noise sources using sound pressure - Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
EN 842:1996+A1:2008 Safety of machinery - Visual danger signals - General requirements, design and testing
EN ISO 14122-4:2016 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed ladders (ISO 14122-4:2016)
EN 62061:2005/A2:2015 SAFETY OF MACHINERY - FUNCTIONAL SAFETY OF SAFETY-RELATED ELECTRICAL, ELECTRONIC AND PROGRAMMABLE ELECTRONIC CONTROL SYSTEMS (IEC 62061:2005/A2:2015)
EN ISO 14122-2:2016 Safety of machinery - Permanent means of access to machinery - Part 2: Working platforms and walkways (ISO 14122-2:2016)
ISO 13849-2:2012 Safety of machinery — Safety-related parts of control systems — Part 2: Validation
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008 Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
EN ISO 12100-2:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
IEC 61496-1:2012 Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
EN ISO 13849-2:2012 Safety of machinery - Safety-related parts of control systems - Part 2: Validation (ISO 13849-2:2012)
EN 983:1996+A1:2008 Safety of machinery - Safety requirements for fluid power systems and their components - Pneumatics
EN 954-1 : 1996 SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN ISO 13849-1:2015 Safety of machinery - Safety-related parts of control systems - Part 1: General principles for design (ISO 13849-1:2015)
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
EN ISO 4871:2009 Acoustics - Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units
EN 1005-3:2002+A1:2008 Safety of machinery - Human physical performance - Part 3: Recommended force limits for machinery operation
IEC 61508-1:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 1: General requirements (see Functional Safety and IEC 61508)
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
IEC 62061:2005+AMD1:2012+AMD2:2015 CSV Safety of machinery - Functional safety of safety-related electrical, electronic and programmable electronic control systems
ISO 14122-2:2016 Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways
EN 50370-1 : 2005 Electromagnetic compatibility (EMC) - Product family standard for machine tools - Part 1: Emission
EN 60947-5-3:2013 Low-voltage switchgear and controlgear - Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDDB)
EN ISO 11688-1:2009 Acoustics - Recommended practice for the design of low-noise machinery and equipment - Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 14122-1:2016 Safety of machinery - Permanent means of access to machinery - Part 1: Choice of fixed means and general requirements of access (ISO 14122-1:2016)
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design
ISO/TR 11688-2:1998 Acoustics Recommended practice for the design of low-noise machinery and equipment Part 2: Introduction to the physics of low-noise design
EN ISO 11202:2010 Acoustics - Noise emitted by machinery and equipment - Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
EN ISO 14738:2008 Safety of machinery - Anthropometric requirements for the design of workstations at machinery (ISO 14738:2002, including Cor 1:2003 and Cor 2:2005)
IEC 61496-2:2013 Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN 61508-4:2010 Functional safety of electrical/electronic/programmable electronic safety-related systems - Part 4: Definitions and abbreviations
EN 894-1:1997+A1:2008 Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.