• There are no items in your cart

EN 14636-1:2009

Current
Current

The latest, up-to-date edition.

Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
Published date

11-04-2009

Foreword
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 General requirements
5 Pipes
6 Fittings
7 Joint performance
8 Dangerous substances
9 Manufacturer's installation recommendations
10 Evaluation of conformity
Annex A (normative) - Determination of a pipe's crushing
                      strength and ring bending tensile
                      strength using a pipe test piece
Annex B (normative) - Determination of a pipe's crushing
                      strength or the ring bending tensile
                      strength using test pieces sawn from
                      a pipe
Annex C (normative) - Assessment of longitudinal bending
                      moment resistance (BMR)
Annex D (normative) - Determination of the compressive
                      strength of polyester resin concrete
                      (PRC) using test pieces which are cut
                      from a pipe
Annex E (normative) - Determination of the fatigue strength
                      of a pipe under cyclic loading
Annex F (normative) - Assessment of the leak-tightness of a
                      pipe and its joints under short term
                      exposure to internal water pressure
Annex G (normative) - Determination of the long-term crushing
                      strength of a pipe, including the effects
                      of media attack, using the 50 years
                      reference point
Bibliography

This European Standard applies to pipes and fittings made from polyester resin concrete (PRC, see 3.1.23), intended to be used within a drain or sewer system operating without pressure. It applies to products for use in buried installations to be installed by open-trench techniques or pipe jacking.It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross-sections, from WN/HN 300/450 to WN/HN 1400/2100 for egg-shaped cross-sections and from DN 800 to DN 1800 for kite-shaped cross-sections.The intended use of these products is for the conveyance of sewage, rainwater and surface water at temperatures up to 50 °C, without pressure or occasionally at a head of pressure up to 0,5 bar ), and installed in areas subjected to vehicle and/or pedestrian traffic.NOTE 1The attention of readers is drawn to applicable requirements contained in EN 476.It specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking.The pipes are classified on the basis of the intended method of installation and cross-sectional shape.NOTE 2It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

Committee
CEN/TC 155
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement (ISO 11295:2017)
I.S. EN ISO 11295:2017 CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017)
BS EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Manholes and inspection chambers
I.S. EN 14636-2:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
NF EN 14636-2 : 2010 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
DIN EN 14636-2:2010-04 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
UNI EN 14636-2 : 2010 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
BS EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement

EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
EN 13121-1:2003 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
EN 637:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS REINFORCED PLASTICS COMPONENTS - DETERMINATION OF THE AMOUNTS OF CONSTITUENTS USING THE GRAVIMETRIC METHOD
EN 476:2011 General requirements for components used in drains and sewers
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 9001:2015 Quality management systems — Requirements
EN 1119:2009 Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
EN 705:1994/AC:1995 PLASTICS PIPING SYSTEMS - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPES AND FITTINGS - METHODS FOR REGRESSION ANALYSES AND THEIR USE

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.