EN 61347-1:2015
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Lamp controlgear - Part 1: General and safety requirements
Amended by
Superseded date
01-26-2021
Published date
05-15-2015
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 General notes on tests
6 Classification
7 Marking
8 Terminals
9 Earthing
10 Protection against accidental contact with live parts
11 Moisture resistance and insulation
12 Electric strength
13 Thermal endurance test for windings of ballasts
14 Fault conditions
15 Construction
16 Creepage distances and clearances
17 Screws, current-carrying parts and connections
18 Resistance to heat, fire and tracking
19 Resistance to corrosion
20 No-load output voltage
Annex A (normative) - Test to establish whether a
conductive part is a live part which may cause
an electric shock
Annex B (normative) - Particular requirements for
thermally protected lamp controlgear
Annex C (normative) - Particular requirements for
electronic lamp controlgear with means of
protection against overheating
Annex D (normative) - Requirements for carrying out
the heating tests of thermally protected lamp
controlgear
Annex E (normative) - Use of constant S other than
4500 in tw tests
Annex F (normative) - Draught-proof enclosure
Annex G (normative) - Explanation of the derivation of
the values of pulse voltages
Annex H (normative) - Tests
Annex I (normative) - Additional requirements for
built-in magnetic ballasts with double or
reinforced insulation
Annex J (normative) - Schedule of more onerous
requirements
Annex K (informative) - Conformity testing during
manufacture
Annex L (normative) - Particular additional requirements
for controlgears providing SELV
Annex M (informative) - Dielectric strength test voltages
for controlgear intended for the use in impulse
withstand Category III
Annex N (normative) - Requirements for insulation materials
used for double or reinforced insulation
Annex O (normative) - Additional requirements for built-in
electronic controlgear with double
or reinforced insulation
Annex P (normative) - Creepage distances and clearances
and distance through isolation (DTI) for lamp
controlgear which are protected against pollution
by the use of coating or potting
Annex Q (informative) - Example for Up calculation
Annex R (informative) - Concept of creepage distances
and clearances
Annex S (informative) - Examples of controlgear
insulation coordination
Annex T (informative) - Creepage distances and clearances
for controlgear with a higher degree of availability
(impulse withstand category III)
Bibliography
Annex ZA (normative) - Normative references to
international publications with their
corresponding European publications
NEW! IEC 61347-1:2015 is available as IEC Standards+ 61347-1:2015 which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61347-1:2015 specifies general and safety requirements for lamp controlgear for use on d.c. supplies up to 250 V and/or a.c. supplies up to 1 000 V at 50 Hz or 60 Hz. This third edition cancels and replaces the second edition published in 2007, Amendment 1:2010 and Amendment 2:2012. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) additional marking requirements;
b) additional requirements for creepage distances and clearances:
- for working voltages with operating frequencies up to 30 kHz;
- for working voltages with higher operating frequencies than 30 kHz;
- for impulse and resonance voltages ignition;
- for basic, supplementary and reinforced insulation;
- for insulation between circuits;
- for coated or potted controlgear;
c) modification of definition of ELV and FELV;
d) modification of schematic drawing, showing the different controlgear classification and insulation requirements;
e) scope extension;
f) new Annex A: test to establish whether a conductive part is a live part which may cause an electric shock;
g) new Annex M: creepage distances and clearances for controlgear where a higher degree of availability (impulse withstand category III) may be requested;
h) new Annex Q: example for Up calculation;
i) new Annex P: creepage distances and clearances and distance through isolation (DTI) for lamp controlgear which are protected against pollution by the use of coating or potting;
j) new Annex R: concept of creepage distances and clearances.
| Committee |
CLC/TC 34
|
| DevelopmentNote |
Together with the parts 2-1 to 2-9 of EN 61347 supersedes EN 60920, EN 60922, EN 60924, EN 60926, EN 60928 and EN 61046 (05/2001)
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| CEI EN 61347-1 : 2016 | Identical |
| I.S. EN 61347-1:2015 | Identical |
| VDE 0712-30 : 2016 COR 1 2017 | Identical |
| SS-EN 61347-1:2015 | Identical |
| NF EN 61347-1 : 2015 | Identical |
| NBN EN 61347-1 : 2015 | Identical |
| NEN EN IEC 61347-1 : 2015 | Identical |
| UNE-EN 61347-1:2016 | Identical |
| PN EN 61347-1 : 2015 | Identical |
| DIN EN 61347-1 : 2016 COR 1 2017 | Identical |
| SN EN 61347-1:2015 | Identical |
| SN EN 61347-1 : 2001 | Identical |
| IEC 61347-1:2015 RLV | Identical |
| BS EN 61347-1:2015 | Identical |
| CEI EN 62733 : 2017 | PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - GENERAL AND SAFETY REQUIREMENTS |
| UNE-EN 61347-2-9:2013 | Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
| BS EN 61047:2004 | D.C. or A.C. supplied electronic step-down convertors for filament lamps. Performance requirements |
| BS EN 62386-207:2009 | Digital addressable lighting interface Particular requirements for control gear. LED modules (device type 6) |
| BS EN 62386-205:2009 | Digital addressable lighting interface Particular requirements for control gear. Supply voltage controller for incandescent lamps (device type 4) |
| I.S. EN 62386-210:2011 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 210: PARTICULAR REQUIREMENTS FOR CONTROL GEAR - SEQUENCER (DEVICE TYPE 9) (IEC 62386-210:2011 (EQV)) |
| BS EN 61347-2-12 : 2005 | LAMP CONTROLGEAR - PART 2-12: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC BALLASTS FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) |
| BS EN 62504:2014 | General lighting. Light emitting diode (LED) products and related equipment. Terms and definitions |
| I.S. EN 61347-2-2:2012 | LAMP CONTROLGEAR - PART 2-2: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS (IEC 61347-2-2:2011 (EQV)) |
| CEI EN 61347-2-2 : 2012 | LAMP CONTROLGEAR - PART 2-2: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC STEPDOWN CONVERTORS FOR FILAMENT LAMPS |
| BS EN 60929 : 2011 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| BS EN 61347-2-9:2013 | Lamp controlgear Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
| I.S. EN 62560:2012&A1:2015&A11:2019 | SELF-BALLASTED LED-LAMPS FOR GENERAL LIGHTING SERVICES BY VOLTAGE > 50 V - SAFETY SPECIFICATIONS |
| I.S. EN 60923:2005 | AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS |
| UNE-EN 60968:2015 | Self-ballasted fluorescent lamps for general lighting services - Safety requirements |
| EN IEC 61347-2-14:2018 | Lamp controlgear - Part 2-14: Particular requirements for DC and/or AC supplied electronic controlgear for fluorescent induction lamps |
| I.S. EN 61347-2-6:2001 | LAMP CONTROLGEAR - PART 2-6: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR AIRCRAFT LIGHTING (IEC 61347-2-6:2000 (EQV)) |
| DIN EN 12665:2016-09 (Draft) | LIGHT AND LIGHTING - BASIC TERMS AND CRITERIA FOR SPECIFYING LIGHTING REQUIREMENTS |
| EN IEC 60079-7:2015/A1:2018 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015/A1:2017) |
| BS EN 62733:2015 | Programmable components in electronic lamp controlgear. General and safety requirements |
| EN 61347-2-5:2001/corrigendum:2010 | LAMP CONTROLGEAR - PART 2-5: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR PUBLIC TRANSPORT LIGHTING |
| EN 62838:2016/AC:2017-11 | LEDSI LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES NOT EXCEEDING 50 V A.C. R.M.S. OR 120 V RIPPLE FREE D.C. - SAFETY SPECIFICATIONS |
| EN 62733:2015/AC:2017-09 | PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - GENERAL AND SAFETY REQUIREMENTS |
| EN 62386-207 : 2009 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 207: PARTICULAR REQUIREMENTS FOR CONTROL GEAR - LED MODULES (DEVICE TYPE 6) |
| EN 60968:2015 | Self-ballasted fluorescent lamps for general lighting services - Safety requirements |
| EN 61347-2-13:2014/A1:2017 | LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES |
| EN 61347-2-6:2001/corrigendum:2010 | LAMP CONTROLGEAR - PART 2-6: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR AIRCRAFT LIGHTING |
| EN 62386-103:2014 | Digital addressable lighting interface - Part 103: General requirements - Control devices |
| EN 60927:2007/A1:2013 | AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - PERFORMANCE REQUIREMENTS (IEC 60927:2007/A1:2013 (34C/951/CDV)) |
| EN 62386-204 : 2009 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 204: PARTICULAR REQUIREMENTS FOR CONTROL GEAR - LOW VOLTAGE HALOGEN LAMPS (DEVICE TYPE 3) |
| EN 62386-209 : 2011 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 209: PARTICULAR REQUIREMENTS FOR CONTROL GEAR - COLOUR CONTROL (DEVICE TYPE 8) |
| EN 61347-2-12:2005/A1:2010 | LAMP CONTROLGEAR - PART 2-12: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC BALLASTS FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) |
| EN 62718:2016 | Railway applications - Rolling stock - DC supplied electronic ballasts for lighting fluorescent lamps |
| EN 61347-2-2:2012 | Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
| EN 62776:2015 | Double-capped LED lamps designed to retrofit linear fluorescent lamps - Safety specifications |
| EN 61347-2-7:2012 | Lamp controlgear - Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| EN 61347-2-9:2013 | Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
| EN 62386-205 : 2009 | Digital addressable lighting interface - Part 205: Particular requirements for control gear - Supply voltage controller for incandescent lamps (device type 4) |
| CEI EN 50107-2 : 2005 | SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 2: REQUIREMENTS FOR EARTH-LEAKAGE AND OPEN-CIRCUIT PROTECTIVE DEVICES |
| BS EN 62386-210:2011 | Digital addressable lighting interface Particular requirements for control gear. Sequencer (device type 9) |
| BS EN 62386-202:2009 | Digital addressable lighting interface Particular requirements for control gear. Self-contained emergency lighting (device type 1) |
| CEI EN 62532 : 2012 | FLUORESCENT INDUCTION LAMPS - SAFETY SPECIFICATIONS |
| BS EN 62718:2016 | Railway applications. Rolling stock. DC supplied electronic ballasts for lighting fluorescent lamps |
| 16/30342256 DC : 0 | BS EN 50107-3 - PRODUCT STANDARD COVERING LUMINOUS SIGNS WITH DISCHARGE LAMPS AND/OR LED (LIGHT EMITTING DIODES) AND/OR EL (ELECTROLUMINESCENT) LIGHTSOURCES WITH A NOMINAL VOLTAGE NOT EXCEEDING 1000 V, WITH THE EXCLUSION OF GENERAL LIGHTING, TRAFFIC- OR EMERGENCY RELATED PURPOSE |
| BS EN 62034:2012 | Automatic test systems for battery powered emergency escape lighting |
| I.S. EN 62386-101:2014 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 101: GENERAL REQUIREMENTS - SYSTEM COMPONENTS |
| BS EN 60923:2005 | Auxiliaries for lamps. Ballasts for discharge lamps (excluding tubular fluorescent lamps). Performance requirements |
| BS EN 60921:2004 | Ballasts for tubular fluorescent lamps. Performance requirements |
| I.S. EN 61347-2-4:2001 | LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING (IEC 61347-2-4:2000 (EQV)) |
| I.S. EN 60929:2011 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| BS EN 61347-2-11:2002 | Lamp controlgear Particular requirements for miscellaneous electronic circuits used with luminaires |
| CEI EN 62034 : 2013 | AUTOMATIC TEST SYSTEMS FOR BATTERY POWERED EMERGENCY ESCAPE LIGHTING |
| I.S. EN 62811:2015 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS FOR LOW FREQUENCY SQUAREWAVE OPERATION |
| BS EN 60079-7 : 2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' (IEC 60079-7:2015) |
| BS EN 61347-2-8 : 2001 | LAMP CONTROLGEAR - PART 2-8: PARTICULAR REQUIREMENTS FOR BALLASTS FOR FLUORESCENT LAMPS |
| I.S. EN 62931:2017 | GX16T-5 CAPPED TUBULAR LED LAMP - SAFETY SPECIFICATIONS |
| BS EN 60927 : 2007 | AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - PERFORMANCE REQUIREMENTS |
| BS EN 61347-2-6:2001 | Lamp controlgear Particular requirements for d.c. supplied electronic ballasts for aircraft lighting |
| BS EN 61347-2-3:2011 | Lamp control gear Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps |
| BS EN 61347-2-1 : 2001 | LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) |
| I.S. EN 62733:2015 | PROGRAMMABLE COMPONENTS IN ELECTRONIC LAMP CONTROLGEAR - GENERAL AND SAFETY REQUIREMENTS |
| I.S. EN 60079-15:2010 | EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N' |
| CEI EN 61347-2-3 : 2012 | LAMP CONTROLGEAR - PART 2-3: PARTICULAR REQUIREMENTS FOR A.C. AND/OR D.C. SUPPLIED ELECTRONIC CONTROL GEAR FOR FLUORESCENT LAMPS |
| UNE-EN 62532:2011 | Fluorescent induction lamps - Safety specifications |
| BS EN 61347-2-7:2012 | Lamp controlgear Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| I.S. EN 62718:2016 | RAILWAY APPLICATIONS - ROLLING STOCK - DC SUPPLIED ELECTRONIC BALLASTS FOR LIGHTING FLUORESCENT LAMPS |
| CEI EN 60079-15 : 2012 | EXPLOSIVE ATMOSPHERES - PART 15: EQUIPMENT PROTECTION BY TYPE OF PROTECTION 'N' |
| CEI EN 61347-2-11 : 2002 | LAMP CONTROLGEAR - PART 2-11: PARTICULAR REQUIREMENTS FOR MISCELLANEOUS ELECTRONIC CIRCUITS USED WITH LUMINAIRES |
| I.S. EN 62442-3:2014 | ENERGY PERFORMANCE OF LAMP CONTROLGEAR - PART 3: CONTROLGEAR FOR HALOGEN LAMPS AND LED MODULES - METHOD OF MEASUREMENT TO DETERMINE THE EFFICIENCY OF THE CONTROLGEAR |
| I.S. EN 62031:2008 | LED MODULES FOR GENERAL LIGHTING - SAFETY SPECIFICATIONS (IEC 62031:2008 (EQV)) |
| EN 60079-15:2010 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| VDE 0712-35 : 2001 COR 2 2011 | LAMP CONTROLGEAR - PART 2-5: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR PUBLIC TRANSPORT LIGHTING |
| VDE 0712-34 : 2001 COR 2 2011 | LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING |
| BS EN 60968:2015 | Self-ballasted fluorescent lamps for general lighting services. Safety requirements |
| UNE-EN 62718:2016 | Railway applications - Rolling stock - DC supplied electronic ballasts for lighting fluorescent lamps |
| BS EN 62442-3:2014 | Energy performance of lamp controlgear Controlgear for halogen lamps and LED modules. Method of measurement to determine the efficiency of the controlgear |
| CEI EN 62386-101 : 2016 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 101: GENERAL REQUIREMENTS - SYSTEM COMPONENTS |
| BS EN 61347-2-2:2012 | Lamp controlgear Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
| BS EN 62811:2015 | AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps). Performance requirements for low frequency squarewave operation |
| BS EN 60730-2-3:2007 | Automatic electrical controls for household and similar use Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps |
| BS EN 61347-2-10 : 2001 | LAMP CONTROLGEAR - PART 2-10: PARTICULAR REQUIREMENTS FOR ELECTRONIC INVERTORS AND CONVERTORS FOR HIGH-FREQUENCY OPERATION OF COLD TUBULAR DISCHARGE LAMPS (NEON TUBES) |
| BS EN 62386-203:2009 | Digital addressable lighting interface Particular requirements for control gear. Discharge lamps (excluding fluorescent lamps) (device type 2) |
| I.S. EN IEC 62386-332:2018 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 332: PARTICULAR REQUIREMENTS - INPUT DEVICES - FEEDBACK |
| I.S. EN 61347-2-11:2001 | LAMP CONTROLGEAR - PART 2-11: PARTICULAR REQUIREMENTS FOR MISCELLANEOUS ELECTRONIC CIRCUITS USED WITH LUMINAIRES (IEC 61347-2-11:2001 (EQV)) |
| UNE-EN 61347-2-3:2012 | Lamp control gear - Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps |
| BS EN 50107-2:2005 | Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV Requirements for earth-leakage and open-circuit protective devices |
| I.S. EN 60079-7:2015 | EXPLOSIVE ATMOSPHERES - PART 7: EQUIPMENT PROTECTION BY INCREASED SAFETY 'E' |
| I.S. EN 61047:2004 | DC OR AC SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS - PERFORMANCE REQUIREMENTS |
| BS EN 62442-2:2014 | Energy performance of lamp controlgear Controlgear for high intensity discharge lamps (excluding fluorescent lamps). Method of measurement to determine the efficiency of the controlgear |
| I.S. EN 60968:2015 | SELF-BALLASTED FLUORESCENT LAMPS FOR GENERAL LIGHTING SERVICES - SAFETY REQUIREMENTS |
| I.S. EN 60921:2005 | BALLASTS FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| EN 62442-2:2014/A11:2017 | ENERGY PERFORMANCE OF LAMP CONTROLGEAR - PART 2: CONTROLGEAR FOR HIGH INTENSITY DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - METHOD OF MEASUREMENT TO DETERMINE THE EFFICIENCY OF THE CONTROLGEAR |
| I.S. EN 62776:2015 | DOUBLE-CAPPED LED LAMPS DESIGNED TO RETROFIT LINEAR FLUORESCENT LAMPS - SAFETY SPECIFICATIONS |
| I.S. EN 61347-2-1:2004 | LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) |
| BS EN 62386-103:2014+A1:2018 | Digital addressable lighting interface General requirements. Control devices |
| BS EN 60079-15:2010 | Explosive atmospheres Equipment protection by type of protection \'n\' |
| EN 62931:2017 | GX16t-5 capped tubular led lamp - Safety specifications |
| PREN 50107-3 : DRAFT 2016 | PRODUCT STANDARD COVERING LUMINOUS SIGNS WITH DISCHARGE LAMPS AND/OR LED (LIGHT EMITTING DIODES) AND/OR EL (ELECTROLUMINESCENT) LIGHTSOURCES WITH A NOMINAL VOLTAGE NOT EXCEEDING 1000 V, WITH THE EXCLUSION OF GENERAL LIGHTING, TRAFFIC- OR EMERGENCY RELATED PURPOSE |
| UNI EN 12665 : 2011 | LIGHT AND LIGHTING - BASIC TERMS AND CRITERIA FOR SPECIFYING LIGHTING REQUIREMENTS |
| EN 62386-101:2014 | Digital addressable lighting interface - Part 101: General requirements - System components |
| UNE-EN 61347-2-13:2015 | Lamp controlgear - Part 2-13: Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules |
| CEI EN 62931 : 1ED 2017 | GX16T-5 CAPPED TUBULAR LED LAMP - SAFETY SPECIFICATIONS |
| BS EN 62386-208:2009 | Digital addressable lighting interface Particular requirements for control gear. Switching function (device type 7) |
| BS EN 62031 : 2008 | LED MODULES FOR GENERAL LIGHTING - SAFETY SPECIFICATIONS |
| CEI EN 61347-2-9 : 2013 | LAMP CONTROLGEAR - PART 2-9: PARTICULAR REQUIREMENTS FOR ELECTROMAGNETIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) |
| BS EN 62386-209:2011 | Digital addressable lighting interface Particular requirements for control gear. Colour control (device type 8) |
| BS EN 62041:2010 | Safety of transformers, reactors, power supply units and combinations thereof. EMC requirements |
| I.S. EN 61347-2-9:2013 | LAMP CONTROLGEAR - PART 2-9: PARTICULAR REQUIREMENTS FOR ELECTROMAGNETIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) (IEC 61347-2-9:2012 (EQV)) |
| I.S. EN 61347-2-5:2001 | LAMP CONTROLGEAR - PART 2-5: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR PUBLIC TRANSPORT LIGHTING (IEC 61347-2-5:2000 (EQV)) |
| UNE-EN 61347-2-7:2012 | Lamp controlgear -- Part 2-7: Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| BS EN 62386-101:2014 | Digital addressable lighting interface General requirements. System components |
| I.S. EN 62532:2011 | FLUORESCENT INDUCTION LAMPS - SAFETY SPECIFICATIONS |
| I.S. EN 61347-2-10:2001 | LAMP CONTROLGEAR - PART 2-10: PARTICULAR REQUIREMENTS FOR ELECTRONIC INVERTORS AND CONVERTORS FOR HIGH-FREQUENCY OPERATION OF COLD START TUBULAR DISCHARGE LAMPS (NEON TUBES) (IEC 61347-2-10:2000 (EQV)) |
| I.S. EN 61347-2-7:2012 | LAMP CONTROLGEAR - PART 2-7: PARTICULAR REQUIREMENTS FOR BATTERY SUPPLIED ELECTRONIC CONTROLGEAR FOR EMERGENCY LIGHTING (SELF-CONTAINED) (IEC 61347-2-7:2011 (EQV)) |
| BS EN 61347-2-5:2001 | Lamp controlgear Particular requirements for d.c. supplied electronic ballasts for public transport lighting |
| BS EN 55015 : 2013 | LIMITS AND METHODS OF MEASUREMENT OF RADIO DISTURBANCE CHARACTERISTICS OF ELECTRICAL LIGHTING AND SIMILAR EQUIPMENT |
| BS EN 61347-2-7:2012+A1:2019 | Lamp controlgear Particular requirements for battery supplied electronic controlgear for emergency lighting (self-contained) |
| CEI EN 60730-2-3 : 2008 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| CEI EN 61047 : 2005 | DC OR AC SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS - PERFORMANCE REQUIREMENTS |
| I.S. EN 62034:2012 | AUTOMATIC TEST SYSTEMS FOR BATTERY POWERED EMERGENCY ESCAPE LIGHTING (IEC 62034:2012 (EQV)) |
| BS EN 61347-2-13 : 2014 | LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES (IEC 61347-2-13:2014) |
| BS EN 62838:2016 | LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. Safety specifications |
| EN 62031:2008/A2:2015 | LED MODULES FOR GENERAL LIGHTING - SAFETY SPECIFICATIONS (IEC 62031:2008/A2:2014) |
| UNE-EN 62838:2016 | LEDsi lamps for general lighting services with supply voltages not exceeding 50 v a.c. r.m.s. or 120 v ripple free D.C. - Safety specifications |
| UNE-EN 12665:2012 | Light and lighting - Basic terms and criteria for specifying lighting requirements |
| BS EN 12665:2011 | Light and lighting. Basic terms and criteria for specifying lighting requirements |
| UNE-EN 60929:2011 | AC and/or DC-supplied electronic control gear for tubular fluorescent lamps - Performance requirements |
| UNE-EN 62560:2013 | Self-ballasted LED-lamps for general lighting services by voltage > 50 V - Safety specifications |
| EN 60923:2005/A1:2006 | AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS |
| I.S. EN 61347-2-8:2001 | LAMP CONTROLGEAR - PART 2-8: PARTICULAR REQUIREMENTS FOR BALLASTS FOR FLUORESCENT LAMPS (IEC 61347-2-8:2000 (EQV)) |
| UNE-EN 60079-15:2013 | Explosive atmospheres - Part 15: Equipment protection by type of protection "n" |
| 01/206090 DC : DRAFT OCT 2001 | EN 50107-2 - SIGNS AND LUMINOUS-DISCHARGE-TUBE INSTALLATIONS OPERATING FROM A NO-LOAD RATED OUTPUT VOLTAGE EXCEEDING 1 KV BUT NOT EXCEEDING 10 KV - PART 2: REQUIREMENTS FOR EARTH-LEAKAGE AND OPEN-CIRCUIT PROTECTIVE DEVICES |
| I.S. EN IEC 61347-2-14:2018 | LAMP CONTROLGEAR - PART 2-14: PARTICULAR REQUIREMENTS FOR DC AND/OR AC SUPPLIED ELECTRONIC CONTROLGEAR FOR FLUORESCENT INDUCTION LAMPS |
| UNE-EN 61347-2-2:2012 | Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
| BS EN 61347-2-4:2001 | Lamp controlgear Particular requirements for d.c. supplied electronic ballasts for general lighting |
| BS EN 62931:2017 | GX16t-5 capped tubular led lamp. Safety specifications |
| BS EN 62776:2015 | Double-capped LED lamps designed to retrofit linear fluorescent lamps. Safety specifications |
| CEI EN 61347-2-7 : 2012 | LAMP CONTROLGEAR - PART 2-7: PARTICULAR REQUIREMENTS FOR BATTERY SUPPLIED ELECTRONIC CONTROLGEAR FOR EMERGENCY LIGHTING (SELF-CONTAINED) |
| BS EN 62386-206:2009 | Digital addressable lighting interface Particular requirements for control gear. Conversion from digital signal into d.c. voltage (device type 5) |
| BS EN 62386-204:2009 | Digital addressable lighting interface Particular requirements for control gear. Low voltage halogen lamps (device type 3) |
| CEI EN 62811 : 2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROLGEAR FOR DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS FOR LOW FREQUENCY SQUAREWAVE OPERATION |
| I.S. EN 60927:2008 | AUXILIARIES FOR LAMPS - STARTING DEVICES (OTHER THAN GLOW STARTERS) - PERFORMANCE REQUIREMENTS |
| BS EN 62532 : 2011 | FLUORESCENT INDUCTION LAMPS - SAFETY SPECIFICATIONS |
| I.S. EN 62442-2:2014 | ENERGY PERFORMANCE OF LAMP CONTROLGEAR - PART 2: CONTROLGEAR FOR HIGH INTENSITY DISCHARGE LAMPS (EXCLUDING FLUORESCENT LAMPS) - METHOD OF MEASUREMENT TO DETERMINE THE EFFICIENCY OF THE CONTROLGEAR |
| BS EN 62560:2012+A11:2019 | Self-ballasted LED-lamps for general lighting services by voltage > 50 V. Safety specifications |
| UNE-EN 62776:2015 | Double-capped LED lamps designed to retrofit linear fluorescent lamps - Safety specifications |
| I.S. EN 61347-2-3:2011 | LAMP CONTROL GEAR - PART 2-3: PARTICULAR REQUIREMENTS FOR A.C. AND/OR D.C. SUPPLIED ELECTRONIC CONTROL GEAR FOR FLUORESCENT LAMPS |
| EN IEC 62386-332:2018 | Digital addressable lighting interface - Part 332: Particular requirements - Input devices - Feedback |
| EN 62442-3:2014/A11:2017 | ENERGY PERFORMANCE OF LAMP CONTROLGEAR - PART 3: CONTROLGEAR FOR HALOGEN LAMPS AND LED MODULES - METHOD OF MEASUREMENT TO DETERMINE THE EFFICIENCY OF THE CONTROLGEAR |
| I.S. EN 62838:2016 | LEDSI LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES NOT EXCEEDING 50 V A.C. R.M.S. OR 120 V RIPPLE FREE D.C. - SAFETY SPECIFICATIONS |
| I.S. EN 61347-2-13:2014 | LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES |
| UNE-EN 60079-7:2016 | Explosive atmospheres - Part 7: Equipment protection by increased safety "e" |
| I.S. EN 12665:2011 | LIGHT AND LIGHTING - BASIC TERMS AND CRITERIA FOR SPECIFYING LIGHTING REQUIREMENTS |
| I.S. EN 60730-2-3:2007 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| EN 62532:2011/A1:2017 | FLUORESCENT INDUCTION LAMPS - SAFETY SPECIFICATIONS |
| EN 62386-210:2011 | Digital addressable lighting interface - Part 210: Particular requirements for control gear - Sequencer (device type 9) |
| EN 62386-208:2009 | Digital addressable lighting Interface - Part 208: Particular requirements for control gear - Switching function (device type 7) |
| EN 60921:2004/A1:2006 | BALLASTS FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| EN 62386-202 : 2009 | DIGITAL ADDRESSABLE LIGHTING INTERFACE - PART 202: PARTICULAR REQUIREMENTS FOR CONTROL GEAR - SELF-CONTAINED EMERGENCY LIGHTING (DEVICE TYPE 1) |
| EN 60730-2-3:2007 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| EN 62041:2010 | Safety of transformers, reactors, power supply units and combinations thereof - EMC requirements |
| EN 61347-2-10:2001/corrigendum:2010 | LAMP CONTROLGEAR - PART 2-10: PARTICULAR REQUIREMENTS FOR ELECTRONIC INVERTORS AND CONVERTORS FOR HIGH-FREQUENCY OPERATION OF COLD TUBULAR DISCHARGE LAMPS (NEON TUBES) (IEC 61347-2-10:2000/A1:2008) |
| EN 50107-2:2005 | Signs and luminous-discharge-tube installations operating from a no-load rated output voltage exceeding 1 kV but not exceeding 10 kV - Part 2: Requirements for earth-leakage and open-circuit protective devices |
| EN 62386-203:2009 | Digital addressable lighting interface - Part 203: Particular requirements for control gear - Discharge lamps (excluding fluorescent lamps) (device type 2) |
| EN 62034:2012 | Automatic test systems for battery powered emergency escape lighting |
| EN 61347-2-1:2001/A2:2014 | LAMP CONTROLGEAR - PART 2-1: PARTICULAR REQUIREMENTS FOR STARTING DEVICES (OTHER THAN GLOW STARTERS) (IEC 61347-2-1:2000/A2:2013) |
| EN 60929:2011/A1:2016 | AC AND/OR DC-SUPPLIED ELECTRONIC CONTROL GEAR FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| EN 62386-206:2009 | Digital addressable lighting interface - Part 206: Particular requirements for control gear - Conversion from digital signal into d. c. voltage (device type 5) |
| EN 61347-2-4:2001/corrigendum:2010 | LAMP CONTROLGEAR - PART 2-4: PARTICULAR REQUIREMENTS FOR D.C. SUPPLIED ELECTRONIC BALLASTS FOR GENERAL LIGHTING |
| EN 61347-2-3:2011/A1:2017 | LAMP CONTROL GEAR - PART 2-3: PARTICULAR REQUIREMENTS FOR A.C. AND/OR D.C. SUPPLIED ELECTRONIC CONTROL GEAR FOR FLUORESCENT LAMPS (IEC 61347-2-3:2011/A1:2016) |
| EN 61047:2004 | DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements |
| EN 62811:2015 | AC and/or DC-supplied electronic controlgear for discharge lamps (excluding fluorescent lamps) - Performance requirements for low frequency squarewave operation |
| UNE-HD 60364-5-559:2013 | Low-voltage electrical installations - Part 5-559: Selection and erection of electrical equipment - Luminaires and lighting installations |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 60906-3:1994 | IEC System of plugs and socket-outlets for household and similar purposes - Part 3: SELV plugs and socket-outlets, 16 A 6V, 12 V, 24 V, 48 V, a.c. and d.c. |
| IEC 60038:2009 | IEC standard voltages |
| IEC 60730-2-3:2006 | Automatic electrical controls for household and similar use - Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| IEC 60384-14:2013+AMD1:2016 CSV | Fixed capacitors for use in electronic equipment - Part 14: Sectional specification - Fixed capacitors for electromagnetic interference suppression and connection to the supply mains |
| EN 61347-2-9:2013 | Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
| EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
| EN 60085:2008 | Electrical insulation - Thermal evaluation and designation |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| EN 61558-1:2005/A1:2009 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| IEC 61347-2-9:2012 | Lamp controlgear - Part 2-9: Particular requirements for electromagnetic controlgear for discharge lamps (excluding fluorescent lamps) |
| IEC TR 60083:2015 | Plugs and socket-outlets for domestic and similar general use standardized in member countries of IEC |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| EN 60691:2016 | Thermal-links - Requirements and application guide |
| IEC 60929:2011+AMD1:2015 CSV | AC and/or DC-supplied electronic control gear for tubularfluorescent lamps - Performance requirements |
| IEC 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| EN 60216 : 1990 | |
| IEC 61047:2004 | DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements |
| IEC 62384:2006+AMD1:2009 CSV | DC or AC supplied electronic control gear for LED modules - Performance requirements |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| IEC 61347-2-1:2000+AMD1:2005+AMD2:2013 CSV | Lamp controlgear - Part 2-1: Particular requirements for startingdevices (other than glow starters) |
| EN 60923:2005/A1:2006 | AUXILIARIES FOR LAMPS - BALLASTS FOR DISCHARGE LAMPS (EXCLUDING TUBULAR FLUORESCENT LAMPS) - PERFORMANCE REQUIREMENTS |
| EN 60317-0-1:2014 | Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEC 60925:1989+AMD1:1996+AMD2:2001 CSV | DC supplied electronic ballasts for tubular fluorescent lamps - Performance requirements |
| EN 60921:2004/A1:2006 | BALLASTS FOR TUBULAR FLUORESCENT LAMPS - PERFORMANCE REQUIREMENTS |
| IEC 60921:2004+AMD1:2006 CSV | Ballasts for tubular fluorescent lamps - Performance requirements |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| IEC 60901:1996+AMD1:1997+AMD2:2000 CSV | Single-capped fluorescent lamps - Performance specifications |
| IEC 60317-0-1:2013 | Specifications for particular types of winding wires - Part 0-1: General requirements - Enamelled round copper wire |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEEE 101 : 1987 | GUIDE FOR THE STATISTICAL ANALYSIS OF THERMAL LIFE TEST DATA |
| EN 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60691:2015 | Thermal-links - Requirements and application guide |
| IEC 60598-1:2014+AMD1:2017 CSV | Luminaires - Part 1: General requirements and tests |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60730-2-3:2007 | AUTOMATIC ELECTRICAL CONTROLS FOR HOUSEHOLD AND SIMILAR USE - PART 2-3: PARTICULAR REQUIREMENTS FOR THERMAL PROTECTORS FOR BALLASTS FOR TUBULAR FLUORESCENT LAMPS |
| IEC 61347-2-2:2011 | Lamp controlgear - Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps |
| IEC 60927:2007+AMD1:2013 CSV | Auxiliaries for lamps - Starting devices (other than glow starters)- Performance requirements |
| HD 193 : 200S2 | VOLTAGE BANDS FOR ELECTRICAL INSTALLATIONS OF BUILDINGS |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 60884-2-4:2007 | Plugs and socket-outlets for household and similar purposes - Part 2-4: Particular requirements for plugs and socket-outlets for SELV |
| EN 60901:1996/A6:2017 | SINGLE-CAPPED FLUORESCENT LAMPS - PERFORMANCE SPECIFICATIONS (IEC 60901:1996/A6:2014, MODIFIED) |
| EN 61558-2-6:2009 | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| EN 60664-4:2006/corrigendum:2006 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS |
| ISO 4046-4:2002 | Paper, board, pulps and related terms Vocabulary Part 4: Paper and board grades and converted products |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| IEC 60155:1993 | Glow-starters for fluorescent lamps |
| EN 60695-11-5:2017 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 60923:2005+AMD1:2006 CSV | Auxiliaries for lamps - Ballasts for discharge lamps (excluding tubular fluorescent lamps) - Performance requirements |
| IEC 60695-11-5 : 2.0 | FIRE HAZARD TESTING - PART 11-5: TEST FLAMES - NEEDLE-FLAME TEST METHOD - APPARATUS, CONFIRMATORY TEST ARRANGEMENT AND GUIDANCE |
| IEC 60695-11-5:2016 | Fire hazard testing - Part 11-5: Test flames - Needle-flame test method - Apparatus, confirmatory test arrangement and guidance |
| IEC 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| HD 243 : S12 | GRAPHICAL SYMBOLS FOR USE ON EQUIPMENT - INDEX, SURVEY AND COMPILATION OF THE SINGLE SHEETS |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60068-2-14:2009 | Environmental testing - Part 2-14: Tests - Test N: Change of temperature |
| IEC 61189-2:2006 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures |
| IEC 61347-2-8:2000+AMD1:2006 CSV | Lamp controlgear - Part 2-8: Particular requirements for ballasts for fluorescent lamps |
| EN 61180-1:1994 | High-voltage test techniques for low-voltage equipment - Part 1: Definitions, test and procedure requirements |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| EN 61189-2:2006 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.