• There are no items in your cart

EN 16506:2014

Current
Current

The latest, up-to-date edition.

Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
Published date

10-15-2014

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Pipes at the 'M' stage
6 Marking
7 Fittings at the 'M' stage
8 Lining system at the 'I' stage
9 Installation
10 Documentation
Annex A (normative) - Test method for anchoring strength of
        plastics inner layer by pull-off
Annex B (normative) - 'I' stage crushing strength test
Bibliography

This European Standard specifies performance requirements and describes test methods for pipes and fittings for the renovation of underground drain and sewer systems by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout. It is applicable to plastics inner layers and grout systems with or without steel reinforcement.This European Standard does not apply to the structural design of the lining system.NOTESystems with multiple annuli are available, but these are controlled by patent rights and not covered by this European Standard.

Committee
CEN/TC 165
DevelopmentNote
Supersedes PREN 16506. (10/2014)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

Standards Relationship
NS EN 16506 : 2014 Identical
NF EN 16506 : 2014 Identical
NBN EN 16506 : 2014 Identical
NEN EN 16506 : 2014 Identical
DIN EN 16506 E : 2014 Identical
UNE-EN 16506:2015 Identical
DIN EN 16506:2014-12 Identical
PN EN 16506 : 2014 Identical
I.S. EN 16506:2014 Identical
BS EN 16506:2014 Identical
UNI EN 16506 : 2014 Identical
SN EN 16506 : 2014 Identical

I.S. EN ISO 11295:2017 CLASSIFICATION AND INFORMATION ON DESIGN AND APPLICATIONS OF PLASTICS PIPING SYSTEMS USED FOR RENOVATION AND REPLACEMENT (ISO 11295:2017)
EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement (ISO 11295:2017)
BS EN ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement
ISO 11295:2017 Classification and information on design and applications of plastics piping systems used for renovation and replacement

EN 10048:1996 Hot rolled narrow steel strip - Tolerances on dimensions and shape
EN 15885:2010 Classification and characteristics of techniques for renovation and repair of drains and sewers
EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
EN 1107-2 : 2001 Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN 1542:1999 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
EN 14654-1:2014 Management and control of operational activities in drain and sewer systems outside buildings - Part 1: Cleaning
EN ISO 1133-2:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO 1133-2:2011)
EN ISO 11296-7:2013 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 7: Lining with spirally-wound pipes (ISO 11296-7:2011)
EN 10025-1:2004 Hot rolled products of structural steels - Part 1: General technical delivery conditions
EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
CEN/TR 14920:2005 Jetting resistance of drain and sewer pipes - Moving jet test method
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
EN 445:2007 Grout for prestressing tendons - Test methods
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
EN 13412:2006 Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
ISO 4624:2016 Paints and varnishes — Pull-off test for adhesion
ISO 11296-7:2011 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
EN 1979:1999 Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 11296-4:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 4: Lining with cured-in-place pipes
EN 13100-4:2012 Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing
EN 12814-2:2000 TESTING OF WELDED JOINTS OF THERMOPLASTICS SEMI-FINISHED PRODUCTS - PART 2: TENSILE TEST
EN ISO 4624:2016 Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016)
EN 10025-2:2004/AC:2005 HOT ROLLED PRODUCTS OF STRUCTURAL STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR NON-ALLOY STRUCTURAL STEELS
EN 1015-3:1999/A2:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 3: DETERMINATION OF CONSISTENCE OF FRESH MORTAR (BY FLOW TABLE)
EN 1015-6:1998/A1:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 6: DETERMINATION OF BULK DENSITY OF FRESH MORTAR
EN 1610:2015 Construction and testing of drains and sewers
EN 1916:2002/AC:2008 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
EN 13067:2012 Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies
ISO 1133-2:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 2: Method for materials sensitive to time-temperature history and/or moisture
ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
EN 14117:2004 Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products
EN 206:2013+A1:2016 Concrete - Specification, performance, production and conformity
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)
EN 12814-8:2001/AC:2003 TESTING OF WELDED JOINTS OF THERMOPLASTICS SEMI-FINISHED PRODUCTS - PART 8: REQUIREMENTS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.