EN 20898-2 : 1993
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992)
Superseded date
03-01-2012
Published date
01-12-2013
Publisher
Foreword
1 Scope
2 Normative references
3 Designation system
4 Materials
5 Mechanical properties
6 Proof load values
7 Failure loads for nuts with nominal height
>= 0.5 D but < 0.8 D
8 Test methods
9 Marking
Annex A (informative) - Loadability of bolted
connections
Annex B (informative) - Bibliography
Annex ZA (normative) - Normative references to
international publications with their
relevant European publications
Describes the mechanical properties of nuts with specified proof load values when tested at room temperature.
| Committee |
TC 185
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| Standards | Relationship |
| NBN EN 20898-2 : 1994 | Identical |
| DIN ISO 898-2:1981-03 | Identical |
| SN EN 20898-2 : 1995 | Identical |
| NS ISO 898-2 : 1ED 1994 | Identical |
| ISO 898-2:2012 | Identical |
| UNI EN 20898-2 : 1994 | Identical |
| BS EN 20898-2:1994 | Identical |
| UNE-EN 20898-2:1994 | Identical |
| NF EN 20898-2 : 1994 | Identical |
| PN EN 20898-2 : 1998 | Identical |
| I.S. EN 20898-2:1994 | Identical |
| NBN EN 286-1 : 1998 AMD 2 2006 | Identical |
| NEN ISO 898-2 : 1994 | Identical |
| DIN EN 20898-2:1994-02 | Identical |
| 02/704463 DC : DRAFT MAR 2002 | PREN 14399-4 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 4: SYSTEM HV - HEXAGON BOLT AND NUT ASSEMBLIES |
| BS EN 50119 : 2009 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| I.S. EN 74-1:2005 | COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 1: COUPLERS FOR TUBES - REQUIREMENTS AND TEST PROCEDURES |
| DIN 6915:1999-12 | HEXAGON NUTS WITH LARGE WIDTHS ACROSS FLATS FOR HIGH STRENGTH STRUCTURAL BOLTING |
| DIN EN 15865:2009-08 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| DIN EN 15865 E : 2009 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| UNI EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| 03/318786 DC : DRAFT NOV 2003 | EN 14831 - FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| 10/30234610 DC : DRAFT NOV 2010 | BS EN 14420-3 - HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| 02/107768 DC : DRAFT DEC 2002 | BS EN 74-1 - COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 1: COUPLERS FOR TUBES - REQUIREMENTS AND TEST PROCEDURES |
| 08/30184289 DC : DRAFT SEP 2008 | BS EN 12561-6 - RAILWAY APPLICATIONS - TANK WAGONS - PART 6: MANHOLES |
| I.S. EN 1515-4:2009 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| UNE-EN 1993-1-8:2013 | Eurocode 3: Design of steel structures - Part 1-8: Design of joints |
| EN 14399-8:2007 | High-strength structural bolting assemblies for preloading - Part 8: System HV - Hexagon fit bolt and nut assemblies |
| 16/30336501 DC : 0 | BS EN 16951-2 - RAILWAY APPLICATIONS - TRACK - NOISE BARRIERS AND RELATED DEVICES ACTING ON AIRBORNE SOUND PROPAGATION - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 2: NON-ACOUSTIC CHARACTERISTICS |
| ONORM EN 1090-3 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| DIN EN 1090-3:2008-09 | EXECUTION OF STEEL AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL RULES FOR EXECUTION OF ALUMINIUM STRUCTURES |
| UNI EN 14399-7 : 2008 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| I.S. EN 15865:2009 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| I.S. EN 13480-2:2017 | METALLIC INDUSTRIAL PIPING - PART 2: MATERIALS |
| I.S. EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| BS EN 13480-2:2017 | Metallic industrial piping Materials |
| DIN EN 13261:2011-01 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - AXLES - PRODUCT REQUIREMENTS |
| DIN EN ISO 10484:2014-06 (Draft) | WIDENING TEST ON NUTS |
| BS EN ISO 7085:1999 | Mechanical and performance requirements of case hardened and tempered metric thread rolling screws |
| BS EN 13531 : 2001 | EARTH-MOVING MACHINERY - TIP-OVER PROTECTION STRUCTURE (TOPS) FOR COMPACT EXCAVATORS - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| BS EN 493:1992 | Fasteners. Surface discontinuities. Nuts |
| BS EN 877 : 1999 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| BS EN ISO 10484:2004 | Widening test on nuts |
| BS EN 13261 : 2009 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - AXLES - PRODUCT REQUIREMENTS |
| ISO 10964:1993 | Adhesives — Determination of torque strength of anaerobic adhesives on threaded fasteners |
| I.S. EN 877:2000 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| DIN EN 13411-5:2009-02 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS |
| EN 12952-14:2004 | Water-tube boilers and auxiliary installations - Part 14: Requirements for flue gas DENOX-systems using liquified pressurized ammonia and ammonia water solution |
| DIN EN 12952-14:2004-09 | Water-tube boilers and auxiliary installations - Part 14: Requirements for fluegas DENOX systems using liquified pressurized ammonia and ammonia water solution |
| EN 13411-5:2003+A1:2008 | Terminations for steel wire ropes - Safety - Part 5: U-bolt wire rope grips |
| UNI EN 877 : 2007 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 12561-6:2011 (edition 2) | Railway applications - Tank wagons - Part 6: Manholes |
| I.S. EN 12284:2003 | REFRIGERATING SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| DIN EN 1090-2:2011-10 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| EN 877:1999/A1:2006/AC:2008 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 13531:2001+A1:2008 | Earth-moving machinery - Tip-over protection structure (TOPS) for compact excavators - Laboratory tests and performance requirements (ISO 12117:1997 modified) |
| DIN EN 14399-8:2008-03 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| DIN EN ISO 16330:2004-08 | Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003) |
| 13/30277104 DC : 0 | BS EN 14389-1 - ROAD TRAFFIC NOISE REDUCING DEVICES - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 1: ACOUSTICAL CHARACTERISTICS |
| I.S. EN ISO 10964:1998 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| DIN EN 15001-1:2011-02 | Gas infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| 10/30234330 DC : DRAFT DEC 2010 | BS EN 12561-6 - RAILWAY APPLICATIONS - TANK WAGONS - PART 6: MANHOLES |
| 11/30215604 DC : 0 | BS IEC 60913 - RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 07/30166055 DC : 0 | BS EN 14399-10 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| UNI EN 1515-4 : 2010 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| PREN 14389-2 : DRAFT 2013 | ROAD TRAFFIC NOISE REDUCING DEVICES - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 2: NON-ACOUSTICAL CHARACTERISTICS |
| BS EN 15865:2009 | Adhesives. Determination of torque strength of anaerobic adhesives on threaded fasteners |
| UNE-EN 1090-2:2011 | Execution of steel structures and aluminium structures - Part 2: Technical requirements for steel structures |
| NF EN 1515-4 : 2010 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| UNI EN 14399-10 : 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| ONORM EN 14399-10 : JUN 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| UNI EN 1090-2 : 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| I.S. EN 50119:2009 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| DIN EN 877:2010-01 | Cast iron pipes and fittings, their joints and accessories for the evacuation of water from buildings - Requirements, test methods and quality assurance (includes Amendment A1:2006 and Corrigendum AC:2008) |
| DIN EN 13411-5 E : 2009 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS |
| DIN EN 12284:2004-01 | Refrigerating systems and heat pumps - Valves - Requirements, testing and marking |
| DIN EN 1993-1-8:2010-12 | Eurocode 3: Design of steel structures - Part 1-8: Design of joints (includes Corrigendum AC:2009) |
| ISO 14847:1999 | Rotary positive displacement pumps Technical requirements |
| I.S. EN ISO 7085:2000 | MECHANICAL AND PERFORMANCE REQUIREMENTS OF CASE HARDENED AND TEMPERED METRIC THREAD ROLLING SCREWS |
| DIN EN 74-1:2005-12 | Couplers, spigot pins and baseplates for use in falsework and scaffolds - Part 1: Couplers for tubes - Requirements and test procedures |
| I.S. EN ISO 10485:2004 | CONE PROOF LOAD TEST ON NUTS |
| I.S. EN 13531:2001 | EARTH-MOVING MACHINERY - TIP-OVER PROTECTION STRUCTURE (TOPS) FOR COMPACT EXCAVATORS - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| I.S. EN 13411-5:2003 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS |
| I.S. EN 12561-6:2011 | RAILWAY APPLICATIONS - TANK WAGONS - PART 6: MANHOLES |
| DIN EN ISO 10484:2004-10 | Widening test on nuts (ISO 10484:1997) |
| BS 6912-6(2000) : 2000 | EARTH-MOVING MACHINERY - FALLING-OBJECT PROTECTIVE STRUCTURES - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| BS 6912-14(2000) : 2000 | EARTH-MOVING MACHINERY ROLL-OVER PROTECTIVE STRUCTURES LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| BS EN 14399-8:2007 | High-strength structural bolting assemblies for preloading System HV. Hexagon fit bolt and nut assemblies |
| DIN EN 14399-10:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| 02/704462 DC : DRAFT MAR 2002 | PREN 14399-3 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 3: SYSTEM HR - HEXAGON BOLT AND NUT ASSEMBLIES |
| PREN 14389-1 : DRAFT 2013 | ROAD TRAFFIC NOISE REDUCING DEVICES - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 1: ACOUSTICAL CHARACTERISTICS |
| I.S. EN 493:1993 | FASTENERS - SURFACE DISCONTINUITIES - NUTS |
| I.S. EN ISO 898-6:1996 | MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD |
| NF EN 50119 : 2010 AMD 1 2013 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| 05/30132920 DC : DRAFT APR 2005 | EN 1090-2 - EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR THE EXECUTION OF STEEL STRUCTURES |
| NF EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| 06/30155635 DC : 0 | EN 13261 - RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - AXLES - PRODUCT REQUIREMENTS |
| I.S. EN 1090-3:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 3: TECHNICAL REQUIREMENTS FOR ALUMINIUM STRUCTURES |
| EN 14399-7:2007 | High-strength structural bolting assemblies for preloading - Part 7: System HR - Countersunk head bolt and nut assemblies |
| EN 1090-2:2008+A1:2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| EN 1090-3:2008 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| BS EN 1090-2 : 2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| DIN EN 1090-2:2015-07 (Draft) | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| DIN EN 14831 E : 2005 | FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| UNE-EN 15001-1:2010 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| BS EN 13627:2000 | Earth-moving machinery. Falling-object protective structures. Laboratory tests and performance requirements |
| UNE-EN 12561-6:2012 | Railway applications - Tank wagons - Part 6: Manholes |
| UNI EN 13261 : 2011 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - AXLES - PRODUCT REQUIREMENTS |
| EN 13261:2009+A1:2010 | Railway applications - Wheelsets and bogies - Axles - Product requirements |
| EN ISO 7085 : 1999 | MECHANICAL AND PERFORMANCE REQUIREMENTS OF CASE HARDENED AND TEMPERED METRIC THREAD ROLLING SCREWS |
| EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| UNI EN 14831 : 2005 | FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| UNI EN 13411-5 : 2009 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS |
| UNI EN 1106 : 2010 | MANUALLY OPERATED TAPS FOR GAS BURNING APPLIANCES |
| UNI EN 13531 : 2009 | EARTH-MOVING MACHINERY - TIP-OVER PROTECTION STRUCTURE (TOPS) FOR COMPACT EXCAVATORS - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| UNI EN 15001-1 : 2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| UNI EN 1993-1-8 : 2005 | EUROCODE 3 - DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS |
| ONORM EN 74-1 : 2006 | COUPLERS, SPIGOT PINS AND BASEPLATES FOR USE IN FALSEWORK AND SCAFFOLDS - PART 1: COUPLERS FOR TUBES - REQUIREMENTS AND TEST PROCEDURES |
| UNI EN 1854 : 2010 | PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES |
| UNI EN 12561-6 : 2011 | RAILWAY APPLICATIONS - TANK WAGONS - PART 6: MANHOLES |
| 09/30188143 DC : DRAFT OCT 2009 | BS EN 13480-2:2002/A2 - METALLIC INDUSTRIAL PIPING - PART 2: MATERIALS |
| I.S. EN 13510:2000 | EARTH-MOVING MACHINERY - ROLL-OVER PROTECTIVE STRUCTURES - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| 02/704460 DC : DRAFT MAR 2002 | PREN 14399-1 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| DIN 19207:2004-02 | Measurement of fluid flow by means of pressure differential devices - Threaded pipe end and accessories |
| BS EN 1515-4:2009 | Flanges and their joints. Bolting Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| 13/30277107 DC : 0 | BS EN 14389-2 - ROAD TRAFFIC NOISE REDUCING DEVICES - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 2: NON-ACOUSTICAL CHARACTERISTICS |
| 10/30234634 DC : 0 | BS EN 14423 - CLAMP TYPE COUPLING ASSEMBLIES FOR USE WITH STEAM HOSES RATED FOR PRESSURES UP TO 18 BAR |
| BS 6912-25(2001) : 2001 | EARTH-MOVING MACHINERY - TIP-OVER PROTECTION STRUCTURE (TOPS) FOR COMPACT EXCAVATORS - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| 08/30173031 DC : DRAFT JAN 2008 | BS EN 1515-4 - FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| UNI EN 15865 : 2009 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| 04/30123693 DC : DRAFT OCT 2004 | EN 15048-1 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| DIN EN 1515-4 E : 2010 | FLANGES AND THEIR JOINTS - BOLTING - PART 4: SELECTION OF BOLTING FOR EQUIPMENT SUBJECT TO THE PRESSURE EQUIPMENT DIRECTIVE 97/23/EC |
| NF EN 1090-2 : 2009 + A1 2011 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| DIN EN 14399-7:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| I.S. EN 15001-1:2009 | GAS INFRASTRUCTURE - GAS INSTALLATION PIPEWORK WITH AN OPERATING PRESSURE GREATER THAN 0,5 BAR FOR INDUSTRIAL INSTALLATIONS AND GREATER THAN 5 BAR FOR INDUSTRIAL AND NON-INDUSTRIAL INSTALLATIONS - PART 1: DETAILED FUNCTIONAL REQUIREMENTS FOR DESIGN, MATERIALS, CONSTRUCTION, INSPECTION AND TESTING |
| NF EN 13261 : 2009 + A1 2011 | RAILWAY APPLICATIONS - WHEELSETS AND BOGIES - AXLES - PRODUCT REQUIREMENTS |
| IEC 60913:2013 | Railway applications - Fixed installations - Electric traction overhead contact lines |
| BS EN 13480-2:2017+A3:2018 | Metallic industrial piping Materials |
| DIN EN 12952-14 E : 2004 | WATER-TUBE BOILERS AND AUXILIARY INSTALLATIONS - PART 14: REQUIREMENTS FOR FLUE GAS DENOX-SYSTEMS USING LIQUEFIED PRESSURIZED AMMONIA AND AMMONIA WATER SOLUTION |
| DIN EN ISO 6157-2:2004-10 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995) |
| BS EN 1661:1998 | Hexagon nuts with flange |
| BS EN ISO 10485:2004 | Cone proof load test on nuts |
| BS EN 12284:2003 | Refrigerating systems and heat pumps. Valves. Requirements, testing and marking |
| BS EN 74-1:2005 | Couplers, spigot pins and baseplates for use in falsework and scaffolds Part 1: Couplers for tubes - Requirements and test procedures |
| BS EN ISO 3269:2001 | Fasteners. Acceptance inspection |
| BS EN 13411-5 : 2003 | TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 5: U-BOLT WIRE ROPE GRIPS |
| BS EN ISO 16330:2003 | Reciprocating positive displacement pumps and pump units. Technical requirements |
| ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
| BS EN ISO 14847:1999 | Rotary positive displacement pumps. Technical requirements |
| BS EN 13510:2000 | Earth-moving machinery. Roll-over protective structures. Laboratory tests and performance requirements |
| I.S. EN 50119:2020 | Railway applications - Fixed installations - Electric traction overhead contact lines |
| UNE-EN 1515-4:2010 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| BS EN 12952-14:2004 | Water-tube boilers and auxiliary installations Requirements for flue gas DENOX-systems using liquified pressurized ammonia and ammonia water solution |
| ISO 10485:1991 | Cone proof load test on nuts |
| EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials |
| ISO 16330:2003 | Reciprocating positive displacement pumps and pump units Technical requirements |
| BS EN 1993-1-8:2005 | Eurocode 3. Design of steel structures Design of joints |
| BS EN ISO 6157-2:2004 | Fasteners. Surface discontinuities Nuts |
| BS EN 1515-1:2000 | Flanges and their joints. Bolting Selection of bolting |
| BS EN 14831:2005 | Fasteners. Tightening performance. Torque/Angle simplified test method |
| BS EN ISO 10964:1997 | Adhesives. Determination of torque strength of anaerobic adhesives on threaded fasteners |
| EN 50119 : 2009 AMD 1 2013 | RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRIC TRACTION OVERHEAD CONTACT LINES |
| EN 1515-4:2009 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| EN ISO 10484:2004 | Widening test on nuts (ISO 10484:1997) |
| EN ISO 10964 : 1997 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ADHESIVES ON THREADED FASTENERS |
| EN 15001-1:2009 | Gas Infrastructure - Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations - Part 1: Detailed functional requirements for design, materials, construction, inspection and testing |
| EN ISO 16330 : 2003 | RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS |
| EN 1515-1:1999 | Flanges and their joints - Bolting - Part 1: Selection of bolting |
| ONORM EN 877 : 2008 | CAST IRON PIPES AND FITTINGS, THEIR JOINTS AND ACCESSORIES FOR THE EVACUATION OF WATER FROM BUILDINGS - REQUIREMENTS, TEST METHODS AND QUALITY ASSURANCE |
| EN 13627 : 2000 | EARTH-MOVING MACHINERY - FALLING-OBJECT PROTECTIVE STRUCTURES - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| EN 1661:1997 | Hexagon nuts with flange (ISO/DIS 4161:1996, modified) |
| EN 1993-1-8:2005/AC:2009 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-8: DESIGN OF JOINTS |
| EN 286-1:1998/A2:2005 | SIMPLE UNFIRED PRESSURE VESSELS DESIGNED TO CONTAIN AIR OR NITROGEN - PART 1: PRESSURE VESSELS FOR GENERAL PURPOSES |
| EN ISO 6157-2:2004 | Fasteners - Surface discontinuities - Part 2: Nuts (ISO 6157-2:1995) |
| EN 493 : 1992 | FASTENERS - SURFACE DISCONTINUITIES - NUTS |
| EN ISO 14847 : 1999 | ROTARY POSITIVE DISPLACEMENT PUMPS - TECHNICAL REQUIREMENTS |
| EN ISO 10485:2004 | Cone proof load test on nuts (ISO 10485:1991) |
| EN 74-1:2005 | Couplers, spigot pins and baseplates for use in falsework and scaffolds - Part 1: Couplers for tubes - Requirements and test procedures |
| EN 14831:2005 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| EN ISO 898-6 : 1995 | MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD |
| EN 15865:2009 | Adhesives - Determination of torque strength of anaerobic adhesives on threaded fasteners (ISO 10964:1993 modified) |
| DIN EN 14399-10 E : 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 10: SYSTEM HRC - BOLT AND NUT ASSEMBLIES WITH CALIBRATED PRELOAD |
| BS EN 14399-7:2007 | High-strength structural bolting assemblies for preloading System HR. Countersunk head bolt and nut assemblies |
| I.S. EN ISO 6157-2:2004 | FASTENERS - SURFACE DISCONTINUITIES - PART 2: NUTS |
| I.S. EN ISO 10484:2004 | WIDENING TEST ON NUTS |
| PREN 14420-3 : DRAFT 2010 | HOSE FITTINGS WITH CLAMP UNITS - PART 3: CLAMP UNITS, BOLTED OR PINNED |
| 12/30257022 DC : 0 | BS EN 13611 - SAFETY AND CONTROL DEVICES FOR BURNERS AND APPLIANCES BURNING GASEOUS OR LIQUID FUELS - GENERAL REQUIREMENTS |
| PREN 16951-2 : DRAFT 2016 | RAILWAY APPLICATIONS - TRACK - NOISE BARRIERS AND RELATED DEVICES ACTING ON AIRBORNE SOUND PROPAGATION - PROCEDURES FOR ASSESSING LONG TERM PERFORMANCE - PART 2: NON-ACOUSTIC CHARACTERISTICS |
| BS EN 15001-1:2009 | Gas infrastructure. Gas installation pipework with an operating pressure greater than 0,5 bar for industrial installations and greater than 5 bar for industrial and non-industrial installations Detailed functional requirements for design, materials, construction, inspection and testing |
| DIN EN 1515-4:2010-04 | Flanges and their joints - Bolting - Part 4: Selection of bolting for equipment subject to the Pressure Equipment Directive 97/23/EC |
| DIN 3016-2:2000-06 | FASTENING CLAMPS - PART 2: WITH FASTENING LUGS |
| DIN EN 14399-8:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| I.S. EN 1090-2:2008 | EXECUTION OF STEEL STRUCTURES AND ALUMINIUM STRUCTURES - PART 2: TECHNICAL REQUIREMENTS FOR STEEL STRUCTURES |
| NF EN 15865 : 2009 | ADHESIVES - DETERMINATION OF TORQUE STRENGTH OF ANAEROBIC ON THREADED FASTENERS |
| I.S. EN 14399-7:2007 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 7: SYSTEM HR - COUNTERSUNK HEAD BOLT AND NUT ASSEMBLIES |
| UNI EN 14399-8 : 2008 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| BS EN 1090-3:2008 | Execution of steel structures and aluminium structures Technical requirements for aluminium structures |
| BS EN 14399-10:2009 | High-strength structural bolting assemblies for preloading System HRC. Bolt and nut assemblies with calibrated preload |
| UNE-EN 1090-3:2011 | Execution of steel structures and aluminium structures - Part 3: Technical requirements for aluminium structures |
| I.S. EN 14399-8:2007 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 8: SYSTEM HV - HEXAGON FIT BOLT AND NUT ASSEMBLIES |
| DIN EN 13531:2009-08 | EARTH-MOVING MACHINERY - TIP-OVER PROTECTION STRUCTURE (TOPS) FOR COMPACT EXCAVATORS - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS |
| DIN EN 12561-6:2011-10 | Railway applications - Tank wagons - Part 6: Manholes |
| ISO 10484:1997 | Widening test on nuts |
| BS EN 12561-6:2011 | Railway applications. Tank wagons Manholes |
| BS EN 286-1 : 1998 | SIMPLE UNFIRED PRESSURE VESSELS DESIGNED TO CONTAIN AIR OR NITROGEN - PART 1: PRESSURE VESSELS FOR GENERAL PURPOSES |
| DIN EN 14831:2005-07 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| EN 12284 : 2003 | REFRIGERATING SYSTEMS AND HEAT PUMPS - VALVES - REQUIREMENTS, TESTING AND MARKING |
| DIN EN 493:1992-07 | FASTENERS - SURFACE DISCONTINUITIES - NUTS |
| DIN EN ISO 898-6:1996-02 | MECHANICAL PROPERTIES OF FASTENERS - PART 6: NUTS WITH SPECIFIED PROOF LOAD VALUES - FINE PITCH THREAD |
| UNE-EN 13480-2:2017 | Metallic industrial piping - Part 2: Materials (Endorsed by Asociación Española de Normalización in September of 2019.) |
| ISO 272:1982 | Fasteners — Hexagon products — Widths across flats |
| ISO 6507-1:2005 | Metallic materials Vickers hardness test Part 1: Test method |
| ISO 4035:2012 | Hexagon thin nuts chamfered (style 0) — Product grades A and B |
| EN 20286-2 : 1993 | ISO SYSTEM OF LIMITS AND FITS - TABLES OF STANDARD TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS |
| ISO 4016:2011 | Hexagon head bolts Product grade C |
| ISO 4034:2012 | Hexagon regular nuts (style 1) Product grade C |
| BS 4395-1:1969 | Specification for high strength friction grip bolts and associated nuts and washers for structural engineering General grade |
| ISO 4015:1979 | Hexagon head bolts — Product grade B — Reduced shank (shank diameter approximately equal to pitch diameter) |
| ISO 1:2016 | Geometrical product specifications (GPS) Standard reference temperature for the specification of geometrical and dimensional properties |
| ISO 724:1993 | ISO general-purpose metric screw threads — Basic dimensions |
| ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
| ISO 4017:2014 | Fasteners Hexagon head screws Product grades A and B |
| ISO 4032:2012 | Hexagon regular nuts (style 1) — Product grades A and B |
| ISO 3506:1979 | Corrosion-resistant stainless steel fasteners — Specifications |
| BS 4190:1967 | Specification for ISO metric black hexagon bolts, screws and nuts |
| ISO 262:1998 | ISO general purpose metric screw threads — Selected sizes for screws, bolts and nuts |
| ISO 68:1973 | ISO general purpose screw threads Basic profile |
| BS 4500-1.2(1990) : AMD 7631 | ISO LIMITS AND FITS - GENERAL, TOLERANCES AND DEVIATIONS - TABLES OF COMMONLY USED TOLERANCE GRADES AND LIMIT DEVIATIONS FOR HOLES AND SHAFTS |
| ISO 4036:2012 | Hexagon thin nuts unchamfered (style 0) Product grade B |
| ISO 6506:1981 | Metallic materials — Hardness test — Brinell test |
| ISO 6508:1986 | Metallic materials Hardness test Rockwell test (scales A - B - C - D - E - F - G - H - K) |
| ISO 4964:1984 | Steel Hardness conversions |
| BS 4395-2:1969 | Specification for high strength friction grip bolts and associated nuts and washers for structural engineering Higher grade bolts and nuts and general grade washers |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
| ISO 4033:2012 | Hexagon high nuts (style 2) — Product grades A and B |
| ISO 261:1998 | ISO general purpose metric screw threads General plan |
| ISO 6157-2:1995 | Fasteners Surface discontinuities Part 2: Nuts |
| ISO 965-1:2013 | ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data |
| ISO 4014:2011 | Hexagon head bolts Product grades A and B |
| ISO 4018:2011 | Hexagon head screws Product grade C |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.