EN ISO 4759-3:2016
Current
Current
The latest, up-to-date edition.
Tolerances for fasteners - Part 3: Washers for bolts, screws and nuts - Product grades A, C and F (ISO 4759-3:2016)
Published date
06-29-2016
Publisher
ISO 4759-3:2016 specifies tolerances for flat washers of product grades A, C and F with nominal diameters of 1 mm to 150 mm inclusive, designed to be used in bolted joints in combination with bolts, screws, studs and nuts.This part of ISO 4759 may be applied to non-flat washers however it does not include all the tolerances related to these washers.It applies to non-captive and captive washers, and to standard and non-standard washers.It does not apply to dynamic disc springs.Washers of product grades F and A are intended to be used with bolts, screws, studs and nuts of product grades A and B; washers of product grade C are intended to be used with bolts, screws, studs and nuts of product grade C.NOTE The product grade refers to a specific tolerance range related to dimensional and geometrical characteristics (product grade F for fine tolerances, product grade A for precise tolerances, product grade C for large tolerances).Annex A presents tolerances taken from ISO 286‑1 and ISO 286‑2.
| Committee |
CEN/TC 185
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Standards | Relationship |
| NF EN ISO 4759-3 : 2016 | Identical |
| SS-EN ISO 4759-3:2016 | Identical |
| UNI EN ISO 4759-3 : 2002 | Identical |
| BS EN ISO 4759-3:2000 | Identical |
| NEN EN ISO 4759-3 : 2016 | Identical |
| NS EN ISO 4759-3 : 2000 | Identical |
| NBN EN ISO 4759-3 : 1ED 2000 | Identical |
| DIN EN ISO 4759-3:2016-12 | Identical |
| ISO 4759-3:2016 | Identical |
| UNE-EN ISO 4759-3:2000 | Identical |
| UNI EN ISO 4759-3 :2016 | Identical |
| DIN EN ISO 4759-3 E : 2000 | Identical |
| DIN EN ISO 4759-3:2015-01 (Draft) | Identical |
| PN EN ISO 4759-3 : 2016 | Identical |
| UNE-EN ISO 4759-3:2017 | Identical |
| SN EN ISO 4759-3:2016 | Identical |
| I.S. EN ISO 4759-3:2016 | Identical |
| 03/318786 DC : DRAFT NOV 2003 | EN 14831 - FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| 13/30277440 DC : 0 | BS EN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| BS EN ISO 7089:2000 | Plain washers. Normal series. Product grade A |
| 07/30107797 DC : 0 | BS EN 14399-9 - HIGH STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - BOLT AND NUT ASSEMBLIES WITH DIRECT TENSION INDICATORS |
| PREN 14399-5 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| 02/704464 DC : DRAFT MAR 2002 | PREN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 5: PLAIN WASHERS FOR SYSTEM HR |
| UNI EN 14399-9 : 2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| UNE-EN 14399-1:2016 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| UNE-EN 14399-6:2016 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| BS EN 14399-5 : 2015-02 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| BS EN 14399-1:2015 | High-strength structural bolting assemblies for preloading General requirements |
| I.S. EN 14399-6:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN 14399-5:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| I.S. EN 14399-1:2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| DIN 7989-1:2001-04 | Washers for steel structures - Part 1: Product grade C |
| 13/30277437 DC : 0 | BS EN 14399-5 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| PREN 14399-9 : DRAFT 2015 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| PREN 14399-6 : DRAFT 2013 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| I.S. EN ISO 7091:2000 | PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C |
| DIN EN ISO 7093-1:2000-11 | PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A |
| DIN EN 14831 E : 2005 | FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| EN ISO 3269:2000 | FASTENERS - ACCEPTANCE INSPECTION |
| UNI EN 14831 : 2005 | FASTENERS - TIGHTENING PERFORMANCE - TORQUE/ANGLE SIMPLIFIED TEST METHOD |
| I.S. EN ISO 7094:2000 | PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C |
| DIN 7989-2:2001-04 | Washers for steel structures - Part 2: Product grade A |
| DIN 440:2001-03 | WASHERS - WITH SQUARE HOLE, ESPECIALLY FOR TIMBER CONSTRUCTIONS |
| 02/704465 DC : DRAFT MAR 2002 | PREN 14399-6 - HIGH-STRENGTH STRUCTURAL BOLTING FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS FOR SYSTEMS HR AND HV |
| 04/30123693 DC : DRAFT OCT 2004 | EN 15048-1 - NON-PRELOADED STRUCTURAL BOLTING ASSEMBLIES - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 14399-5:2016 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| DIN EN 14399-9:2016-01 (Draft) | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| DIN EN ISO 7093-2:2000-11 | PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C |
| BS EN 14399-6:2005 | High-strength structural bolting assemblies for preloading Plain chamfered washers |
| BS EN ISO 3269:2001 | Fasteners. Acceptance inspection |
| BS EN 14831:2005 | Fasteners. Tightening performance. Torque/Angle simplified test method |
| EN ISO 7089 : 2000 | PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE A |
| EN 14399-1:2015 | High-strength structural bolting assemblies for preloading - Part 1: General requirements |
| EN ISO 7093-2 : 2000 | PLAIN WASHERS - LARGE SERIES - PART 2: PRODUCT GRADE C |
| EN ISO 7091 : 2000 | PLAIN WASHERS - NORMAL SERIES - PRODUCT GRADE C |
| EN 14399-9:2018 | High-strength structural bolting assemblies for preloading - Part 9: System HR or HV - Direct tension indicators for bolt and nut assemblies |
| EN ISO 7094:2000/AC:2002 | PLAIN WASHERS - EXTRA LARGE SERIES - PRODUCT GRADE C |
| EN ISO 7090 : 2000 | PLAIN WASHERS, CHAMFERED - NORMAL SERIES - PRODUCT GRADE A (ISO 7090:2000) |
| EN ISO 7092 : 2000 | PLAIN WASHERS - SMALL SERIES - PRODUCT GRADE A |
| EN ISO 7093-1 : 2000 | PLAIN WASHERS - LARGE SERIES - PART 1: PRODUCT GRADE A (ISO 7093-1:2000) |
| EN 14399-5:2015 | High-strength structural bolting assemblies for preloading - Part 5: Plain washers |
| EN 14831:2005 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| EN 14399-6:2015 | High-strength structural bolting assemblies for preloading - Part 6: Plain chamfered washers |
| 15/30332554 DC : 0 | BS EN 14399-9 - HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| BS EN 14399-9:2009 | High strength structural bolting for preloading System HR or HV. Direct tension indicators for bolt and nut assemblies |
| I.S. EN 14399-9:2009 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 9: SYSTEM HR OR HV - DIRECT TENSION INDICATORS FOR BOLT AND NUT ASSEMBLIES |
| DIN EN 14399-5:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 5: PLAIN WASHERS |
| DIN EN 14399-1:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 1: GENERAL REQUIREMENTS |
| DIN EN 14399-6:2015-04 | HIGH-STRENGTH STRUCTURAL BOLTING ASSEMBLIES FOR PRELOADING - PART 6: PLAIN CHAMFERED WASHERS |
| DIN EN 14831:2005-07 | Fasteners - Tightening performance - Torque/Angle simplified test method |
| ISO 2692:2014 | Geometrical product specifications (GPS) Geometrical tolerancing Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 286-1:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits |
| ISO 286-2:2010 | Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts |
Sorry this product is not available in your region.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.