• There are no items in your cart

EN 61854:1998

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Overhead lines - Requirements and tests for spacers
Superseded date

04-23-2020

Published date

10-12-1998

FOREWORD
1 Scope
2 Normative references
3 Definitions
4 General requirements
  4.1 Design
  4.2 Materials
      4.2.1 General
      4.2.2 Non-metallic materials
  4.3 Mass, dimensions and tolerances
  4.4 Protection against corrosion
  4.5 Manufacturing appearance and finish
  4.6 Marking
  4.7 Installation instructions
5 Quality assurance
6 Classification of tests
  6.1 Type tests
      6.1.1 General
      6.1.2 Application
  6.2 Sample tests
      6.2.1 General
      6.2.2 Application
      6.2.3 Sampling and acceptance criteria
  6.3 Routine tests
      6.3.1 General
      6.3.2 Application and acceptance criteria
  6.4 Table of tests to be applied
7 Test methods
  7.1 Visual examination
  7.2 Verification of dimensions, materials and mass
  7.3 Corrosion protection test
      7.3.1 Hot dip galvanized components (other than
            stranded galvanized steel wires)
      7.3.2 Ferrous components protected from corrosion by
            methods other than hot dip galvanizing
      7.3.3 Stranded galvanized steel wires
      7.3.4 Corrosion caused by non-metallic components
  7.4 Non-destructive tests
  7.5 Mechanical tests
      7.5.1 Clamp slip tests
            7.5.1.1 Longitudinal slip test
            7.5.1.2 Torsional slip test
      7.5.2 Breakaway bolt test
      7.5.3 Clamp bolt tightening test
      7.5.4 Simulated short-circuit current test and
            compression and tension tests
            7.5.4.1 Simulated short-circuit current test
            7.5.4.2 Compression and tension test
      7.5.5 Characterisation of the elastic and damping
            properties
      7.5.6 Flexibility tests
      7.5.7 Fatigue tests
            7.5.7.1 General
            7.5.7.2 Subspan oscillation
            7.5.7.3 Aeolian vibration
  7.6 Tests to characterise elastomers
      7.6.1 General
      7.6.2 Tests
      7.6.3 Ozone resistance test
  7.7 Electrical tests
      7.7.1 Corona and radio interference voltage (RIV)
            tests
      7.7.2 Electrical resistance test
  7.8 Verification of vibration behaviour of the
      bundle-spacer system
Annex A (normative) Minimum technical details to be agreed
                    between purchaser and supplier
Annex B (informative) Compressive forces in the simulated
                      short-circuit current test
Annex C (informative) Characterisation of the elastic and
                      damping properties Stiffness-Damping Method
Annex D (informative) Verification of vibration behaviour of
                      bundle/spacer system
Annex ZA (normative) Normative references to international
                     publications with their corresponding
                     European publications
Bibliography
Figures
Tables

Applies to spacers for conductor bundles of overhead lines. It covers rigid spacers, flexible spacers and spacer dampers. It does not apply to interphase spacers, hoop spacers and bonding spacers.

Committee
CLC/TC 11
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
SupersededBy

Standards Relationship
OVE/ONORM EN 61854 : 1999 Identical
PN EN 61854 : 2003 Identical
UNE-EN 61854:1999 Identical
I.S. EN 61854:1999 Identical
NBN EN 61854 : 1999 Similar to
BS EN 61854:1998 Identical
CEI EN 61854 : 2000 Identical
VDE 0212-2 : 1999 Identical
DIN EN 61854 : 1999 Identical
NF EN 61854 : 2001 Identical
SN EN 61854 : 1998 Identical
NEN EN IEC 61854 : 1999 Identical
IEC 61854:1998 Identical

UNE-EN 50341-1:2017 Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications
BS EN 50341-1:2012 Overhead electrical lines exceeding AC 1 kV General requirements. Common specifications
I.S. EN 50341-1:2012 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
EN 50341-1:2012 Overhead electrical lines exceeding AC 1 kV - Part 1: General requirements - Common specifications
CEI EN 50341-1 : 2013 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
12/30260570 DC : 0 BS EN 50341-1 - OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS
PREN 50341-1 : DRAFT 2012 OVERHEAD ELECTRICAL LINES EXCEEDING AC 1 KV - PART 1: GENERAL REQUIREMENTS - COMMON SPECIFICATIONS

ISO 812:2017 Rubber, vulcanized or thermoplastic — Determination of low-temperature brittleness
ISO 9004-1:1994 Quality management and quality system elements Part 1: Guidelines
ISO 2921:2011 Rubber, vulcanized Determination of low-temperature retraction (TR test)
ISO 3951:1989 Sampling procedures and charts for inspection by variables for percent nonconforming
ISO 4662:2017 Rubber, vulcanized or thermoplastic Determination of rebound resilience
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO 1461:2009 Hot dip galvanized coatings on fabricated iron and steel articles — Specifications and test methods
IEC 60888:1987 Zinc-coated steel wires for stranded conductors
ISO 34-1:2015 Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces
ISO 2859-2:1985 Sampling procedures for inspection by attributes — Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
ISO 9002:1994 Quality systems — Model for quality assurance in production, installation and servicing
ISO 1183:1987 Plastics Methods for determining the density and relative density of non-cellular plastics
ISO 1431-1:2012 Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing
IEC 60050-466:1990 International Electrotechnical Vocabulary (IEV) - Part 466: Overhead lines
ISO 9001:2015 Quality management systems — Requirements
ISO 9003:1994 Quality systems Model for quality assurance in final inspection and test
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 3417:2008 Rubber Measurement of vulcanization characteristics with the oscillating disc curemeter
ISO 34-2:2015 Rubber, vulcanized or thermoplastic Determination of tear strength Part 2: Small (Delft) test pieces
ISO 9000-1:1994 Quality management and quality assurance standards — Part 1: Guidelines for selection and use
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
EN 61284:1997 Overhead lines - Requirements and tests for fittings
ISO 2781:2008 Rubber, vulcanized or thermoplastic Determination of density

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.