EN 1756-1:2001+A1:2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Tail lifts - Platform lifts for mounting on wheeled vehicles - Safety requirements - Part 1: Tail lifts for goods
08-30-2021
03-05-2008
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of hazards
5 Safety requirements and/or protective measures
5.1 General requirements
5.2 Working area
5.3 Manual effort
5.4 Operating speeds
5.4.1 General
5.4.2 Vertical speed
5.4.3 Closing and opening speeds
5.4.4 Tilting speed
5.5 Load stability
5.5.1 Tilt angle
5.5.2 Stop devices
5.6 Limitations of travel
5.7 Layout of wires and pipes
5.8 Unauthorised operation
5.9 Isolation of energy sources
5.10 Tail lift stowage
5.10.1 Indication
5.10.2 Security
5.11 Crushing and shearing
5.12 Structure working coefficients
5.13 Platform
5.13.1 Surface
5.13.2 Bluntness of edges
5.13.3 Tail lift used as a link bridge
5.13.4 Visibility of platform
5.14 Drive systems
5.14.1 Unintentional movements
5.14.2 Mechanical suspension systems
5.14.3 Hydraulic systems
5.15 Safety devices
5.15.1 Safety mechanisms
5.15.2 Springs inside safety devices
5.16 Loading control
5.16.1 Prevention of lifting excessive loads
5.16.2 Excessive moment
5.17 Control devices
5.17.1 Hold-to run principle
5.17.2 Logic
5.17.3 Unintentional operation
5.17.4 One control device for several
movements
5.17.5 Several control devices for one
movement
5.18 Control positions
5.18.1 Multiple control positions
5.18.2 Location of control positions
6 Optional equipment
7 Verification of the safety requirements and/or
measures
8 Information for use
8.1 General
8.2 Tail lift used as a link bridge
8.3 Inherent risks associated with improper use
8.4 Location and nature of information for use
8.4.1 Marking on the tail lift
8.4.2 Handbooks
8.4.3 Inspection record
Annex A (informative) Tail lift mechanisms and types
A.1 Mechanisms
A.1.1 Parallelogram
A.1.2 Column
A.1.3 Telescopic
A.2 Types
A.2.1 Conventional: (full and part width)
A.2.2 Folding platform
A.2.3 Retractable
A.2.4 Rotary
A.2.5 Door mounted
A.2.6 Inset
A.2.7 Internally mounted
Annex B (normative) Crushing and shearing
B.1 General
B.2 Platform lifting and lowering
B.2.1 Two-hand control
B.2.2 Two-foot control
B.2.3 Toe guard
B.2.4 Hinged foot protector
B.2.5 Safety cut-out
B.2.6 Automatic toe protector
B.3 Platforms capable of lifting above vehicle
floor level
B.4 Platform closure
B.4.1 Two-hand control
B.4.2 Safety cut-out
Annex C (informative) Structure and drive system
Annex D (normative) Drive systems - Steel wire ropes
and chains
D.1 Recommended specifications of steel wire
ropes
D.2 Dimensions of pulley grooves
D.3 Flare angle
D.4 Fleet angles
D.5 Pitch circle
Annex E (normative) Examples of controls logic
Annex F (informative) Marking
Annex G (informative) Unintentional operation
Annex H (normative) Verification by the installer
H.1 Compatibility between the lift and the
vehicle
H.2 Static test
H.2.1 Deformation
H.2.2 Drift
H.3 Dynamic test
H.4 Test of operation and safety function
H.5 Test to verify that the tail lift
cannot lift excessive load
Annex I (informative) Overloads onto a platform
at vehicle floor level
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 98/37/EC
Annex ZB (informative) Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.