EN 61167:2016

Superseded

View Superseded by

Metal halide lamps - Performance specification

Superseded date

02-03-2022

Published date

06-10-2016

Publisher

European Committee for Standards - Electrical

European foreword
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Lamp requirements
5 Information for ballast, ignitor and luminaire
  design
6 Data sheets
Annex A (normative) - Method of measuring lamp
        starting and warm-up characteristics
Annex B (normative) - Method of measuring electrical
        and photometrical characteristics (lamps for
        operation on 50 Hz or 60 Hz supply
        frequencies)
Annex C (normative) - Method of test for lumen
        maintenance and life
Annex D (informative) - Information for luminaire
        design
Annex E (normative) - Method of measuring electrical
        and photometrical characteristics on low
        frequency square wave reference ballast
Annex F (normative) - Spectral analysis of power
        ripple: calculation procedure for amplitude
        spectrum ratio and guidance
Annex G (informative) - Low frequency square wave
        operation
Annex H (informative) - Information for ballast design
Annex I (informative) - Information regarding lamp
        performance temperature limits for
        luminaire design
Annex J (informative) - ILCOS codes
Bibliography
Annex ZA (normative) - Normative references to
         international publications with their
         corresponding European publications
Annex ZZA (informative) - Relationship between this
          European Standard and the ecodesign
          requirements of Commission Regulation
          (EC) No 245/2009 aimed to be covered
Annex ZZB (informative) - Relationship between this
          European Standard and the ecodesign
          requirements of Commission Regulation
          (EU) No 1194/2012 aimed to be covered
Annex ZZC (informative) - Relationship between this
          European Standard and the energy labelling
requirements of Commission Delegated Regulation
          (EU) No 874/2012 aimed to be covered
Standard and the ecodesign requirements

IEC 61167:2015 specifies the performance requirements for metal halide lamps for general lighting purposes. This third edition replaces the second edition published in 2011. This third edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition.a) A set of new lamp data sheets (20 W, 35 W, 50 W, 100 W) is introduced.b) Reference to ILCOS (International lamp coding system) is removed from the lamp data sheets and now located in a new annex.c) Information on outer bulb temperature (and in some cases also on pin temperature and temperature adjacent to cap) is replaced with an explanation on differences in manufacturers' construction; this explanation is given in detail in a new annex.

DocumentType	Standard
PublisherName	European Committee for Standards - Electrical
Status	Superseded
SupersededBy	EN 61167:2018
Supersedes	EN 61167:2011

Standards	Relationship
NF EN 61167 : 2016	Identical
NBN EN 61167 : 2016	Identical
NEN EN IEC 61167 : 2016	Identical
I.S. EN 61167:2016	Identical
I.S. EN 61167:1995	Identical
ONORM OVE EN 61167 : 2017	Identical
PN EN 61167 : 2016	Identical
SN EN 61167 : 2016	Identical
CEI EN 61167 : 2018	Identical
UNE-EN 61167:2016	Identical
BS EN 61167:2011	Identical
CEI EN 61167 : 2016	Identical
DIN EN 61167:2012-03	Identical

EN 60188:2001	High-pressure mercury vapour lamps - Performance specifications
IEC 60682:1980	Standard method of measuring the pinch temperature of quartz-tungsten-halogen lamps
IEC TR 61341:2010	Method of measurement of centre beam intensity and beam angle(s) of reflector lamps
IEC 60188:2001	High-pressure mercury vapour lamps - Performance specifications
IEC 60050-845:1987	International Electrotechnical Vocabulary (IEV) - Part 845: Lighting
EN 61231:2010/A1:2013	INTERNATIONAL LAMP CODING SYSTEM (ILCOS) (IEC 61231:2010/A1:2013)
IEC 62321-4:2013+AMD1:2017 CSV	Determination of certain substances in electrotechnical products - Part 4: Mercury in polymers, metals and electronics by CV-AAS, CV-AFS, ICP-OES and ICP-MS
EN 13032-4:2015	Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 4: LED lamps, modules and luminaires
EN 60923:2005/A1:2006	AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS
EN 60927:2007/A1:2013	AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - PERFORMANCE REQUIREMENTS (IEC 60927:2007/A1:2013 (34C/951/CDV))
IEC 60410:1973	Sampling plans and procedures for inspection by attributes
EN 60357:2003/A11:2016	TUNGSTEN HALOGEN LAMPS (NON-VEHICLE) - PERFORMANCE SPECIFICATIONS
EN 61341:2011	Method of measurement of centre beam intensity and beam angle(s) of reflector lamps
IEC 62035:2014+AMD1:2016 CSV	Discharge lamps (excluding fluorescent lamps) - Safety specifications
EN 62035:2014	Discharge lamps (excluding fluorescent lamps) - Safety specifications
IEC 61231:2010+AMD1:2013 CSV	International lamp coding system (ILCOS)
IEC 60598-1:2014+AMD1:2017 CSV	Luminaires - Part 1: General requirements and tests
IEC 60061-1:2005 CSV	Lamp caps and holders together with gauges for the control of interchangeability and safety - Part 1: Lamp caps
IEC 62471:2006	Photobiological safety of lamps and lamp systems
IEC 60927:2007+AMD1:2013 CSV	Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements
IEC 61126:1992	Procedure for use in the preparation of maximum lamp outlines
EN 13032-1:2004+A1:2012	Light and lighting - Measurement and presentation of photometric data of lamps and luminaires - Part 1: Measurement and file format
IEC 60923:2005+AMD1:2006 CSV	Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements
EN 62471:2008	Photobiological safety of lamps and lamp systems
EN 60682:1993/A2:1997	METHOD OF MEASURING THE PINCH TEMPERATURE OF QUARTZ GLASS LAMPS