EN 791:1995+A1:2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
05-01-2014
02-11-2009
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions
4 List of hazards
5 Safety requirements and measures
5.1 General safety requirements
5.1.1 Intended use of the drill rig
5.1.2 Ergonomics
5.1.3 Hot and cold surfaces and sharp edges
5.1.4 Ventilating ports
5.1.5 Hoses, pipes and fittings under pressure
5.1.6 Materials
5.1.7 Handling of the drill rig and its parts
5.1.8 Access to operating positions and
servicing points
5.1.9 Isolation of energy sources
5.2 Driving, tramming and operating position
5.2.1 General
5.2.2 Operator's position
5.2.3 Underground drill rigs
5.2.4 Visibility
5.3 Controls, functions, systems
5.3.1 General
5.3.2 Starting
5.3.3 Stopping
5.3.4 Failure of the power supply
5.3.5 Failure in a control circuit
5.4 Control devices
5.4.1 General
5.4.2 Emergency stop and safety devices
5.4.3 Verification
5.5 Stability
5.5.1 General stability criteria
5.5.2 Definitions for stability calculations
5.5.3 Verification of stability
5.5.4 Ground pressure, calculation for crawler
mounted drill rigs
5.6 Carrier brakes
5.6.1 General
5.6.2 General requirements for wheel mounted
drill rigs
5.6.3 Service braking system for wheel mounted
drill rigs
5.6.4 Secondary braking system for wheel mounted
drill rigs
5.6.5 Parking braking system for wheel and crawler
mounted drill rigs
5.6.6 The service, secondary and parking braking
systems on crawler mounted drill rigs
5.6.7 Braking systems for 'skid steer' wheel mounted
drill rigs
5.6.8 Verification
5.7 Protection against moving parts
5.7.1 General
5.7.2 Transmission parts
5.7.3 Moving parts involved in the working process
5.8 Electrical installations
5.8.1 Electric power installation
5.8.2 Battery installation
5.9 Hydraulic installations
5.10 Pneumatic installations
5.11 Lighting
5.11.1 Working light
5.11.2 Illumination when tramming
5.12 Fire protection
5.12.1 General
5.12.2 Fire extinguishers
5.12.3 Installation of fire extinguishers
5.13 Noise and vibration
5.13.1 General
5.13.2 Noise
5.13.3 Vibration
5.14 Dust and gases
5.14.1 Dust suppression
5.14.2 Engines and engine exhausts
5.15 Draw-works, winches and ropes
5.15.1 General
5.15.2 Safety requirements
5.15.3 Winches for operating a drill rig
on slopes
5.16 Roller and leaf chains
5.17 Masts, derricks, feed beams and working platforms
5.17.1 General
5.17.2 Racking and working platforms
5.17.3 Personnel lift for operational work
5.17.4 Movable platforms for service, maintenance
and repair
5.17.5 Access
5.17.6 Escape systems
5.18 Special requirements for remotely controlled
and automated drill rigs
5.18.1 Operating position
5.18.2 Emergency stop
5.18.3 Control system
5.18.4 Fire protection
5.19 Warning devices
6 Verification of safety requirements/measures
7 Instructions for use - Instruction handbooks
7.1 Marking - Data plate
7.2 Indicators
7.2.1 Information indicators
7.2.2 Warning signs for residual hazards
7.3 Maintenance
7.4 Instruction handbooks for drill rigs
7.4.1 General
7.4.2 Operator's instructions
7.4.3 Special safety instructions in the
operator's instructions
7.4.4 Maintenance instructions
7.4.5 Special safety instructions in the
maintenance instruction
7.4.6 Spare parts list
Annex A (normative) - Measurement of noise and vibration
Annex B (normative) - Instructions for the examination and
checking of blocks, wire ropes and chains
Annex C (normative) - Brake test for drill rigs excluding
truck and tractor mounted drill rigs
Annex D (normative) - Hazards related to operation modes
of drill rigs
Annex E (informative) - Symbols and signs
Annex F - Bibliography
Annex ZA (informative) - Relationship between this European
Standard and the Essential
Requirements of EU Directive
98/37/EC, amended by 98/79/EC
Annex ZB (informative) - Relationship between this European
Standard and the Essential
Requirements of EU Directive
2006/42/EC
1.1The general term "Drill Rig" covers several differing types of machines for use in the construction industry, water well drilling industry, mining and quarrying, for use above ground as well as underground and for tunnel construction. The differing tasks determine the choice of drilling method and type of machine. For this reason there are many possible ways to separate drill rigs into different groups, e.g. in accordance with:-The task; -The drilling method used;-The cutting removal method;-The type of construction work.The methods used for drilling can be basically differentiated in percussive and rotary drilling principles.Percussive drilling is a method by which the hole is produced by crushing the ground or rock at the bottom of the drill-hole by striking it with the drilling tool and removing the cuttings out of the bore-hole.Rotary drilling is a method in which the drilling tool at the bottom of the borehole is rotated and at the same time, a feed force is applied by a feed system or drill collar. The ground or rock at the bottom of the borehole is crushed or cut by pressure, shear or tensile stress produced by the different drilling tools. The cuttings are periodically or continuously removed out of the bore hole.Rotary percussive drilling is performed by a piston striking directly on the bit (down the hole hammer drills) or by percussive energy transmitted via a drill string to the bit. The piston is powered by either hydraulic fluid or compressed air.At the same time the drill bit is rotated either continuously or intermittently.The cuttings are continuously removed out of the borehole by a flushing medium, air or fluid which is carried to the drilling tool.Typical examples of drill rigs covered by this standard are:-Cable tool drill rig;-Pile drill rigs;-Pile top drill rig;-Raise borer;-Reverse circulation drill rig;-Rotary and percussive drill rig for underground drilling;-Rotary and percussive drill rig
| Committee |
CEN/TC 151
|
| DevelopmentNote |
1995 Edition Re-Issued in February 2009 & incorporates AMD 1 2009. (03/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| NS EN 791 : 1995 + A1 2009 | Identical |
| NBN EN 791 : 1996 + A1 2009 | Identical |
| BS EN 791 : 1996 | Identical |
| NF EN 791 : 1996 + A1 2009 | Identical |
| PN EN 791 : 1998 + A1 2009 | Identical |
| UNI EN 791 : 2009 | Identical |
| SN EN 791 : 1996 + A1 2009 | Identical |
| NEN EN 791 : 1995 + A1 2009 | Identical |
| UNE-EN 791:1996 | Identical |
| DIN EN 791:2010-01 | Identical |
| I.S. EN 791:1996 | Identical |
| BS EN 791:1995+A1:2009 | Identical |
| UNE-EN 791:1996+A1:2009 | Identical |
| 08/30192726 DC : 0 | BS EN 1538 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS |
| 07/30172830 DC : DRAFT DEC 2007 | BS EN 15746-1 - RAILWAY APPLICATIONS - TRACK - ROAD-RAIL MACHINES AND ASSOCIATED - EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| BS ISO 18400-102:2017 | Soil quality. Sampling Selection and application of sampling techniques |
| BS ISO 20474-1:2017 | Earth-moving machinery. Safety General requirements |
| PREN 14199 : DRAFT 2013 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES |
| 12/30244746 DC : 0 | BS EN 15955-1 - RAILWAY APPLICATIONS - TRACK - DEMOUNTABLE MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| PD ISO/TR 12603:2010 | Building construction machinery and equipment. Classification |
| PREN 1536 : DRAFT 2008 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES |
| 13/30280743 DC : 0 | BS EN 14199 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - MICROPILES |
| DIN EN 15954-1:2014-06 | RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| 16/30277591 DC : 0 | BS ISO 20474-12 - EARTH-MOVING MACHINERY - SAFETY - PART 12: REQUIREMENTS FOR CABLE EXCAVATORS |
| BS EN ISO 22476-5:2012 | Geotechnical investigation and testing. Field testing Flexible dilatometer test |
| 09/30202535 DC : DRAFT JUN 2009 | BS EN 15955-1 - RAILWAY APPLICATIONS - TRACK - DEMOUNTABLE MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| 10/30185766 DC : 0 | BS EN 1889-1 - MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| BS EN 15746-1 : 2010 | RAILWAY APPLICATIONS - TRACK - ROAD-RAIL MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| I.S. EN ISO 22282-1:2012 | GEOTECHNICAL INVESTIGATION AND TESTING - GEOHYDRAULIC TESTING - PART 1: GENERAL RULES (ISO 22282-1:2012) |
| ISO 18400-102:2017 | Soil quality — Sampling — Part 102: Selection and application of sampling techniques |
| 15/30279805 DC : 0 | BS EN 15746-1 - RAILWAY APPLICATIONS - TRACK - ROAD RAIL MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR TRAVELLING AND WORKING |
| DIN EN ISO 22475-1:2007-01 | Geotechnical investigation and testing - Sampling methods and groundwater measurements - Part 1: Technical principles for execution (ISO 22475-1:2006); German version EN ISO 22475-1:2006 |
| BS EN 14731:2005 | Execution of special geotechnical works. Ground treatment by deep vibration |
| UNE-EN 15954-1:2014 | Railway applications - Track - Trailers and associated equipment - Part 1: Technical requirements for running and working |
| I.S. EN ISO 22475-1:2006 | GEOTECHNICAL INVESTIGATION AND TESTING - SAMPLING METHODS AND GROUNDWATER MEASUREMENTS - PART 1: TECHNICAL PRINCIPLES FOR EXECUTION |
| BS DD237(1996) : 1996 | BUILDING CONSTRUCTION MACHINERY AND EQUIPMENT - CLASSIFICATION |
| 17/30341100 DC : 0 | BS ISO 18758-2 - MINING AND EARTH-MOVING MACHINERY - ROCK DRILL RIGS AND ROCK REINFORCEMENT RIGS - PART 2: SAFETY REQUIREMENTS |
| 10/30233949 DC : 0 | BS EN 12111 - TUNNELLING MACHINES - ROAD HEADERS, CONTINUOUS MINERS AND IMPACT RIPPERS - SAFETY REQUIREMENTS |
| 14/30258500 DC : 0 | BS EN 14033-2 - RAILWAY APPLICATIONS - TRACK - RAILBOUND CONSTRUCTION AND MAINTENANCE MACHINES - PART 2: TECHNICAL REQUIREMENTS FOR TRAVELLING AND WORKING |
| UNE-EN ISO 22476-5:2014 | Geotechnical investigation and testing - Field testing - Part 5: Flexible dilatometer test (ISO 22476-5:2012) |
| PREN 1889-1 : DRAFT 2010 | MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| 08/30177213 DC : DRAFT JUNE 2008 | BS EN 13524 AMD1 - HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS |
| 14/30272921 DC : 0 | BS ISO 18400-102 - SOIL QUALITY - SAMPLING - PART 102: SELECTION AND APPLICATION OF SAMPLING TECHNIQUES |
| BS EN ISO 22282-1:2012 | Geotechnical investigation and testing. Geohydraulic testing General rules |
| 08/30123706 DC : DRAFT APR 2008 | ISO 22282-1 - GEOTECHNICAL INVESTIGATION AND TESTING - GEOHYDRAULIC TESTING - PART 1: GENERAL RULES |
| 09/30202529 DC : 0 | BS EN 15954-1 - RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| I.S. EN ISO 22476-5:2012 | GEOTECHNICAL INVESTIGATION AND TESTING - FIELD TESTING - PART 5: FLEXIBLE DILATOMETER TEST (ISO 22476-5:2012) |
| ISO 20474-12:2017 | Earth-moving machinery — Safety — Part 12: Requirements for cable excavators |
| DIN EN 1538:2015-10 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS |
| DIN EN 15237 E : 2007 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - VERTICAL DRAINAGE |
| DIN EN 14679:2005-07 | Execution of special geotechnical works - Deep mixing |
| BS EN 13524 : 2003 | HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS |
| BS EN 1538 : 2010 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DIAPHRAGM WALLS |
| I.S. EN 13524:2003 | HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS |
| DIN EN 13524:2003-10 | HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS |
| EN 13524:2003+A2:2014 | Highway maintenance machines - Safety requirements |
| DIN EN 1536:2015-10 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES |
| EN 15746-1:2010+A1:2011 | Railway applications - Track - Road-rail machines and associated equipment - Part 1: Technical requirements for running and working |
| I.S. EN 12348:2000 | CORE DRILLING MACHINES ON STAND - SAFETY |
| I.S. EN 474-12:2006 | EARTH-MOVING MACHINERY - SAFETY - PART 12: REQUIREMENTS FOR CABLE EXCAVATORS |
| I.S. EN 1889-1:2011 | MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| UNI EN 15746-1 : 2011 | RAILWAY APPLICATIONS - TRACK - ROAD-RAIL MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| I.S. EN 1536:2010 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES |
| I.S. EN 1538:2010 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS |
| BS ISO 20474-12:2017 | Earth-moving machinery. Safety Requirements for cable excavators |
| 08/30192723 DC : 0 | BS EN 1536 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES |
| 07/30163503 DC : 0 | BS ISO 20474-12 - EARTH-MOVING MACHINERY - SAFETY - PART 12: REQUIREMENTS FOR ROPE EXCAVATORS |
| NF EN 15746-1 : 2010 + A1 2011 | RAILWAY APPLICATIONS - TRACK - ROAD-RAIL MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| 12/30244740 DC : 0 | BS EN 15954-1 - RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| 04/30113757 DC : DRAFT MAY 2004 | EN ISO 22475-1 - GEOTECHNICAL INVESTIGATION AND TESTING - SAMPLING BY DRILLING AND EXCAVATION METHODS AND GROUNDWATER MEASUREMENTS - PART 1: TECHNICAL PRINCIPLES FOR EXECUTION |
| UNE-EN ISO 22282-1:2013 | Geotechnical investigation and testing - Geohydraulic testing - Part 1: General rules (ISO 22282-1:2012) |
| 14/30292494 DC : 0 | BS EN ISO 22476-15 - GEOTECHNICAL INVESTIGATION AND TESTING - FIELD TESTING - PART 15: MEASURING WHILE DRILLING |
| ISO 18758-2:2018 | Mining and earth-moving machinery — Rock drill rigs and rock reinforcement rigs — Part 2: Safety requirements |
| I.S. EN 15955-1:2013 | RAILWAY APPLICATIONS - TRACK - DEMOUNTABLE MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| PREN 12699 : DRAFT 2013 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES |
| ISO/TR 12603:2010 | Building construction machinery and equipment Classification |
| UNI EN ISO 22476-5 : 2013 | GEOTECHNICAL INVESTIGATION AND TESTING - FIELD TESTING - PART 5: FLEXIBLE DILATOMETER TEST |
| DIN EN 12348:2010-01 | Core drilling machines on stand - Safety (includes Amendment A1:2009) |
| DIN EN 14731 E : 2005 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - GROUND TREATMENT BY DEEP VIBRATION |
| BS EN 15237:2007 | Execution of special geotechnical works. Vertical drainage |
| UNE-EN 1889-1:2012 | Machines for underground mines - Mobile machines working underground - Safety - Part 1: Rubber tyred vehicles |
| DIN EN 1889-1:2011-10 | MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| UNI EN 15955-1 : 2013 | RAILWAY APPLICATIONS - TRACK - DEMOUNTABLE MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| UNI EN 1889-1 : 2011 | MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| UNI EN 474-12 : 2009 | EARTH-MOVING MACHINERY - SAFETY - PART 12: REQUIREMENTS FOR CABLE EXCAVATORS |
| UNI EN 14679 : 2005 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING |
| UNI EN 996 : 2009 | PILING EQUIPMENT - SAFETY REQUIREMENTS |
| UNI EN 15954-1 : 2013 | RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| UNI EN 12348 : 2009 | CORE DRILLING MACHINES ON STAND - SAFETY |
| DIN EN 15746-1:2016-02 (Draft) | Railway applications - Track - Road rail machines and associated equipment - Part 1: Technical requirements for travelling and working; German and English version prEN 15746-1:2015 |
| 16/30277014 DC : DRAFT MAR 2016 | BS ISO 20474-1 - EARTH-MOVING MACHINERY - SAFETY - PART 1: GENERAL REQUIREMENTS |
| UNI EN ISO 22282-1 : 2012 | GEOTECHNICAL INVESTIGATION AND TESTING - GEOHYDRAULIC TESTING - PART 1: GENERAL RULES |
| I.S. EN 15746-1:2010 | RAILWAY APPLICATIONS - TRACK - ROAD-RAIL MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| UNE-EN 15237:2011 | Execution of special geotechnical works - Vertical drainage |
| DIN EN 14679 E : 2005 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING |
| DIN EN 474-12:2010-05 | Earth-moving machinery - Safety - Part 12: Requirements for cable excavators (includes Amendment A1:2008) |
| ISO 22282-1:2012 | Geotechnical investigation and testing — Geohydraulic testing — Part 1: General rules |
| UNE-EN 1538:2011 | Execution of special geotechnical work - Diaphragm walls |
| UNE-EN 13524:2003 | Highway maintenance machines - Safety requirements |
| BS EN 996 : 1996 | PILING EQUIPMENT - SAFETY REQUIREMENTS |
| BS EN 12348 : 2000 | CORE DRILLING MACHINES ON A STAND - SAFETY |
| BS EN 14679:2005 | Execution of special geotechnical works. Deep mixing |
| BS EN 1536 : 2010 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - BORED PILES |
| BS EN 474-12 : 2006 | EARTH-MOVING MACHINERY - SAFETY - PART 12: REQUIREMENTS FOR CABLE EXCAVATORS |
| ISO 22476-5:2012 | Geotechnical investigation and testing — Field testing — Part 5: Flexible dilatometer test |
| DIN EN 15237:2007-06 | Execution of special geotechnical works - Vertical drainage |
| UNE-EN 15955-1:2014 | Railway applications - Track - Demountable machines and associated equipment - Part 1: Technical requirements for running and working |
| UNE-EN ISO 22475-1:2010 | Geotechnical investigation and testing - Sampling methods and groundwater measurements - Part 1: Technical principles for execution (ISO 22475-1:2006) |
| ISO 22475-1:2006 | Geotechnical investigation and testing Sampling methods and groundwater measurements Part 1: Technical principles for execution |
| EN 14679:2005/AC:2006 | EXECUTION OF SPECIAL GEOTECHNICAL WORKS - DEEP MIXING |
| EN 1538:2010+A1:2015 | Execution of special geotechnical work - Diaphragm walls |
| EN 1536:2010+A1:2015 | Execution of special geotechnical work - Bored piles |
| EN 14731:2005 | Execution of special geotechnical works - Ground treatment by deep vibration |
| EN 15954-1 : 2013 | RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| EN ISO 22282-1:2012 | Geotechnical investigation and testing - Geohydraulic testing - Part 1: General rules (ISO 22282-1:2012) |
| UNI EN 13524 : 2014 | HIGHWAY MAINTENANCE MACHINES - SAFETY REQUIREMENTS |
| EN 996:1995+A3:2009 | Piling equipment - Safety requirements |
| EN ISO 22476-5:2012 | Geotechnical investigation and testing - Field testing - Part 5: Flexible dilatometer test (ISO 22476-5:2012) |
| EN 15237:2007 | Execution of special geotechnical works - Vertical drainage |
| EN 1889-1:2011 | Machines for underground mines - Mobile machines working underground - Safety - Part 1: Rubber tyred vehicles |
| EN 15955-1 : 2013 | RAILWAY APPLICATIONS - TRACK - DEMOUNTABLE MACHINES AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| EN 474-12:2006+A1:2008 | Earth-moving machinery - Safety - Part 12: Requirements for cable excavators |
| 03/308533 DC : DRAFT JUNE 2003 | EN 14731 - EXECUTION OF SPECIAL GEOTECHNICAL WORKS - GROUP TREATMENT BY DEEP VIBRATION |
| DIN EN 15955-1:2013-08 | Railway applications - Track - Demountable machines and associated equipment - Part 1: Technical requirements for running and working |
| BS EN 15954-1:2013 | Railway applications. Track. Trailers and associated equipment Technical requirements for running and working |
| DIN EN ISO 22476-5:2013-03 | Geotechnical investigation and testing - Field testing - Part 5: Flexible dilatometer test (ISO 22476-5:2012) |
| PREN 1538 : DRAFT 2008 | EXECUTION OF SPECIAL GEOTECHNICAL WORK - DIAPHRAGM WALLS |
| BS EN 15955-1:2013 | Railway applications. Track. Demountable machines and associated equipment Technical requirements for running and working |
| 13/30280740 DC : 0 | BS EN 12699 - EXECUTION OF SPECIAL GEOTECHNICAL WORK - DISPLACEMENT PILES |
| 05/19988433 DC : 0 | PREN 14033-2 - RAILWAY APPLICATIONS - TRACK - RAILBOUND CONSTRUCTION AND MAINTENANCE MACHINES - PART 2: TECHNICAL REQUIREMENTS FOR WORKING |
| DIN EN ISO 22282-1:2012-09 | Geotechnical investigation and testing - Geohydraulic testing - Part 1: General rules (ISO 22282-1:2012) |
| I.S. EN 15954-1:2013 | RAILWAY APPLICATIONS - TRACK - TRAILERS AND ASSOCIATED EQUIPMENT - PART 1: TECHNICAL REQUIREMENTS FOR RUNNING AND WORKING |
| DIN EN 13524:2014-07 | Highway maintenance machines - Safety requirements (includes Amendment A2:2014) |
| DIN EN 1889-1 E : 2011 | MACHINES FOR UNDERGROUND MINES - MOBILE MACHINES WORKING UNDERGROUND - SAFETY - PART 1: RUBBER TYRED VEHICLES |
| BS EN 1889-1:2011 | Machines for underground mines. Mobile machines working underground. Safety Rubber tyred vehicles |
| BS EN ISO 22475-1:2006 | Geotechnical investigation and testing. Sampling methods and groundwater measurements Technical principles for execution |
| UNE-EN 1536:2011 | Execution of special geotechnical work - Bored piles |
| DIN EN 15746-1:2011-12 | Railway applications - Track - Road-rail machines and associated equipment - Part 1: Technical requirements for running and working (includes Amendment A1:2011) |
| EN ISO 22475-1:2006 | Geotechnical investigation and testing - Sampling methods and groundwater measurements - Part 1: Technical principles for execution (ISO 22475-1:2006) |
| DIN EN 14731:2005-12 | Execution of special geotechnical works - Ground treatment by deep vibration |
| EN 12348:2000+A1:2009 | Core drilling machines on stand - Safety |
| DIN EN 996:2010-02 | PILING EQUIPMENT - SAFETY REQUIREMENTS |
| UNE-EN 15746-1:2011 | Railway applications - Track - Road-rail machines and associated equipment - Part 1: Technical requirements for running and working |
| ISO 3449:2005 | Earth-moving machinery — Falling-object protective structures — Laboratory tests and performance requirements |
| EN 294:1992/AC:1993 | SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT DANGER ZONES BEING REACHED BY THE UPPER LIMBS |
| EN 418 : 1992 | SAFETY OF MACHINERY - EMERGENCY STOP EQUIPMENT, FUNCTIONAL ASPECTS - PRINCIPLES FOR DESIGN |
| ISO 4302:2016 | Cranes Wind load assessment |
| ISO 10570:2004 | Earth-moving machinery — Articulated frame lock — Performance requirements |
| ISO 4872:1978 | Acoustics Measurement of airborne noise emitted by construction equipment intended for outdoor use Method for determining compliance with noise limits |
| ISO 7095:1982 | Earth-moving machinery Crawler tractors and crawler loaders Operator's controls |
| ISO 4253:1993 | Agricultural tractors — Operator's seating accommodation — Dimensions |
| ISO 6405-2:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 2: Symbols for specific machines, equipment and accessories |
| EN 22860 : 1985 | EARTH-MOVING MACHINERY - MINIMUM ACCESS DIMENSIONS INCORPORATING AN AGREED COMMON MODIFICATION |
| EN 23164 : 1985 | EARTH-MOVING MACHINERY - LABORATORY EVALUATIONS OF ROLL-OVER & FALLING-OBJECT PROTECTIVE STRUCTURES - SPECIFICATION FOR THE DEFLECTION-LIMITING VOLUME |
| ISO 5010:2007 | Earth-moving machinery Rubber-tyred machines Steering requirements |
| EN 292-1 : 1991 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - BASIC TERMINOLOGY, METHODOLOGY |
| ISO 3795:1989 | Road vehicles, and tractors and machinery for agriculture and forestry — Determination of burning behaviour of interior materials |
| EN 50081-2:1993 | Electromagnetic compatibility - Generic emission standard - Part 2: Industrial environment |
| ISO 4309:2010 | Cranes Wire ropes Care and maintenance, inspection and discard |
| ISO 3471-1:1986 | Earth-moving machinery — Roll-over protective structures — Laboratory tests and performance requirements — Part 1: Crawler, wheel loaders and tractors, backhoe loaders, graders, tractor scrapers, articulated steer dumpers |
| ISO 6405-1:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 1: Common symbols |
| ISO 3457:2003 | Earth-moving machinery Guards Definitions and requirements |
| EN 23411 : 1988 | EARTH-MOVING MACHINERY - HUMAN PHYSICAL DIMENSIONS OF OPERATORS & MINIMUM OPERATOR SPACE ENVELOPE |
| ISO 2631-1:1997 | Mechanical vibration and shock — Evaluation of human exposure to whole-body vibration — Part 1: General requirements |
| ENV 1070 : 1993 | SAFETY OF MACHINERY - TERMINOLOGY |
| EN 50082-2 : 95 AC 95 | ELECTROMAGNETIC COMPATIBILITY - GENERIC IMMUNITY STANDARD - INDUSTRIAL ENVIRONMENT |
| EN 292-2 : 91 AMD 1 95 | SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - TECHNICAL PRINCIPLES AND SPECIFICATION |
| ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
| 1998/37/EC : 1998 | DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY |
| ISO 3864:1984 | Safety colours and safety signs |
| ISO 2867:2011 | Earth-moving machinery Access systems |
| EN 61310-1:2008 | Safety of machinery - Indication, marking and actuation - Part 1: Requirements for visual, acoustic and tactile signals |
| ISO 3450:2011 | Earth-moving machinery — Wheeled or high-speed rubber-tracked machines — Performance requirements and test procedures for brake systems |
| IEC 60651:1979+AMD1:1993+AMD2:2000 CSV | Sound level meters |
| IEC 60804:2000 | Integrating-averaging sound level meters |
| ISO 6750:2005 | Earth-moving machinery Operator's manual Content and format |
| EN 60204-1 : 2006 COR 2010 | SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.