• There are no items in your cart

EN ISO 20753:2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS - TEST SPECIMENS (ISO 20753:2008)
Superseded date

05-31-2019

Published date

05-27-2014

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Preparation of test specimens
5 Types of test specimen and their dimensions
6 Report on preparation of test specimens
Annex A (informative) - Recommended applications for
        multipurpose test specimens or parts thereof
Annex B (normative) - Designation system for test specimens
Bibliography

Describes dimensional requirements relating to test specimens prepared from plastics materials intended for processing by moulding as well as to test specimens prepared by machining from sheets or shaped articles.

Committee
TC 249
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

IEC 60112:2003+AMD1:2009 CSV Method for the determination of the proof and the comparative tracking indices of solid insulating materials
ISO 4589-3:2017 Plastics — Determination of burning behaviour by oxygen index — Part 3: Elevated-temperature test
ISO 10350-2:2011 Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics
ISO 22088-1:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 1: General guidance
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 3167:2014 Plastics Multipurpose test specimens
ISO 294-5:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 5: Preparation of standard specimens for investigating anisotropy
ISO 11403-3:2014 Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties
ISO 294-3:2002 Plastics Injection moulding of test specimens of thermoplastic materials Part 3: Small plates
ISO 22088-2:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 2: Constant tensile load method
ISO 295:2004 Plastics — Compression moulding of test specimens of thermosetting materials
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 22088-5:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 5: Constant tensile deformation method
ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 8256:2004 Plastics — Determination of tensile-impact strength
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 2039-2:1987 Plastics Determination of hardness Part 2: Rockwell hardness
ISO 11403-2:2012 Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
ISO 180:2000 Plastics Determination of Izod impact strength
ISO 22088-3:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 3: Bent strip method
ISO 294-2:1996 Plastics Injection moulding of test specimens of thermoplastic materials Part 2: Small tensile bars
ISO 899-2:2003 Plastics Determination of creep behaviour Part 2: Flexural creep by three-point loading
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 604:2002 Plastics — Determination of compressive properties
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
IEC 60426:2007 Electrical insulating materials - Determination of electrolytic corrosion caused by insulating materials - Test methods
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 22088-4:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 4: Ball or pin impression method
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 22088-6:2006 Plastics Determination of resistance to environmental stress cracking (ESC) Part 6: Slow strain rate method
ISO 4589-2:2017 Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-temperature test
ISO 2818:1994 Plastics — Preparation of test specimens by machining
ISO 899-1:2017 Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 11403-1:2014 Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties
ASTM D 1822 : 2013 : REDLINE Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials
ISO 178:2010 Plastics Determination of flexural properties
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.