• There are no items in your cart

EN ISO 75-2:2013

Current
Current

The latest, up-to-date edition.

Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
Published date

04-17-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Apparatus
6 Test specimens
7 Conditioning
8 Procedure
9 Expression of results
10 Precision
11 Test report
Annex A (informative) - Precision
Bibliography

ISO 75-2:2013 specifies three methods, using different values of constant flexural stress, which can be used for the determination of the temperature of deflection under load of plastics (including filled plastics and fibre-reinforced plastics in which the fibre length, prior to processing, is up to 7,5 mm) and ebonite:method A, using a flexural stress of 1,80 MPa;method B, using a flexural stress of 0,45 MPa;method C, using a flexural stress of 8,00 MPa.

Committee
CEN/TC 249
DevelopmentNote
Supersedes PREN ISO 75-2. (04/2013)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current
Supersedes

I.S. EN 13121-3:2016 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
BS EN 16506:2014 Systems for renovation of drains and sewers. Lining with a rigidly anchored plastics inner layer (RAPL)
DIN EN 16506 E : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
05/30137614 DC : 0 ISO 18672-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
11/30239906 DC : 0 BS EN 15014 - PLASTICS PIPING SYSTEMS - BURIED AND ABOVE GROUND PIPING COMPONENTS FOR WATER AND OTHER LIQUIDS UNDER PRESSURE - REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR PIPES AND FITTINGS
13/30290552 DC : 0 BS EN 4691-1 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
DIN EN 16506:2014-12 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
BS EN 4702-05:2017 Aerospace series. Quick release fastening systems for non-structural and lining applications Retaining washer
03/102124 DC : 0 EN 14636-1 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
I.S. EN 4702-05:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 05: RETAINING WASHER
PREN 13160-7 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
PREN 4702-05 : DRAFT 2016 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 05: RETAINING WASHER
BS EN ISO 12215-1:2000 Small craft. Hull construction and scantlings Materials. Thermosetting resins, glass-fibre reinforcement, reference laminate
17/30359220 DC : 0 BS EN 15269-20 - EXTENDED APPLICATION OF TEST RESULTS FOR FIRE RESISTANCE AND/OR SMOKE CONTROL FOR DOOR, SHUTTER AND OPENABLE WINDOW ASSEMBLIES, INCLUDING THEIR ELEMENTS OF BUILDING HARDWARE - PART 20: SMOKE CONTROL FOR DOORS, SHUTTERS AND OPENABLE WINDOWS
DIN EN 13121-1:2003-10 GRP tanks and vessels for use above ground - Part 1: Raw materials; Specification conditions and acceptance conditions
DIN EN 14364 E : 2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
EN 13121-1:2003 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
DIN EN 14598-2:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
DIN EN 14598-1:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation
BS EN ISO 11542-2 : 1999 PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN ISO 1622-2:1999 Plastics. Polystrene (PS) moulding and extrusion materials Preparation of test specimens and determination of properties
BS EN 13677-2:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements
UNE-EN 16245-2:2014 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
BS EN ISO 2580-2:2003 Plastics. Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Preparation of test specimens and determination of properties
DIN EN 13923:2006-02 Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing
CEN/TS 15534-1:2007 Wood-plastics composites (WPC) - Part 1: Test methods for characterisation of WPC materials and products
EN 1115-1 : 1997 PLASTICS PIPING SYSTEMS FOR UNDERGROUND DRAINAGE AND SEWERAGE UNDER PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - PART 1: GENERAL
EN 13160-7:2016 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
EN 13121-3:2016 GRP tanks and vessels for use above ground - Part 3: Design and workmanship
PREN 14364 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
ONORM EN ISO 11542-2 : 2009 PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
UNE-EN 14636-1:2010 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
12/30266170 DC : 0 BS EN 15534-1 - COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1 : TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS
11/30239977 DC : 0 BS EN 16245-2 - FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: ADDITIONAL REQUIREMENTS FOR RESINS, CURING SYSTEMS, ADDITIVES AND MODIFIERS
DIN EN 16245-2:2013-08 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
NF EN 14636-1 : 2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
11/30246455 DC : 0 BS EN 1796 - PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
UNI EN 14364 : 2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
BS EN 15534-1 : 2014 COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS
EN 4702-05:2017 Aerospace series - Quick release fastening systems for non-structural and lining applications - Part 05: Retaining washer
14/30301266 DC : 0 BS EN 13160-7 - LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
DD CEN/TS 15534-1:2007 Wood-plastics composites (WPC) Test methods for characterisation of WPC materials and products
06/30150269 DC : 0 EN 14636-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
PREN 4691-1 : DRAFT 2015 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
I.S. EN 62052-21:2004 ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT
UNI EN 1796 : 2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
EN 50470-1:2006 Electricity metering equipment (a.c.) - Part 1: General requirements, tests and test conditions - Metering equipment (class indexes A, B and C)
BS EN 62052-21 : 2004 ELECTRICITY METERING EQUIPMENT (A.C.) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT (IEC 62052-21:2004)
I.S. EN 13121-1:2003 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 1: RAW MATERIALS - SPECIFICATION CONDITIONS AND ACCEPTANCE CONDITIONS
DIN EN 14364:2013-05 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
BS EN ISO 15526-2:2004 Plastics. Polyketone (PK) moulding and extrusion materials Preparation of test specimens and determination of properties
DIN EN ISO 2580-2:2004-05 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN 13566-4:2002 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Lining with cured-in-place pipes
BS EN 14598-2:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements
I.S. EN ISO 15526-2:2004 PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN 13160-7:2016 LEAK DETECTION SYSTEMS - PART 7: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR INTERSTITIAL SPACES, LEAK DETECTION LININGS AND LEAK DETECTION JACKETS
DIN EN 1796:2013-05 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
I.S. EN ISO 4894-2:1999 PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN 13411-4:2011 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING
I.S. EN ISO 11542-2:1999 PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN 1796:2013 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
DIN EN ISO 15526-2:2004-10 PLASTICS - POLYKETONE (PK) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
I.S. EN 14364:2013 PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
DIN EN 13121-3:2016-10 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
EN ISO 11542-2:1998/AC:2008 PLASTICS - ULTRA-HIGH-MOLECULAR-WEIGHT POLYETHYLENE (PE-UHMW) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
UNI EN 13411-4 : 2011 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING
NF EN 13411-4 : 2011 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING
UNI EN 14636-1 : 2010 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
BS EN 4702-03:2017 Aerospace series. Quick release fastening systems for non-structural and lining applications Stud - quick-release and locking
PREN 16506 : DRAFT 2012 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
UNI EN 16506 : 2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
CEI EN 62052-21 : 2005 ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT
11/30246458 DC : 0 BS EN 14364 - PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
BS EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Manholes and inspection chambers
PREN 15269-20 : DRAFT 2017 EXTENDED APPLICATION OF TEST RESULTS FOR FIRE RESISTANCE AND/OR SMOKE CONTROL FOR DOOR, SHUTTER AND OPENABLE WINDOW ASSEMBLIES, INCLUDING THEIR ELEMENTS OF BUILDING HARDWARE - PART 20: SMOKE CONTROL FOR DOORS, SHUTTERS AND OPENABLE WINDOWS
BS ISO 7391-2 : 1996 AMD 10746 PLASTICS - POLYCARBONATE (PC) MOULDING AND EXTRUSION MATERIALS - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN 4702-03 : 2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
EN 1796:2013 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
PREN 4702-03 : DRAFT 2016 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS WITH NON METALLIC STUD FOR NON-STRUCTURAL APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
I.S. EN 50470-1:2006 ELECTRICITY METERING EQUIPMENT (A.C.) - PART 1: GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - METERING EQUIPMENT (CLASS INDEXES A, B AND C)
I.S. EN 4691-1:2017 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
I.S. EN 14636-1:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 1: PIPES AND FITTINGS WITH FLEXIBLE JOINTS
BS EN 13121-3:2016 GRP tanks and vessels for use above ground Design and workmanship
I.S. EN 16245-2:2013 FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS
UNE-EN 13121-3:2017 GRP tanks and vessels for use above ground - Part 3: Design and workmanship
UNE-EN 13411-4:2011 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints
UNE-EN 13160-7:2017 Leak detection systems - Part 7: Requirements and test/assessment methods for interstitial spaces, leak detection linings and leak detection jackets
DIN EN 13411-4 E : 2011 TERMINATIONS FOR STEEL WIRE ROPES - SAFETY - PART 4: METAL AND RESIN SOCKETING
DIN EN ISO 2897-2:2004-05 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN 13121-1:2003 GRP tanks and vessels for use above ground Raw materials. Specification conditions and acceptance conditions
EN ISO 14527-1 : 1999 Plastics - Urea-formaldehyde and urea/melamine-formaldehyde powder moulding compounds (UF- and UF/MF-PMCs) - Part 1: Designation system and basis for specifications (ISO 14527-1:1999)
EN 16506:2014 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
EN 16245-2:2013 Fibre-reinforced plastic composites - Declaration of raw material characteristics - Part 2: Specific requirements for resin, curing systems, additives and modifiers
UNI EN 16245-2 : 2013 FIBRE-REINFORCED PLASTIC COMPOSITES - DECLARATION OF RAW MATERIAL CHARACTERISTICS - PART 2: SPECIFIC REQUIREMENTS FOR RESIN, CURING SYSTEMS, ADDITIVES AND MODIFIERS
12/30275810 DC : 0 BS EN 16506 - SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
EN 4691-1:2017 Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification
I.S. EN 13566-4:2003 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NON-PRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 4: LINING WITH CURED-IN-PLACE PIPES
14/30298583 DC : 0 BS EN 13121-3 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
BS EN 16245-2:2013 Fibre-reinforced plastic composites. Declaration of raw material characteristics Specific requirements for resin, curing systems, additives and modifiers
PREN 14636-2 : DRAFT 2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
BS EN 14636-1:2009 Plastics piping systems for non-pressure drainage and sewerage. Polyester resin concrete (PRC) Pipes and fittings with flexible joints
09/30203307 DC : DRAFT JULY 2009 BS EN 14636-2 - PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
DD CEN/TS 15534-2:2007 Wood-plastics composites (WPC) Characterisation of WPC materials
08/30180918 DC : DRAFT JULY 2008 BS EN 1854 - PRESSURE SENSING DEVICES FOR GAS BURNERS AND GAS BURNING APPLIANCES
01/121060 DC : DRAFT MAR 2001 PREN 13121-3 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
I.S. EN 14636-2:2009 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
BS EN 50470-1 : 2006 ELECTRICITY METERING EQUIPMENT (A.C.) - PART 1: GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - METERING EQUIPMENT (CLASS INDEXES A, B AND C)
EN 60598-1:2015/A1:2018 LUMINAIRES - PART 1: GENERAL REQUIREMENTS AND TESTS
S.R. CEN/TS 15534-2:2007 WOOD-PLASTICS COMPOSITES (WPC) - PART 2: CHARACTERISATION OF WPC MATERIALS
DIN EN ISO 11542-2:2010-01 Plastics - Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 11542-2:1998 + Cor. 1:2007) (includes Corrigendum AC:2008)
02/124520 DC : DRAFT DEC 2002 EN 14598-3 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 3: SPECIFIC REQUIREMENTS
UNE-EN 1796:2014 Plastics piping systems for water supply with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
BS EN 12576:1998 Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC
BS EN 13923:2005 Filament-wound FRP pressure vessels. Materials, design, manufacturing and testing
BS EN 13677-3:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements
BS EN ISO 3672-2:2001 Plastics. Unsaturated-polyester resins (UP-R) Preparation of test specimens and determination of properties
BS EN 13160-7:2003 Leak detection systems General requirements and test methods for interstitial spaces, leak protecting linings and leak protecting jackets
BS EN ISO 10366-2:2003 Plastics. Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Preparation of test specimens and determination of properties
BS EN 1796:2013 Plastics piping systems for water supply with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP)
ISO 2580-2:2003 Plastics Acrylonitrile-butadiene-styrene (ABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 4894-2:1995 Plastics Styrene/acrylonitrile (SAN) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 3672-2:2000 Plastics — Unsaturated-polyester resins (UP-R) — Part 2: Preparation of test specimens and determination of properties
BS EN 1115-1:2001 Plastics piping systems for underground drainage and sewerage under pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) General
BS EN 13411-4:2011 Terminations for steel wire ropes. Safety Metal and resin socketing
ISO 6402-2:2003 Plastics Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 11542-2:1998 Plastics Ultra-high-molecular-weight polyethylene (PE-UHMW) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 10366-2:2003 Plastics Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
UNE-EN 14364:2015 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
BS EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure. Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP). Specifications for pipes, fittings and joints
BS EN ISO 6402-2:2003 Plastics. Acrylonitrile-styrene-acrylate (ASA), acrylonitrile-(ethylene-propylene-diene)-styrene (AEPDS) and acrylonitrile-(chlorinated polyethylene)-styrene (ACS) moulding and extrusion materials Preparation of test specimens and determination of properties
BS EN 4691-1:2017 Aerospace series. Tie rod with integrated bolts Technical specification
EN ISO 15252-1 : 1999 PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
EN ISO 15252-2 : 1999 PLASTICS - EPOXY POWDER MOULDING COMPOUNDS (EP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
EN 13677-3:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements
EN 13677-2:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements
EN ISO 14529-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 15526-2:2004 Plastics - Polyketone (PK) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 15526-2:2000)
EN ISO 10366-2 : 2003 PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 3672-2 : 2001 PLASTICS - UNSATURATED-POLYESTER RESINS (UP-R) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 2580-2 : 2003 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 14530-2 : 1999 PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 2 - PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 14528-2 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 4894-2 : 1999 PLASTICS - STYRENE/ACRYLONITRILE (SAN) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 14528-1 : 1999 PLASTICS - MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (MF-PMCS) - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
EN 13923:2005 Filament-wound FRP pressure vessels - Materials, design, manufacturing and testing
EN ISO 14529-1 : 1999 PLASTICS - MELAMINE/PHENOLIC POWDER MOULDING COMPOUNDS (MP-PMCS) - PART 1 - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
EN ISO 14526-1 : 1999 PLASTICS - PHENOLIC POWDER MOULDING COMPOUNDS (PF/PMCS) - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
EN 14598-1:2005 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 1: Designation
EN 14636-2:2009 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
EN ISO 6402-2 : 2003 PLASTICS - ACRYLONITRILE-STYRENE-ACRYLATE (ASA), ACRYLONITRILE-(ETHYLENE-PROPYLENE-DIENE)-STYRENE (AEPDS) AND ACRYLONITRILE-(CHLORINATED POLYETHYLENE)-STYRENE (ACS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 14527-2 : 1999 PLASTICS - UREA-FORMALDEHYDE AND UREA/MELAMINE-FORMALDEHYDE POWDER MOULDING COMPOUNDS (UF- AND UF/MF-PMCS) - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN ISO 14530-1 : 1999 PLASTICS - UNSATURATED-POLYESTER POWDER MOULDING COMPOUNDS (UP-PMCS) - PART 1 - DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS
PREN 1796 : DRAFT 2011 PLASTICS PIPING SYSTEMS FOR WATER SUPPLY WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP)
I.S. EN 4702-03:2017 AEROSPACE SERIES - QUICK RELEASE FASTENING SYSTEMS FOR NON-STRUCTURAL AND LINING APPLICATIONS - PART 03: STUD - QUICK-RELEASE AND LOCKING
DIN EN 14636-1:2010-04 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 1: Pipes and fittings with flexible joints; German version EN 14636-1:2009
NF EN 14636-2 : 2010 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
04/30046221 DC : 0 PREN 13121-3 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
DIN EN 14636-2:2010-04 Plastics piping systems for non-pressure drainage and sewerage - Polyester resin concrete (PRC) - Part 2: Manholes and inspection chambers
UNI EN 14636-2 : 2010 PLASTICS PIPING SYSTEMS FOR NON- PRESSURE DRAINAGE AND SEWERAGE - POLYESTER RESIN CONCRETE (PRC) - PART 2: MANHOLES AND INSPECTION CHAMBERS
02/124518 DC : DRAFT DEC 2002 EN 14598-1 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 1: DESIGNATION
CEI EN 62052-11 : 2003 ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 11: METERING EQUIPMENT
04/30091870 DC : DRAFT FEB 2004 BS EN ISO 12086-2 - PLASTICS - FLUOROPOLYMER DISPERSIONS AND MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
EN 14364:2013 Plastics piping systems for drainage and sewerage with or without pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Specifications for pipes, fittings and joints
UNE-EN 16506:2015 Systems for renovation of drains and sewers - Lining with a rigidly anchored plastics inner layer (RAPL)
I.S. EN 15534-1:2014 COMPOSITES MADE FROM CELLULOSE-BASED MATERIALS AND THERMOPLASTICS (USUALLY CALLED WOOD-POLYMER COMPOSITES (WPC) OR NATURAL FIBRE COMPOSITES (NFC)) - PART 1: TEST METHODS FOR CHARACTERISATION OF COMPOUNDS AND PRODUCTS
S.R. CEN TS 15534-1:2007 WOOD-PLASTICS COMPOSITES (WPC) - PART 1: TEST METHODS FOR CHARACTERISATION OF WPC MATERIALS AND PRODUCTS
I.S. EN 16506:2014 SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
DIN EN ISO 2580-2 E : 2004 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
BS EN 13199-3:2000 Packaging. Small load carrier systems Bond Stackable System (BSS)
BS EN ISO 1163-2:2000 Plastics. Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials Preparation of test specimens and determination of properties
ISO 15526-2:2000 Plastics Polyketone (PK) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
02/124519 DC : DRAFT DEC 2002 EN 14598-2 - REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
BS EN 14598-1:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Designation
EN 13566-4:2002 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes
DIN EN 13411-4:2011-06 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
EN 13199-3:2000 Packaging - Small Load Carrier Systems - Part 3: Bond Stackable System (BSS)
EN 62052-21:2004/A1:2017/AC:2018-04 ELECTRICITY METERING EQUIPMENT (AC) - GENERAL REQUIREMENTS, TESTS AND TEST CONDITIONS - PART 21: TARIFF AND LOAD CONTROL EQUIPMENT (IEC 62052-21:2004/A1:2016/COR1:2018)
EN 13411-4:2011 Terminations for steel wire ropes - Safety - Part 4: Metal and resin socketing
CEN/TS 15534-2:2007 Wood-plastics composites (WPC) - Part 2: Characterisation of WPC materials

ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
ISO 293:2004 Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 10350-1:2017 Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding materials
ISO 10724-1:1998 Plastics — Injection moulding of test specimens of thermosetting powder moulding compounds (PMCs) — Part 1: General principles and moulding of multipurpose test specimens
ISO 5725:1986 Precision of test methods Determination of repeatability and reproducibility for a standard test method by inter-laboratory tests
ISO 294-1:2017 Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 2818:1994 Plastics — Preparation of test specimens by machining
ISO 20753:2008 Plastics Test specimens

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.