EN 61800-5-1:2007/A1:2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
Superseded date
02-13-2021
Published date
01-12-2013
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Protection against electric shock,
thermal, and energy hazards
5 Test requirements
6 Information and marking requirements
Annex A (informative) - Examples of protection
in case of direct contact
Annex B (informative) - Examples of overvoltage
category reduction
Annex C (normative) - Measurement of clearance
and creepage distances
Annex D (informative) - Altitude correction for clearances
Annex E (informative) - Clearance and creepage distance
determination for frequencies greater than 30 kHz
Annex F (informative) - Cross-sections of round conductors
Annex G (informative) - Guidelines for RCD compatibility
Annex H (informative) - Symbols referred to in this part of
IEC 61800
Bibliography
Describes requirements for adjustable speed power drive systems, or their elements, with respect to electrical, thermal and energy safety considerations.
| Committee |
TC 22X
|
| DocumentType |
Standard
|
| PublisherName |
European Committee for Standards - Electrical
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| PN EN 61800-5-1 : 2007 AMD 1 2017 | Identical |
| NEN EN IEC 61800-5-1 : 2007 AMD 1 2017 | Identical |
| VDE 0160-105-1 : 2017 | Identical |
| BS EN 61800-5-1:2007 | Identical |
| NBN EN 61800-5-1 : 2008 | Identical |
| DIN EN 61800-5-1 : 2017 | Identical |
| SN EN 61800-5-1 : 2007 AMD 1 2017 | Identical |
| UNE-EN 61800-5-1:2007/A1:2017 | Identical |
| I.S. EN 61800-5-1:2007 | Identical |
| I.S. EN 61800-5-1:2007/A1:2017 | Identical |
| BS EN 61800-5-1:2007+A1:2017 | Identical |
| NF EN 61800 5-1 : 2007 | Identical |
| OVE/ONORM EN 61800-5-1 : 2014 | Identical |
| DIN EN 1034-21:2012-11 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| DIN EN 1034-21 E : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| CEI 301-3 : 2005 | GUIDE FOR THE CHARACTERISATION AND IDENTIFICATION OF VARIABLE SPEED ELECTRICAL DRIVES BY MEANS OF A PLATE |
| 12/30243081 DC : 0 | BS EN 1034-17 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES |
| S.R. CLC/TR 50646:2015 | RAILWAY APPLICATION - FIXED INSTALLATIONS - SPECIFICATION FORREVERSIBLE D.C. SUBSTATIONS |
| I.S. EN 1034-16:2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES |
| 12/30243084 DC : 0 | BS EN 1034-21 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| PD CLC/TR 50646:2015 | Railway Application. Fixed Installations. Specification for reversible d.c. substations |
| DIN EN 1034-16:2012-06 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES |
| I.S. EN 15571:2014 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES |
| VDE 0160-109-2 : 2018-01 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017) |
| UNI EN 1034-21 : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| EN 1034-17:2012 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines |
| EN 1034-21:2012 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 21: Coating machines |
| EN 61800-5-2:2017 | Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional |
| DIN EN 15571:2015-03 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| BS EN 1034-16:2012 | Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Paper and board making machines |
| EN 61800-2:2015 | Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems |
| I.S. CLC TS 60034-25:2005 | ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY |
| I.S. EN 60146-1-1:2010 | SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS |
| EN 15571:2014 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| BS EN 15571:2014 | Machines and plants for mining and tooling of natural stone. Safety. Requirements for surface finishing machines |
| 11/30243078 DC : 0 | BS EN 1034-16 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES |
| BS EN 1034-17:2012 | Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Tissue making machines |
| BS EN 1034-21:2012 | Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Coating machines |
| I.S. EN 1034-21:2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES |
| UNI EN 1034-16 : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES |
| DIN EN 61800-9-2 : 2018-01 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017) |
| S.R. CLC/TS 60034-25:2008 | ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY |
| DIN EN 15571 E : 2015 | MACHINES AND PLANTS FOR MINING AND TOOLING OF NATURAL STONE - SAFETY - REQUIREMENTS FOR SURFACE FINISHING MACHINES |
| DIN EN 1034-17 E : 2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES |
| DIN EN 1034-17:2012-11 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines |
| BS EN 61800-5-2:2017 | Adjustable speed electrical power drive systems Safety requirements. Functional |
| CEI EN 61800-5-2 : 2009 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL |
| CEI EN 60146-1-1 : 2013 | SEMICONDUCTOR CONVERTERS - GENERAL REQUIREMENTS AND LINE COMMUTATED CONVERTERS - PART 1-1: SPECIFICATION OF BASIC REQUIREMENTS |
| BS EN 60204-33:2011 | Safety of machinery. Electrical equipment of machines Requirements for semiconductor fabrication equipment |
| BS EN 61800-2:2015 | Adjustable speed electrical power drive systems General requirements. Rating specifications for low voltage adjustable speed a.c. power drive systems |
| BS EN 50598-2 : 2014 | ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS |
| UNE-EN 15571:2015 | Machines and plants for mining and tooling of natural stone - Safety - Requirements for surface finishing machines |
| UNE-EN 50598-2:2015 | Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 2: Energy efficiency indicators for power drive systems and motor starters |
| BS EN 60146-1-1:2010 | Semiconductor converters. General requirements and line commutated converters Specification of basic requirements |
| I.S. EN 1034-17:2012 | SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES |
| I.S. EN 50598-2:2014 | ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS |
| I.S. EN 60204-33:2011 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT |
| I.S. EN 61800-5-2:2017 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL |
| I.S. EN 61800-2:2015 | ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 2: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR LOW VOLTAGE ADJUSTABLE SPEED A.C. POWER DRIVE SYSTEMS |
| EN 1034-16:2012 | Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 16: Paper and board making machines |
| EN 60146-1-1:2010 | Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements |
| EN 60204-33:2011 | Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment |
| EN 50598-2:2014/A1:2016 | ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS |
| CLC/TS 60034-25:2008 | Rotating electrical machines - Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply |
| CLC/TR 50646:2015 | Railway Application - Fixed Installations - Specification for reversible d.c. substations |
| IEC 60695-11-20:2015 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test method |
| IEC 60112:2003+AMD1:2009 CSV | Method for the determination of the proof and the comparative tracking indices of solid insulating materials |
| IEC 61800-3:2017 | Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods |
| IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
| IEC 61800-2:2015 | Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems |
| IEC 61800-4:2002 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| IEC 60947-7-2:2009 | Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors |
| IEC 60664-4:2005 | Insulation coordination for equipment within low-voltage systems - Part 4: Consideration of high-frequency voltage stress |
| IEC 60034-9:2003+AMD1:2007 CSV | Rotating electrical machines - Part 9: Noise limits |
| IEC 60050-195:1998 | International Electrotechnical Vocabulary (IEV) - Part 195: Earthing and protection against electric shock |
| IEC 60947-4-1:2009+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 4-1: Contactors and motor-starters - Electromechanical contactors and motor-starters |
| EN 60034-1:2010/corrigendum Oct. 2010 | ROTATING ELECTRICAL MACHINES - PART 1: RATING AND PERFORMANCE |
| IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
| IEC 60050-601:1985 | International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
| EN 61230:2008 | LIVE WORKING - PORTABLE EQUIPMENT FOR EARTHING OR EARTHING AND SHORT-CIRCUITING |
| IEC 60050-151:2001 | International Electrotechnical Vocabulary (IEV) - Part 151: Electrical and magnetic devices |
| EN 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60050-441:1984 | International Electrotechnical Vocabulary (IEV) - Part 441: Switchgear, controlgear and fuses |
| IEC 61643-12:2008 | Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles |
| EN 62271-102:2002/AC:2014 | HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 102: ALTERNATING CURRENT DISCONNECTORS AND EARTHING SWITCHES (IEC 62271-102:2001/A2:2013) |
| HD 60364-5-54:2011/A11:2017 | LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS |
| IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
| IEC 60695-2-11:2014 | Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-wire flammability test method for end-products (GWEPT) |
| IEC 62103:2003 | Electronic equipment for use in power installations |
| IEC 60947-7-1:2009 | Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors |
| HD 588.1 : S1 AMD 1 | HIGH VOLTAGE TEST TECHNIQUES - GENERAL DEFINITIONS AND TEST REQUIREMENTS |
| IEC 60050-551:1998 | International Electrotechnical Vocabulary (IEV) - Part 551: Power electronics |
| IEC 60050-442:1998 | International Electrotechnical Vocabulary (IEV) - Part 442: Electrical accessories |
| IEC 60364-1:2005 | Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general characteristics, definitions |
| IEC 60695-2-13:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-13: Glowing/hot-wire based test methods- Glow-wire ignition temperature (GWIT) test method for materials |
| EN 60112 : 2003 AMD 1 2009 | METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
| EN 60695-2-13:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014) |
| IEC 60695-2-12:2010+AMD1:2014 CSV | Fire hazard testing - Part 2-12: Glowing/hot-wire based test methods- Glow-wire flammability index (GWFI) test method for materials |
| IEC 60146-1-1:2009 | Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements |
| EN 61800-2:2015 | Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60755:2017 | General safety requirements for residual current operated protective devices |
| EN 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 60364-4-44:2007+AMD1:2015 CSV | Low-voltage electrical installations - Part 4-44: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances |
| IEC 60068-2-2:2007 | Environmental testing - Part 2-2: Tests - Test B: Dry heat |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| IEC 61230:2008 | Live working - Portable equipment for earthing or earthing and short-circuiting |
| IEC 62079:2001 | Preparation of instructions - Structuring, content and presentation |
| IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
| IEC 62020:1998+AMD1:2003 CSV | Electrical accessories - Residual current monitors for household and similar uses (RCMs) |
| EN 60204-11:2000/corrigendum:2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV |
| EN 60068-2-78:2013 | Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state |
| IEC 60071-2:1996 | Insulation co-ordination - Part 2: Application guide |
| EN 60068-2-6:2008 | Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal) |
| IEC 60050-826:2004 | International Electrotechnical Vocabulary (IEV) - Part 826: Electrical installations |
| IEC 60664-3:2016 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 62477-1:2012+AMD1:2016 CSV | Safety requirements for power electronic converter systems and equipment - Part 1: General |
| IEC 60050-111:1996 | International Electrotechnical Vocabulary (IEV) - Part 111: Physics and chemistry |
| IEC 61180-1:1992 | High-voltage test techniques for low voltage equipment - Part 1: Definitions, test and procedure requirements |
| EN 61800-4:2003 | Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV |
| EN 60664-4:2006/corrigendum:2006 | INSULATION COORDINATION FOR EQUIPMENT WITHIN LOW-VOLTAGE SYSTEMS - PART 4: CONSIDERATION OF HIGH-FREQUENCY VOLTAGE STRESS |
| EN 60529:1991/AC:2016-12 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015) |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| EN 60947-7-1:2009 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 7-1: ANCILLARY EQUIPMENT - TERMINAL BLOCKS FOR COPPER CONDUCTORS |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| IEC 60695-2-10:2013 | Fire hazard testing - Part 2-10: Glowing/hot-wire based test methods - Glow-wire apparatus and common test procedure |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
| EN 60664-3:2017 | Insulation coordination for equipment within low-voltage systems - Part 3: Use of coating, potting or moulding for protection against pollution |
| IEC 61189-2:2006 | Test methods for electrical materials, printed boards and other interconnection structures and assemblies - Part 2: Test methods for materials for interconnection structures |
| IEC 60990:2016 | Methods of measurement of touch current and protective conductor current |
| IEC 61800-1:1997 | Adjustable speed electrical power drive systems - Part 1: General requirments - Rating specifications for low voltage adjustables speed d.c. power drive systems |
| EN 60034-5:2001/A1:2007 | ROTATING ELECTRICAL MACHINES - PART 5: DEGREES OF PROTECTION PROVIDED BY THE INTEGRAL DESIGN OF ROTATING ELECTRICAL MACHINES (IP CODE) - CLASSIFICATION |
| IEC 62271-102:2001+AMD1:2011+AMD2:2013 CSV | High-voltage switchgear and controlgear - Part 102: Alternatingcurrent disconnectors and earthing switches |
| EN 61800-1:1998 | Adjustable speed electrical power drive systems - Part 1: General requirements - Rating specifications for low voltage adjustable speed d.c. power drive systems |
| EN 60947-7-2:2009 | Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors |
| EN 60990:2016 | Methods of measurement of touch current and protective conductor current |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.