EN ISO 295 : 2004
Current
Current
The latest, up-to-date edition.
PLASTICS - COMPRESSION MOULDING OF TEST SPECIMENS OF THERMOSETTING MATERIALS
Published date
02-01-2004
Publisher
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Apparatus
5 Conditioning of material prior to moulding
6 Preparation of the charge
7 Moulding conditions
7.1 General
7.2 Drying
7.3 High-frequency preheating
7.4 Pre-plastification
7.5 Release agents
7.6 Breathing
8 Procedure
9 Precision
10 Moulding report
Annex A (informative) Marking of test specimens
Bibliography
Provides the general principles and lays down the procedure to prepare test specimens of heat- and pressure-moulded thermosetting material from different moulding compounds; specifies the details for test specimen preparation to be included with the test reports on properties; gives the general principles for the design of the mould intended for the preparation of the test specimens.
| Committee |
CEN/TC 249
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| UNE-EN ISO 295:2004 | Identical |
| DIN EN ISO 295:2004-05 | Identical |
| I.S. EN ISO 295:2004 | Identical |
| UNI EN ISO 295 : 2005 | Identical |
| PN EN ISO 295 : 2006 | Identical |
| DIN EN ISO 295 E : 2004 | Identical |
| BS EN ISO 295:2004 | Identical |
| NF EN ISO 295 : 2004 | Identical |
| NS EN ISO 295 : 2ED 2004 | Identical |
| ISO 295:2004 | Identical |
| SN EN ISO 295 : 2004 | Identical |
| NEN EN ISO 295 : 2004 | Identical |
| NBN EN ISO 295 : 2004 | Identical |
| I.S. EN 60695-11-20:2015 | FIRE HAZARD TESTING - PART 11-20: TEST FLAMES - 500 W FLAME TEST METHODS |
| I.S. EN ISO 180:2001 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000) |
| DIN EN 14598-3:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| DIN EN 14598-2:2005-07 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements |
| EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013) |
| EN 60695-2-12:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS (IEC 60695-2-12:2010/A1:2014) |
| BS EN 60695-11-10:2013 | Fire hazard testing Test flames. 50 W horizontal and vertical flame test methods |
| BS EN 60695-2-12 : 2010 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| CEI EN 60695-10-2 : 2015 | FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD |
| BS EN ISO 180 : 2001 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH |
| DIN EN ISO 6603-1:2000-10 | PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 1: NON-INSTRUMENTED IMPACT TESTING |
| BS EN 14598-2:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements |
| BS EN ISO 604:2003 | Plastics. Determination of compressive properties |
| I.S. EN ISO 604:2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| UNE-EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| I.S. EN 60243-1:2013 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES (IEC 60243-1:2013 (EQV)) |
| ISO 604:2002 | Plastics — Determination of compressive properties |
| I.S. EN 60695-10-2:2014 | FIRE HAZARD TESTING - PART 10-2: ABNORMAL HEAT - BALL PRESSURE TEST METHOD |
| I.S. EN 60695-11-10:2013 | FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS (IEC 60695-11-10:2013 (EQV)) |
| EN 60695-2-13:2010/A1:2014 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS (IEC 60695-2-13:2010/A1:2014) |
| BS EN ISO 6603-1:2000 | Plastics. Determination of multi-axial impact behaviour of rigid plastics Non-instrumented impact testing |
| UNI EN ISO 180 : 2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH |
| EN 60695-10-2:2014 | Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test method |
| UNI EN ISO 604 : 2008 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| I.S. EN 60695-2-13:2010 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| BS EN 60243-1:2013 | Electric strength of insulating materials. Test methods Tests at power frequencies |
| BS EN 60695-11-20:2015 | Fire hazard testing Test flames. 500 W flame test methods |
| CEI EN 60243-1 : 2014 | ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES |
| EN ISO 180:2000/A2:2013 | PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH (ISO 180:2000/AMD 2:2013) |
| DIN EN ISO 604 E : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| 02/124520 DC : DRAFT DEC 2002 | EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS |
| DIN EN ISO 604:2003-12 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES |
| BS EN 14598-3:2005 | Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements |
| ISO 180:2000 | Plastics Determination of Izod impact strength |
| UNE-EN 60695-11-20:2016 | Fire hazard testing - Part 11-20: Test flames - 500 W flame test methods |
| UNE-EN 60695-11-10:2014 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| EN ISO 15252-2 : 1999 | PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN 14598-2:2005/AC:2006 | REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS |
| EN ISO 14529-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 11248 : 1999 | Plastics - Thermosetting moulding materials - Evaluation of short-term performance at elevated temperatures (ISO 11248:1993) |
| EN ISO 14530-2 : 1999 | PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 604 : 2003 | PLASTICS - DETERMINATION OF COMPRESSIVE PROPERTIES (ISO 604:2002) |
| EN ISO 14528-2 : 1999 | PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| EN ISO 6603-1 : 2000 | PLASTICS - DETERMINATION OF PUNCTURE IMPACT BEHAVIOUR OF RIGID PLASTICS - PART 1: NON-INSTRUMENTED IMPACT TESTING |
| EN 14598-3:2005 | Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements |
| EN ISO 14527-2 : 1999 | PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
| BS EN 60695-2-13 : 2010 | FIRE HAZARD TESTING - PART 2-13: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE IGNITION TEMPERATURE (GWIT) TEST METHOD FOR MATERIALS |
| UNE-EN 60695-2-13:2011 | Fire hazard testing -- Part 2-13: Glowing/hot-wire based test methods - Glow-wire ignition temperature (GWIT) test method for materials |
| I.S. EN 60695-2-12:2010 | FIRE HAZARD TESTING - PART 2-12: GLOWING/HOT-WIRE BASED TEST METHODS - GLOW-WIRE FLAMMABILITY INDEX (GWFI) TEST METHOD FOR MATERIALS |
| BS EN 60695-10-2:2014 | Fire hazard testing Abnormal heat. Ball pressure test method |
| UNE-EN 60695-2-12:2011 | Fire hazard testing -- Part 2-12: Glowing/hot-wire based test methods - Glow-wire flammability index (GWFI) test method for materials |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 14526-1:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 3167:2014 | Plastics Multipurpose test specimens |
| ISO 11403-3:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 3: Environmental influences on properties |
| ISO 10350-1:2017 | Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials |
| ISO 10724-1:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens |
| ISO 14528-2:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14529-3:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14529-1:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 11403-2:2012 | Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties |
| ISO 14530-1:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 14530-3:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 1183:1987 | Plastics Methods for determining the density and relative density of non-cellular plastics |
| ISO 14526-2:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 472:2013 | Plastics Vocabulary |
| ISO 14526-3:1999 | Plastics Phenolic powder moulding compounds (PF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14528-1:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 2577:2007 | Plastics Thermosetting moulding materials Determination of shrinkage |
| ISO 14527-3:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 2818:1994 | Plastics — Preparation of test specimens by machining |
| ISO 14527-1:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 1: Designation system and basis for specifications |
| ISO 14529-2:1999 | Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 11403-1:2014 | Plastics Acquisition and presentation of comparable multipoint data Part 1: Mechanical properties |
| ISO 15252-1:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 1: Designation system and basis for specifications |
| ISO 15252-3:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 15252-2:1999 | Plastics Epoxy powder moulding compounds (EP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14530-2:1999 | Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 14528-3:1999 | Plastics Melamine-formaldehyde powder moulding compounds (MF-PMCs) Part 3: Requirements for selected moulding compounds |
| ISO 14527-2:1999 | Plastics Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) Part 2: Preparation of test specimens and determination of properties |
| ISO 10724-2:1998 | Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 2: Small plates |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.