• There are no items in your cart

EN 60352-4:1994/A1:2000

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SOLDERLESS CONNECTIONS - PART 4: SOLDERLESS NON-ACCESSIBLE INSULATION DISPLACEMENT CONNECTIONS - GENERAL REQUIREMENTS, TEST METHODS AND PRACTICAL GUIDANCE
Amendment of

EN 60352-4:1994

Superseded date

08-20-2020

Published date

01-12-2013

FOREWORD
INTRODUCTION
SECTION 1: GENERAL
1 Scope
2 Object
3 Normative references
4 Definitions
5 IEC type designation
SECTION 2: REQUIREMENTS
6 Workmanship
7 Tools
8 Insulation displacement termination (ID termination)
9 Wires
10 Non-accessible insulation displacement connections
   (ID connections)
SECTION 3: TESTS
11 Testing
12 Type tests
13 Test schedules
SECTION 4: PRACTICAL GUIDANCE
14 General
15 Tool information
16 Termination information
17 Wire information
18 Connection information
19 ID connections, open housing design
20 ID connections, closed housing design
21 General additional information about ID connections
   as part of a multi-pole connector
22 Final remarks
Annex ZA (normative) Normative references to international
         publications with their corresponding European
         publications

Applies to non-accessible ID connections for which the tests and measurements of Section 3 are suitable and which are made with: - appropriately designed ID terminations; - wires having solid round conductors of 0,25 mm to 3,6 mm nominal diameter; - wires having stranded conductors of 0,05 square meter to 10 square meter cross-section; for use in telecommunication equipment and in electronic devices employing similar techniques.

Committee
SR 48B
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

09/30208429 DC : 0 BS EN 50467 - RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
BS EN 61076-3-100:2000 Connectors for use in d.c., low-frequency analogue and digital high-speed data applications Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row
UNE-EN 50467:2012 Railway applications - Rolling stock - Electrical connectors, requirements and test methods
I.S. EN 50467:2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
I.S. EN 62852:2015 CONNECTORS FOR DC-APPLICATION IN PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
BS EN 50548 : 2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
I.S. EN 50548:2011 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
EN 61076-3-101:1997 Connectors with assessed quality, for use in d.c. low-frequency analogue and in digital high-speed data applications - Part 3: Rectangular connectors - Section 101: Detail specification for a range of shielded connectors with trapezoidal shaped shells and non-removable rectangular contacts on a 1,27 mm x 2,54 mm centre-line
EN 61076-4-110:2002 Connectors for electronic equipment - Part 4-110: Printed board connectors with assessed quality - Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function
I.S. EN 61076-4:1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION - PRINTED BOARD CONNECTORS
12/30235292 DC : 0 BS EN 50343 - RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
BS EN 61076-3-101 : 1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE
CEI EN 61076-4-110 : 2003 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
CEI EN 50467 : 2013 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
PREN 50467 : DRAFT 2009 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
I.S. EN 60603-2:1998 CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES
I.S. EN 60947-7-4:2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013 (EQV))
CEI EN 50343 : 2015 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
BS EN 60603-7 : 2009 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS
UNE-EN 62852:2015 Connectors for DC-application in photovoltaic systems - Safety requirements and tests
EN 60603-7:2009/A1:2011 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008/A1:2011)
BS EN 62790:2015 Junction boxes for photovoltaic modules. Safety requirements and tests
09/30214460 DC : 0 BS EN 50548 - JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
CEI EN 61076-4 : 1997 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: SECTIONAL SPECIFICATION PRINTED BOARD CONNECTORS
DD CLC/TS 50467:2008 Railway applications. Rolling stock. Electrical connectors, requirements and test methods
I.S. EN 50173-1:2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
BS EN 50343 : 2014 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
BS EN 61076-4-105:1998 Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of applications including the telecommunication and audio industry
01/637057 DC : DRAFT AUG 2001 DRAFT EN 50173 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS
EN IEC 61076-2-111:2018 Connectors for electrical and electronic equipment - Product requirements - Part 2-111: Circular connectors - Detail specification for power connectors with M12 screw-locking
BS EN 50173-1:2011 Information technology. Generic cabling systems General requirements
EN 50173-1:2011 Information technology - Generic cabling systems - Part 1: General requirements
NF EN 61076 3 101 : 1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C. LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTER-LINE
I.S. EN 61076-3-104:2017 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 3-104: DETAIL SPECIFICATION FOR 8-WAY, SHIELDED FREE AND FIXED CONNECTORS FOR DATA TRANSMISSIONS WITH FREQUENCIES UP TO 2000 MHZ
I.S. EN 61984:2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
S.R. CLC/TS 50467:2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
UNE-EN 50521:2010 Connectors for photovoltaic systems - Safety requirements and tests
EN 62790:2015 Junction boxes for photovoltaic modules - Safety requirements and tests
EN 61076-4:1996 Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Sectional specification - Printed board connectors
CEI EN 60947-7-4 : 2014 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS
BS EN 60603-2:1998 Connectors for frequencies below 3 MHz for use with printed boards Detail specification for two-part connectors with assessed quality, for printed boards, for basic grid of 2,54 mm (0,1 in) with common mounting features
CEI EN 61076-3-101 : 1998 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D/C/ LOW-FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 3: RECTANGULAR CONNECTORS - SECTION 101: DETAIL SPECIFICATION FOR A RANGE OF SHIELDED CONNECTORS WITH TRAPEZOIDAL SHAPED SHELLS AND NON-REMOVABLE RECTANGULAR CONTACTS ON A 1,27 MM X 2,54 MM CENTRE-LINE
UNE-EN 60947-7-4:2014 Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors
BS EN 61076-4-110:2002 Connectors with assessed quality, for use in d.c., low-frequency analogue and in digital high speed data applications. Printed board connectors Detail specification for latched cable connector system having a basic grid of 2,0 mm including full shielding and latching function
NF EN 61076 4 105 : 1999 CONNECTORS WITH ASSESSED QUALITY, FOR USE IN D.C., LOW FREQUENCY ANALOGUE AND IN DIGITAL HIGH-SPEED DATA APPLICATIONS - PART 4: PRINTED BOARD CONNECTORS - SECTION 105: DETAIL SPECIFICATION FOR 9 MM CIRCULAR CONNECTOR WITH 3 TO 8 CONTACTS FOR USE IN A WIDE RANGE OF APPLICATIONS INCLUDING THE TELECOMMUNICATION AND AUDIO INDUSTRY
CEI EN 50173-1 : 2011 INFORMATION TECHNOLOGY - GENERIC CABLING SYSTEMS - PART 1: GENERAL REQUIREMENTS
I.S. EN 60603-7:2009 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 7: DETAIL SPECIFICATION FOR 8-WAY, UNSHIELDED, FREE AND FIXED CONNECTORS (IEC 60603-7:2008)
I.S. EN 61076-4-110:2002 CONNECTORS FOR ELECTRONIC EQUIPMENT - PART 4-110: PRINTED BOARD CONNECTORS WITH ASSESSED QUALITY - DETAIL SPECIFICATION FOR LATCHED CABLE CONNECTOR SYSTEM HAVING A BASIC GRID OF 2,0 MM INCLUDING FULL SHIELDING AND LATCHING FUNCTION
BS EN 60947-7-4:2013 Low-voltage switchgear and controlgear Ancillary equipment. PCB terminal blocks for copper conductors
UNE-EN 62790:2015 Junction boxes for photovoltaic modules - Safety requirements and tests
I.S. EN 50343:2014 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
BS EN 61984:2009 Connectors. Safety requirements and tests
EN 62852:2015 Connectors for DC-application in photovoltaic systems - Safety requirements and tests
BS EN 50521 : 2009 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
08/30179116 DC : DRAFT MAR 2008 BS EN 50521 - CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
CLC/TS 50467 : 2008 COR 2008 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
BS EN 61076-4-107:2001 Connectors for electronic equipment Printed board connectors with assessed quality. Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations
BS EN 50467:2011 Railway applications. Rolling stock. Electrical connectors, requirements and test methods
BS EN 61076-3-104:2017 Connectors for electrical and electronic equipment. Product requirements Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz
I.S. EN 50521:2008 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
UNE-EN 50548:2012 Junction boxes for photovoltaic modules
I.S. EN IEC 61076-2-111:2018 CONNECTORS FOR ELECTRICAL AND ELECTRONIC EQUIPMENT - PRODUCT REQUIREMENTS - PART 2-111: CIRCULAR CONNECTORS - DETAIL SPECIFICATION FOR POWER CONNECTORS WITH M12 SCREW-LOCKING
PREN 50548 : DRAFT 2009 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
EN 61076-3-104:2017 Connectors for electrical and electronic equipment - Product requirements - Part 3-104: Detail specification for 8-way, shielded free and fixed connectors for data transmissions with frequencies up to 2 000 MHz
EN 50548 : 2011 AMD 2 2014 JUNCTION BOXES FOR PHOTOVOLTAIC MODULES
EN 60603-2:1998/A1:2005 CONNECTORS FOR FREQUENCIES BELOW 3 MHZ FOR USE WITH PRINTED BOARDS - PART 2: DETAIL SPECIFICATION FOR TWO-PART CONNECTORS WITH ASSESSED QUALITY, FOR PRINTED BOARDS, FOR BASIC GRID OF 2,54 MM (0,1 IN) WITH COMMON MOUNTING FEATURES
EN 50521:2008/A1:2012 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
EN 61984:2009 Connectors - Safety requirements and tests
EN 61076-4-107:2001 Connectors for electronic equipment - Part 4-107: Printed board connectors with assessed quality - Detail specification for shielded two-part connectors having a basic grid of 2,0 mm, fixed part with solder and press-in terminations for printed boards, free part with non-accessible insulation displacement and crimp terminations
EN 61076-3-100:2000 Connectors for use in d.c., low-frequency analogue and digital high speed data applications - Part 3-100: Rectangular connectors with assessed quality - Detail specification for a range of shielded connectors with trapezoidal-shaped shells and non-removable ribbon contacts on a 1,27 mm double row
EN 50467 : 2011 RAILWAY APPLICATIONS - ROLLING STOCK - ELECTRICAL CONNECTORS, REQUIREMENTS AND TEST METHODS
EN 50343 : 2014 AMD 1 2017 RAILWAY APPLICATIONS - ROLLING STOCK - RULES FOR INSTALLATION OF CABLING
EN 60947-7-4 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-4: ANCILLARY EQUIPMENT - PCB TERMINAL BLOCKS FOR COPPER CONDUCTORS (IEC 60947-7-4:2013)

IEC GUIDE 109:2012 Environmental aspects - Inclusion in electrotechnical product standards
IEC 60352-3:1993 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
IEC 60068-1:2013 Environmental testing - Part 1: General and guidance
IEC 60512-6:1984 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 6: Climatic tests and soldering tests
IEC 60068-2-60:2015 RLV Environmental testing - Part 2-60: Tests - Test Ke: Flowing mixed gas corrosion test
EN 60352-3:1994 Solderless connections - Part 3: Solderless accessible insulation displacement connections - General requirements, test methods and practical guidance
EN 60068-1:2014 Environmental testing - Part 1: General and guidance
ISO 1463:2003 Metallic and oxide coatings Measurement of coating thickness Microscopical method
EN 60512-1:2001 Connectors for electronic equipment - Tests and measurements - Part 1: General
EN 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11- 7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
IEC 60512-11-7:2003 Connectors for electronic equipment - Tests and measurements - Part 11-7: Climatic tests - Test 11g: Flowing mixed gas corrosion test
IEC 60512-4:1976 Electromechanical components for electronic equipment; basic testing procedures and measuring methods. Part 4: Dynamic stress tests
IEC 60512-5:1992 Electromechanical components for electronic equipment; basic testing procedures and measuring methods - Part 5: Impact tests (free components), static load tests (fixed components), endurance tests and overload tests
IEC 60512-1:2001 Connectors for electronic equipment - Tests and measurements - Part 1: General
IEC 60050-581:2008 International Electrotechnical Vocabulary (IEV) - Part 581: Electromechanical components for electronic equipment
IEC 60189-3:2007 Low-frequency cables and wires with PVC insulation and PVC sheath - Part 3: Equipment wires with solid or stranded conductor wires, PVC insulated, in singles, pairs and triples

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.