• There are no items in your cart

HD 60364-4-41:2017/A11:2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-41: PROTECTION FOR SAFETY - PROTECTION AGAINST ELECTRIC SHOCK
Superseded date

03-22-2022

Published date

08-11-2017

European foreword
410 Introduction
411 Protective measure: automatic disconnection of supply
412 Protective measure: double or reinforced insulation
413 Protective measure: electrical separation
414 Protective measure: extra-low-voltage provided by
    SELV and PELV
415 Additional protection
Annex A (normative) - Provisions for basic protection
        (protection against direct contact)
Annex B (normative) - Obstacles and placing out of reach
Annex C (normative) - Protective measures for application
        only when the installation is controlled or under the
        supervision of skilled or instructed persons
Annex D (normative) - Provisions where automatic
        disconnection according to 411.3.2 is not feasible
Annex E (informative) - List of notes concerning certain
        countries
Bibliography
Annex ZA (normative) - Special national conditions
Annex ZB (informative) - A-deviations for Denmark

Specifies essential requirements regarding protection against electric shock, including basic protection (protection against direct contact) and fault protection (protection against indirect contact) of persons and livestock.

Committee
TC 64
DevelopmentNote
Supersedes HD 384.4.41, HD 384.4.46 and HD 384.4.47. (02/2007)
DocumentType
Standard
PublisherName
European Committee for Standards - Electrical
Status
Superseded
Supersedes

I.S. HD 60364-7-753:2014 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-753: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - HEATING CABLES AND EMBEDDED HEATING SYSTEMS
BS EN 60669-2-5:2016 Switches for household and similar fixed electrical installations Particular requirements. Switches and related accessories for use in home and building electronic systems (HBES)
UNE-HD 60364-4-442:2013 Low-voltage electrical installations - Part 4-442: Protection for safety - Protection of low-voltage installations against temporary overvoltages due to earth faults in the high-voltage system and due to faults in the low voltage system
I.S. EN 62838:2016 LEDSI LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES NOT EXCEEDING 50 V A.C. R.M.S. OR 120 V RIPPLE FREE D.C. - SAFETY SPECIFICATIONS
UNE-EN 50272-1:2011 Safety requirements for secondary batteries and battery installations - Part 1: General safety information
S.R. HD 60364-5-557:2013 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-557: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - AUXILIARY CIRCUITS
EN 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
NF EN 50122-1 : 2011 AMD 4 2018 RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRICAL SAFETY, EARTHING AND THE RETURN CIRCUIT - PART 1: PROTECTIVE PROVISIONS AGAINST ELECTRIC SHOCK
S.R. HD 60364-5-51:2009 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES
S.R. HD 60364-4-42:2011 LOW VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-42: PROTECTION FOR SAFETY - PROTECTION AGAINST THERMAL EFFECTS
I.S. EN 50491-3:2009 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 3: ELECTRICAL SAFETY REQUIREMENTS
I.S. EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012 (EQV))
I.S. EN 12649:2008 CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY
I.S. HD 60364-7-702:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-702: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - SWIMMING POOLS AND FOUNTAINS
I.S. EN 60204-31:2013 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 31: PARTICULAR SAFETY AND EMC REQUIREMENTS FOR SEWING MACHINES, UNITS AND SYSTEMS (IEC 60204-31:2013 (EQV))
I.S. HD 60364-7-715:2005 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-715: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - EXTRA-LOW-VOLTAGE LIGHTING INSTALLATIONS (IEC 60364-7-715:2011 (MOD))
S.R. HD 60364-7-715:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-715: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - EXTRA-LOW-VOLTAGE LIGHTING INSTALLATIONS
I.S. EN 60309-2:1999 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES (IEC 60309-2:1999 (EQV))
BS EN 50153 : 2014 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
S.R. HD 60364-7-729:2009 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-729: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - OPERATING OR MAINTENANCE GANGWAYS
I.S. EN 62271-212:2017 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 212: COMPACT EQUIPMENT ASSEMBLY FOR DISTRIBUTION SUBSTATION (CEADS)
I.S. EN IEC 62485-1:2018 SAFETY REQUIREMENTS FOR SECONDARY BATTERIES AND BATTERY INSTALLATIONS - PART 1: GENERAL SAFETY INFORMATION
UNE-HD 60364-7-702:2013 Low-voltage electrical installations -- Part 7-702: Requirements for special installations or locations - Swimming pools and fountains
I.S. EN 50522:2010 EARTHING OF POWER INSTALLATIONS EXCEEDING 1 KV A.C.
BS EN 62026-2:2013 Low-voltage switchgear and controlgear. Controller-device interfaces (CDIs) Actuator sensor interface (AS-i)
BS EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing General requirements
13/30280057 DC : 0 BS EN 13782 - TEMPORARY STRUCTURE - TENTS - SAFETY
UNE-EN 62271-212:2017 High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Substation (CEADS)
17/30338554 DC : 0 BS EN 1175 - SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
BS EN 1398:2009 Dock levellers. Safety requirements
12/30235286 DC : DRAFT APR 2012 BS EN 50153 - RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
UNI EN 81-22 : 2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 22: ELECTRIC LIFTS WITH INCLINED PATH
BS EN 50272-1:2010 Safety requirements for secondary batteries and battery installations General safety information
BS EN 61557-8:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures Insulation monitoring devices for IT systems
UNE-EN 61140:2017 Protection against electric shock - Common aspects for installation and equipment
BS EN 50522:2010 Earthing of power installations exceeding 1 kV a.c.
UNE-EN 62870:2016 Electrical installations for lighting and beaconing of aerodromes - Safety secondary circuits in series circuits - General safety requirements
BS EN 50491-6-1:2014 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) HBES installations. Installation and planning
BS EN 60519-11:2007 Safety in electroheat installations Particular requirements for installations using the effect of electromagnetic forces on liquid metals
BS EN 62477-1 : 2012 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012)
CLC/TR 60269-5:2011 Low-voltage fuses - Part 5: Guidance for the application of low-voltage fuses
EN 50272-1:2010 Safety requirements for secondary batteries and battery installations - Part 1: General safety information
EN 61158-2:2014 Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition
EN 62838:2016/AC:2017-11 LEDSI LAMPS FOR GENERAL LIGHTING SERVICES WITH SUPPLY VOLTAGES NOT EXCEEDING 50 V A.C. R.M.S. OR 120 V RIPPLE FREE D.C. - SAFETY SPECIFICATIONS
HD 60364-5-51:2009/A12:2017 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES
EN 61347-2-13:2014/A1:2017 LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES
HD 60364-7-729:2009/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-729: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - OPERATING OR MAINTENANCE GANGWAYS
HD 60364-7-717:2010/AC:2014 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-717: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - MOBILE OR TRANSPORTABLE UNITS
BS 7671(2008) : 2018 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
EN 50191:2010 ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT
EN 60519-1:2015 Safety in installations for electroheating and electromagnetic processing - Part 1: General requirements
HD 60364-7-714:2012 Low-voltage electrical installations - Part 7-714: Requirements for special installations or locations - External lighting installations
HD 60364-5-534:2016 Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control - Clause 534: Devices for protection against transient overvoltages
EN 62271-212:2017 High-voltage switchgear and controlgear - Part 212: Compact Equipment Assembly for Distribution Substation (CEADS)
EN 60669-2-5:2016 Switches for household and similar fixed electrical installations - Part 2-5: Particular requirements - Switches and related accessories for use in home and building electronic systems (HBES)
EN 61131-2:2007 Programmable controllers - Part 2: Equipment requirements and tests
EN 61851-1:2011 Electric vehicle conductive charging system - Part 1: General requirements
HD 60364-4-42 : 2011 AMD 1 2015 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-42: PROTECTION FOR SAFETY - PROTECTION AGAINST THERMAL EFFECTS (IEC 60364-4-42:2010/A1:2014)
EN IEC 62485-2:2018 Safety requirements for secondary batteries and battery installations - Part 2: Stationary batteries
EN 62253 : 2011 PHOTOVOLTAIC PUMPING SYSTEMS - DESIGN QUALIFICATION AND PERFORMANCE MEASUREMENTS
EN 61558-2-16:2009/A1:2013 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013)
EN 62271-202:2014/AC:2014 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION (IEC 62271-202:2014)
HD 60364-7-702:2010 Low-voltage electrical installations - Part 7-702: Requirements for special installations or locations - Swimming pools and fountains
HD 60364-5-52:2011/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-52: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - WIRING SYSTEMS
HD 60364-5-557:2013/A11:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-557: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - AUXILIARY CIRCUITS
HD 60364-4-43:2010 Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
EN 12649:2008+A1:2011 Concrete compactors and smoothing machines - Safety
HD 60364-5-54:2011/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
HD 60364-5-559:2012/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-559: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - LUMINAIRES AND LIGHTING INSTALLATIONS
CEI EN 62135-1 : 2016 RESISTANCE WELDING EQUIPMENT - PART 1: SAFETY REQUIREMENTS FOR DESIGN, MANUFACTURE AND INSTALLATION
UNE-EN 50122-1:2011 Railway applications - Fixed installations - Electrical safety, earthing and the return circuit -- Part 1: Protective provisions against electric shock
I.S. EN 45510-2-9:2008 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS
BS EN 62282-5-1:2012 Fuel cell technologies Portable fuel cell power systems. Safety
S.R. HD 60364-5-534:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - ISOLATION, SWITCHING AND CONTROL - CLAUSE 534: DEVICES FOR PROTECTION AGAINST TRANSIENT OVERVOLTAGES
HD 60364-7-704:2018 Low voltage electrical installations - Part 7-704: Requirements for special installations or locations - Construction and demolition site installations
I.S. EN 50491-6-1:2014 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 6-1: HBES INSTALLATIONS - INSTALLATION AND PLANNING
I.S. HD 60364-5-559:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-559: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - LUMINAIRES AND LIGHTING INSTALLATIONS (IEC 60364-5-55:2011 (MOD))
I.S. EN 60669-2-5:2016 SWITCHES FOR HOUSEHOLD AND SIMILAR FIXED ELECTRICAL INSTALLATIONS - PART 2-5: PARTICULAR REQUIREMENTS - SWITCHES AND RELATED ACCESSORIES FOR USE IN HOME AND BUILDING ELECTRONIC SYSTEMS (HBES)
I.S. EN 62477-1:2012 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL
I.S. EN 62485-3:2014 SAFETY REQUIREMENTS FOR SECONDARY BATTERIES AND BATTERY INSTALLATIONS - PART 3: TRACTION BATTERIES
I.S. HD 60364-4-42:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-42: PROTECTION FOR SAFETY - PROTECTION AGAINST THERMAL EFFECTS
EN 50174-2 : 2009 AMD 2 2014 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
S.R. HD 60364-6:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 6: VERIFICATION
I.S. EN 50550:2011 POWER FREQUENCY OVERVOLTAGE PROTECTIVE DEVICE FOR HOUSEHOLD AND SIMILAR APPLICATIONS (POP)
I.S. EN 50122-1:2011 RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRICAL SAFETY, EARTHING AND THE RETURN CIRCUIT - PART 1: PROTECTIVE PROVISIONS AGAINST ELECTRIC SHOCK
S.R. HD 60364-7-730:2015 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-730: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - ONSHORE UNITS OF ELECTRICAL SHORE CONNECTIONS FOR INLAND NAVIGATION VESSELS
I.S. EN 61558-2-16:2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS
I.S. EN 50156-1:2015 ELECTRICAL EQUIPMENT FOR FURNACES AND ANCILLARY EQUIPMENT - PART 1: REQUIREMENTS FOR APPLICATION DESIGN AND INSTALLATION
I.S. HD 60364-7-729:2009 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-729: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - OPERATING OR MAINTENANCE GANGWAYS
I.S. HD 60364-7-701:2007 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-701: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - LOCATIONS CONTAINING A BATH OR SHOWER (IEC 60364-7-701:2006, MODIFIED)
I.S. EN 62271-202:2014 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 202: HIGH-VOLTAGE/LOW-VOLTAGE PREFABRICATED SUBSTATION
EN 60204-1 : 2006 COR 2010 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
I.S. EN IEC 62485-2:2018 SAFETY REQUIREMENTS FOR SECONDARY BATTERIES AND BATTERY INSTALLATIONS - PART 2: STATIONARY BATTERIES
S.R. HD 60364-7-712:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-712: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - PHOTOVOLTAIC (PV) SYSTEMS
EN 81-22:2014 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
EN 50310:2016 Telecommunications bonding networks for buildings and other structures
I.S. EN 60204-32:2008 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
I.S. EN 61800-5-1:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
DIN EN 1398:2009-07 DOCK LEVELLERS - SAFETY REQUIREMENTS
DIN EN 81-20 E : 2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 20: PASSENGER AND GOODS PASSENGER LIFTS
UNE-HD 60364-7-729:2011 Low-voltage electrical installations -- Part 7-729: Requirements for special installations or locations - Operating or maintenance gangways
DIN EN 15011:2014-09 Cranes - Bridge and gantry cranes (includes Amendment A1:2014)
BS EN 61131-2:2007 Programmable controllers Equipment requirements and tests
UNE-HD 60364-4-444:2013 Low-voltage electrical installations -- Part 4-444: Protection for safety - Protection against voltage disturbances and electromagnetic disturbances
BS EN 62485-3:2014 Safety requirements for secondary batteries and battery installations Traction batteries
UNE-EN 50310:2016 Telecommunications bonding networks for buildings and other structures
BS EN 62253:2011 Photovoltaic pumping systems. Design qualification and performance measurements
UNE-EN 81-20:2017 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 20: Passenger and goods passenger lifts
UNE-EN 15869-2:2011 Inland navigation vessels - Electrical shore connection, three phase current 400 V, up to 63 A, 50 Hz - Part 2: Onshore unit, safety requirements
DIN EN 15869-2:2010-06 INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREE PHASE CURRENT 400 V, UP TO 63 A, 50 HZ - PART 2: ONSHORE UNIT, SAFETY REQUIREMENTS
EN 15011:2011+A1:2014 Cranes - Bridge and gantry cranes
I.S. EN 61918:2013 INDUSTRIAL COMMUNICATION NETWORKS - INSTALLATION OF COMMUNICATION NETWORKS IN INDUSTRIAL PREMISES
EN 60079-14:2014/AC:2016 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION (IEC 60079-14:2013/COR1:2016)
I.S. EN 1398:2009 DOCK LEVELLERS - SAFETY REQUIREMENTS
EN 61557-8:2015/AC:2016-06 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems
CEI EN 50522 : 2011 EARTHING OF POWER INSTALLATIONS EXCEEDING 1 KV A.C.
VDI 2381 Blatt 2:2009-07 Final inspection of mobile cranes - Instructional form for experts
VDI 4068 Blatt 6:2011-10 Competent persons - Mobile elevating work platforms
VDI 2083 Blatt 17:2013-06 Cleanroom technology - Compatibility of materials with the required cleanliness
VDI 4068 Blatt 4:2011-04 Competent persons - Requirements for external training for the testing of handheld electric operated tools
VDI 4068 Blatt 8:2013-04 Competent Persons - Storage equipment and rack serving units
VDI 2166 Blatt 2:2015-10 Planning of electrical installations in buildings - Advice for electric mobility
DIN EN 50153 : 2018 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
VDI 4068 Blatt 5:2011-06 Competent Persons - Industrial trucks, attachments, trailers
VDE 0115-2 : 2018 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
KTA 3504 : 2015(R2017)
VDI 3551:2011-01 Electromagnetic compatibility (EMC) in building services
KTA 3403 : 2015(R2017) CABLE PENETRATIONS THROUGH THE REACTOR CONTAINMENT VESSEL OF NUCLEAR POWER PLANTS
06/30146388 DC : DRAFT FEB 2006 CENELEC TS 61643-12 - LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 12: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - SELECTION AND APPLICATION PRINCIPLES
11/30251717 DC : 0 BS EN 81-20 - SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 20: PASSENGER AND GOODS PASSENGER LIFTS
I.S. EN 62026-2:2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I) (IEC 62026-2:2008 (MOD))
08/30191664 DC : DRAFT OCT 2008 BS EN 50522 - EARTHING OF POWER INSTALLATIONS EXCEEDING 1 KV A.C.
EN 115-1:2017 Safety of escalators and moving walks - Part 1: Construction and installation
07/30152812 DC : DRAFT AUG 2007 BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
I.S. EN 60598-1:2015 LUMINAIRES - PART 1: GENERAL REQUIREMENTS AND TESTS
16/30328759 DC : 0 BS EN 13814-1 - SAFETY OF AMUSEMENT RIDES AND AMUSEMENT DEVICES - PART 1: DESIGN AND MANUFACTURE
I.S. EN 61158-2:2014 INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION
I.S. EN 115-1:2017 SAFETY OF ESCALATORS AND MOVING WALKS - PART 1: CONSTRUCTION AND INSTALLATION
I.S. HD 60364-5-52:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-52: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - WIRING SYSTEMS
S.R. HD 60364-5-551:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-55: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - OTHER EQUIPMENT - CLAUSE 551: LOW-VOLTAGE GENERATING SETS
I.S. EN 61009-1:2012 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
I.S. EN 61439-1:2011 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: GENERAL RULES (IEC 61439-1:2011)
I.S. HD 60364-7-714:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-714: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - EXTERNAL LIGHTING INSTALLATIONS (IEC 60364-7-714:2011 (EQV))
BS EN 60598-1:2015 Luminaires General requirements and tests
I.S. EN 50272-1:2010 SAFETY REQUIREMENTS FOR SECONDARY BATTERIES AND BATTERY INSTALLATIONS - PART 1: GENERAL SAFETY INFORMATION
UNE-EN 60669-2-5:2017 Switches for household and similar fixed electrical installations - Part 2-5: Particular requirements - Switches and related accessories for use in home and building electronic systems (HBES)
I.S. EN 50310:2016 TELECOMMUNICATIONS BONDING NETWORKS FOR BUILDINGS AND OTHER STRUCTURES
S.R. CLC/TS 61643-12:2009 LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 12: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER DISTRIBUTION SYSTEMS - SELECTION AND APPLICATION PRINCIPLES
ISO/TR 14799-1:2015 Comparison of worldwide escalator and moving walk safety standards Part 1: Rule by rule comparison
I.S. EN 61984:2009 CONNECTORS - SAFETY REQUIREMENTS AND TESTS
I.S. EN 50153:2014 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
I.S. EN 50191:2010 ERECTION AND OPERATION OF ELECTRICAL TEST EQUIPMENT
I.S. EN 61851-1:2011 ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM - PART 1: GENERAL REQUIREMENTS
I.S. EN 60204-1:2006 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
UNI EN 81-20 : 2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 20: PASSENGER AND GOODS PASSENGER LIFTS
DIN EN 12649:2011-09 Concrete compactors and smoothing machines - Safety
UNE-EN 62271-202:2015 High-voltage switchgear and controlgear - Part 202: High-voltage/low-voltage prefabricated substation
UNE-HD 60364-7-712:2017 Low-voltage electrical installations - Part 7-712: Requirements for special installations or locations - Photovoltaic (PV) systems
UNE-EN 60079-14:2016 Explosive atmospheres - Part 14: Electrical installations design, selection and erection
UNE-EN 61557-8:2016 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems
UNE-HD 60364-7-710:2014 Low-voltage electrical installations - Part 7-710: Requirements for special installations or locations - Medical locations
DD CLC/TS 61643-12:2009 Low-voltage surge protective devices Surge protective devices connected to low-voltage power distribution systems. Selection and application principles
BS EN 81-22:2014 Safety rules for the construction and installation of lifts. Lifts for the transport of persons and goods Electric lifts with inclined path
UNE-EN 81-22:2014 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
BS EN 60079-14:2014 Explosive atmospheres Electrical installations design, selection and erection
EN 61009-1:2012/A12:2016 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
BS EN 12649 : 2008 CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY
UNE-EN 50521:2010 Connectors for photovoltaic systems - Safety requirements and tests
CEI EN 60519-1 : 2016 SAFETY IN INSTALLATIONS FOR ELECTROHEATING AND ELECTROMAGNETIC PROCESSING - PART 1: GENERAL REQUIREMENTS
UNE-HD 60364-5-53:2016 Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Switchgear and controlgear
CEI EN 62026-2 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I)
UNE-EN 61535:2010 Installation couplers intended for permanent connection in fixed installations
UNI EN 1398 : 2009 DOCK LEVELLERS - SAFETY REQUIREMENTS
UNI EN 12649 : 2011 CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY
EN 50532:2010 Compact Equipment Assembly for Distribution Substations (CEADS)
UNI EN 15869-2 : 2010 INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREE-PHASE CURRENT 400 V, UP TO 63 A, 50 HZ - PART 2: ONSHORE UNIT, SAFETY REQUIREMENTS
EN 45510-2-9:2008 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS
PREN 1175 : DRAFT 2017 SAFETY OF INDUSTRIAL TRUCKS - ELECTRICAL/ELECTRONIC REQUIREMENTS
I.S. EN 50532:2010 COMPACT EQUIPMENT ASSEMBLY FOR DISTRIBUTION SUBSTATIONS (CEADS)
14/30316181 DC : 0 BS EN 50628 - ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES
NF EN 50491-3 : 2011 GENERAL REQUIREMENTS FOR HOME AND BUILDING ELECTRONIC SYSTEMS (HBES) AND BUILDING AUTOMATION AND CONTROL SYSTEMS (BACS) - PART 3: ELECTRICAL SAFETY REQUIREMENTS
BS EN 60309-2 : 1999 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES
I.S. EN 15869-2:2010 INLAND NAVIGATION VESSELS - ELECTRICAL SHORE CONNECTION, THREE PHASE CURRENT 400 V, UP TO 63 A, 50 HZ - PART 2: ONSHORE UNIT, SAFETY REQUIREMENTS
I.S. EN 50628:2016 ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES
S.R. HD 60364-5-53:2015 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
I.S. HD 60364-5-51:2009 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 5-51: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - COMMON RULES (IEC 60364-5-51:2005 (MOD))
I.S. EN 50174-2:2009 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
S.R. HD 60364-5-559:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-559: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - LUMINAIRES AND LIGHTING INSTALLATIONS
S.R. HD 60364-5-54:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
I.S. EN 62870:2015 ELECTRICAL INSTALLATIONS FOR LIGHTING AND BEACONING OF AERODROMES - SAFETY SECONDARY CIRCUITS IN SERIES CIRCUITS - GENERAL SAFETY REQUIREMENTS
S.R. HD 60364-5-52:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-52: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - WIRING SYSTEMS
I.S. HD 60364-5-534:2008 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - ISOLATION, SWITCHING AND CONTROL - CLAUSE 534: DEVICES FOR PROTECTION AGAINST OVERVOLTAGES
I.S. EN 60601- 1:2006&A1:2013&AC:2014&A12:2014 MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE
PREN 50628 : DRAFT 2014 ERECTION OF ELECTRICAL INSTALLATIONS IN UNDERGROUND MINES
EN 60598-1:2015/A1:2018 LUMINAIRES - PART 1: GENERAL REQUIREMENTS AND TESTS
EN 50550:2011/A1:2014 POWER FREQUENCY OVERVOLTAGE PROTECTIVE DEVICE FOR HOUSEHOLD AND SIMILAR APPLICATIONS (POP)
ISO/TR 14799-2:2015 Comparison of worldwide escalator and moving walk safety standards — Part 2: Abbreviated comparison and comments
UNE-EN 60598-1:2015 Luminaires - Part 1: General requirements and tests
EN 62026-2:2013 Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)
I.S. EN 62135-1:2015 RESISTANCE WELDING EQUIPMENT - PART 1: SAFETY REQUIREMENTS FOR DESIGN, MANUFACTURE AND INSTALLATION
I.S. HD 60364-7-740:2006 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 7-740: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - TEMPORARY ELECTRICAL INSTALLATIONS FOR STRUCTURES, AMUSEMENT DEVICES AND BOOTHS AT FAIRGROUNDS, AMUSEMENT PARKS AND CIRCUSES
I.S. HD 60364-4-444:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-444: PROTECTION FOR SAFETY - PROTECTION AGAINST VOLTAGE DISTURBANCES AND ELECTROMAGNETIC DISTURBANCES
I.S. EN 61131-2:2007 PROGRAMMABLE CONTROLLERS - PART 2: EQUIPMENT REQUIREMENTS AND TESTS
I.S. EN 15011:2011 CRANES - BRIDGE AND GANTRY CRANES
I.S. HD 60364-5-551:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-55: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - OTHER EQUIPMENT - CLAUSE 551: LOW-VOLTAGE GENERATING SETS
S.R. CLC/TR 50480:2011 DETERMINATION OF CROSS-SECTIONAL AREA OF CONDUCTORS AND SELECTION OF PROTECTIVE DEVICES
I.S. HD 60364-4-43:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-43: PROTECTION FOR SAFETY - PROTECTION AGAINST OVERCURRENT
EN 50153 : 2014 AMD 1 2017 RAILWAY APPLICATIONS - ROLLING STOCK - PROTECTIVE PROVISIONS RELATING TO ELECTRICAL HAZARDS
DIN EN 61158-2:2015-02 INDUSTRIAL COMMUNICATION NETWORKS - FIELDBUS SPECIFICATIONS - PART 2: PHYSICAL LAYER SPECIFICATION AND SERVICE DEFINITION (IEC 61158-2:2014)
BS EN 62271-212:2017 High-voltage switchgear and controlgear Compact Equipment Assembly for Distribution Substation (CEADS)
BS EN 15869-2:2010 Inland navigation vessels. Electrical shore connection, three phase current 400 V, up to 63 A, 50 Hz Onshore unit, safety requirements
BS EN 60601-1 : 2006 MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE
BS EN 61558-2-16 : 2009 SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS
14/30302919 DC : 0 PD CEN/TR 81-12 - SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - BASICS AND INTERPRETATIONS - PART 12: USE OF EN 81-20 AND EN 81-50 IN SPECIFIC MARKETS
UNE-EN 61557-11:2010 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 11: Effectiveness of residual current monitors (RCMs) type A and type B in TT, TN and IT systems
BS EN 61158-2:2014 Industrial communication networks. Fieldbus specifications Physical layer specification and service definition
UNE-EN 50522:2012 Earthing of power installations exceeding 1 kV a.c.
BS EN 61347-2-13 : 2014 LAMP CONTROLGEAR - PART 2-13: PARTICULAR REQUIREMENTS FOR D.C. OR A.C. SUPPLIED ELECTRONIC CONTROLGEAR FOR LED MODULES (IEC 61347-2-13:2014)
BS EN 61918:2013 Industrial communication networks. Installation of communication networks in industrial premises
BS EN 61984:2009 Connectors. Safety requirements and tests
BS EN 62838:2016 LEDsi lamps for general lighting services with supply voltages not exceeding 50 V a.c. r.m.s. or 120 V ripple free d.c. Safety specifications
UNE-EN 61009-1:2013 Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs) - Part 1: General rules
BS EN 61851-1:2011 Electric vehicle conductive charging system General requirements
BS EN 60204-31:2013 Safety of machinery. Electrical equipment of machines Particular safety and EMC requirements for sewing machines, units and systems
15/30324856 DC : 0 BS EN 115-1 - SAFETY OF ESCALATORS AND MOVING WALKS - PART 1: CONSTRUCTION AND INSTALLATION
BS EN 62282-4-101:2014 Fuel cell technologies Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU). Safety of electrically powered industrial trucks
PD CLC/TR 50480:2011 Determination of cross-sectional area of conductors and selection of protective devices
BS EN 50532:2010 Compact equipment assembly for distribution substations (CEADS)
UNE-EN 62253:2012 Photovoltaic pumping systems - Design qualification and performance measurements
BS EN 50491-3:2009 General requirements for home and building electronic systems (HBES) and building automation and control systems (BACS) Electrical safety requirements
17/30361391 DC : 0 BS EN 50174-2 - INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
UNE-EN 12649:2009 Concrete compactors and smoothing machines - Safety
UNE-EN 62838:2016 LEDsi lamps for general lighting services with supply voltages not exceeding 50 v a.c. r.m.s. or 120 v ripple free D.C. - Safety specifications
UNE-HD 60364-5-534:2016 Low-voltage electrical installations - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control - Clause 534: Devices for protection against transient overvoltages
UNE-HD 60364-6:2017 Low-voltage electrical installations - Part 6: Verification
BS EN 61140 : 2002 PROTECTION AGAINST ELECTRIC SHOCK - COMMON ASPECTS FOR INSTALLATION AND EQUIPMENT
UNE-EN 50491-3:2010 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 3: Electrical safety requirements
UNE-HD 60364-7-753:2015 Low-voltage electrical installations - Part 7-753: Requirements for special installations or locations - Heating cables and embedded heating systems
UNE-HD 60364-5-51:2010 Electrical installations of buildings -- Part 5-51: Selection and erection of electrical equipment - Common rules
BS EN 81-20:2014 Safety rules for the construction and installation of lifts. Lifts for the transport of persons and goods Passenger and goods passenger lifts
09/30202403 DC : 0 BS EN 50532 - COMPACT EQUIPMENT ASSEMBLY FOR DISTRIBUTION SUBSTATIONS (CEADS)
UNE-EN 50550:2012 Power frequency overvoltage protective device for household and similar applications (POP)
09/30212624 DC : 0 BS EN 50550 - POWER FREQUENCY OVERVOLTAGE PROTECTIVE DEVICE FOR HOUSEHOLD AND SIMILAR APPLICATIONS (POP)
BS EN 15011 : 2011 CRANES - BRIDGE AND GANTRY CRANES
UNE-EN 50532:2011 Compact Equipment Assembly for Distribution Substations (CEADS)
PD ISO/TR 14799-2:2005 Comparison of worldwide escalator and moving walk safety standards Abbreviated comparison and comments
BS EN 50521 : 2009 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
BS EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment Requirements for application design and installation
BS EN 60204-33:2011 Safety of machinery. Electrical equipment of machines Requirements for semiconductor fabrication equipment
BS EN 61009-1 : 2012 RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES (RCBOS) - PART 1: GENERAL RULES
BS EN 50310:2016 Telecommunications bonding networks for buildings and other structures
UNE-EN 62485-3:2015 Safety requirements for secondary batteries and battery installations - Part 3: Traction batteries
UNE-HD 60364-4-43:2013 Low-voltage electrical installations -- Part 4-43: Protection for safety - Protection against overcurrent
BS EN 50122-1 : 2011 RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRICAL SAFETY, EARTHING AND THE RETURN CIRCUIT - PART 1: PROTECTIVE PROVISIONS AGAINST ELECTRIC SHOCK
UNE-EN 60204-31:2013 Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems
EN 45510-2-9 : 2008 GUIDE FOR PROCUREMENT OF POWER STATION EQUIPMENT - PART 2-9: ELECTRICAL EQUIPMENT - CABLING SYSTEMS
EN 15869-2:2010 Inland navigation vessels - Electrical shore connection, three phase current 400 V, up to 63 A, 50 Hz - Part 2: Onshore unit, safety requirements
EN 1398:2009 Dock levellers - Safety requirements
I.S. HD 60364-7-717:2010 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-717: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - MOBILE OR TRANSPORTABLE UNITS
I.S. HD 60364-7-710:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-710: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - MEDICAL LOCATIONS (IEC 60364-7-710:2002 (MOD))
I.S. EN 81-22:2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 22: ELECTRIC LIFTS WITH INCLINED PATH
BS EN 50191:2010 Erection and operation of electrical test equipment
I.S. EN 60079-14:2014 EXPLOSIVE ATMOSPHERES - PART 14: ELECTRICAL INSTALLATIONS DESIGN, SELECTION AND ERECTION
NF EN 12649 : 2008 + A1 2011 CONCRETE COMPACTORS AND SMOOTHING MACHINES - SAFETY
S.R. HD 60364-4-46:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-46: PROTECTION FOR SAFETY - ISOLATION AND SWITCHING
I.S. EN 50521:2008 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
I.S. EN 62253:2011 PHOTOVOLTAIC PUMPING SYSTEMS - DESIGN QUALIFICATION AND PERFORMANCE MEASUREMENTS
I.S. HD 60364-5-54:2011 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
I.S. EN 81-20:2014 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 20: PASSENGER AND GOODS PASSENGER LIFTS
S.R. HD 60364-7-740:2006 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 7-740: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - TEMPORARY ELECTRICAL INSTALLATIONS FOR STRUCTURES, AMUSEMENT DEVICES AND BOOTHS AT FAIRGROUNDS, AMUSEMENT PARKS AND CIRCUSES
I.S. EN 60519-11:2007 SAFETY IN ELECTROHEAT INSTALLATIONS - PART 11: PARTICULAR REQUIREMENTS FOR INSTALLATIONS USING THE EFFECT OF ELECTROMAGNETIC FORCES ON LIQUID METALS
S.R. HD 60364-7-704:2007 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-704: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - CONSTRUCTION AND DEMOLITION SITE INSTALLATIONS
BS EN 115-1:2017 Safety of escalators and moving walks Construction and installation
S.R. CLC/TR 60269-5:2011 LOW-VOLTAGE FUSES - PART 5: GUIDANCE FOR THE APPLICATION OF LOW-VOLTAGE FUSES
I.S. EN 60204-33:2011 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 33: REQUIREMENTS FOR SEMICONDUCTOR FABRICATION EQUIPMENT
I.S. CLC TS 61643-12:2006 LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 12: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER SYSTEMS - SELECTION AND APPLICATION PRINCIPLES
I.S. EN 60519-1:2015 SAFETY IN INSTALLATIONS FOR ELECTROHEATING AND ELECTROMAGNETIC PROCESSING - PART 1: GENERAL REQUIREMENTS
EN 62477-1:2012/A1:2017 SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 1: GENERAL (IEC 62477-1:2012/A1:2016)
EN 61918:2013/AC:2014 INDUSTRIAL COMMUNICATION NETWORKS - INSTALLATION OF COMMUNICATION NETWORKS IN INDUSTRIAL PREMISES (IEC 61918:2013, MODIFIED)
DIN EN 81-22:2014-12 Safety rules for the construction and installation of lifts - Lifts for the transport of persons and goods - Part 22: Electric lifts with inclined path
UNE-EN 61439-1:2012 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
BS EN 50550 : 2011 POWER FREQUENCY OVERVOLTAGE PROTECTIVE DEVICE FOR HOUSEHOLD AND SIMILAR APPLICATIONS (POP)
BS EN 50174-2 : 2009 INFORMATION TECHNOLOGY - CABLING INSTALLATION - PART 2: INSTALLATION PLANNING AND PRACTICES INSIDE BUILDINGS
UNE-HD 60364-7-730:2016 Low-voltage electrical installations - Part 7-730: Requirements for special installations or locations - Onshore units of electrical shore connections for inland navigation vessels
BS EN 62135-1:2015 Resistance welding equipment Safety requirements for design, manufacture and installation
BS EN 45510-2-9:2008 Guide for procurement of power station equipment Electrical equipment. Cabling systems
BS EN 50628:2016 Erection of electrical installations in underground mines
10/30216944 DC : 0 BS EN 81-22 - SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR TRANSPORT OF PERSONS AND GOODS - PART 22: ELECTRIC LIFTS WITH INCLINED PATH
09/30205182 DC : 0 BS EN 50310 - APPLICATION OF EQUIPOTENTIAL BONDING AND EARTHING IN BUILDINGS WITH INFORMATION TECHNOLOGY EQUIPMENT
BS EN 61557-9:2015 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. Equipment for testing, measuring or monitoring of protective measures Equipment for insulation fault location in IT systems
BS EN 60204-1 : 2006 SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
BS EN 60204-32:2008 Safety of machinery. Electrical equipment of machines Requirements for hoisting machines
BS EN 61439-1:2011 Low-voltage switchgear and controlgear assemblies General rules
PD ISO/TR 14799-1:2005 Comparison of worldwide escalator and moving walk safety standards Rule by rule comparison
BS EN 62271-202:2014 High-voltage switchgear and controlgear High-voltage/low-voltage prefabricated substation
UNE-CLC/TS 61643-12:2012 Low-voltage surge protective devices -- Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles
17/30357380 DC : 0 BS EN 15011 - CRANES - BRIDGE AND GANTRY CRANES
HD 60364-7-710:2012/AC:2013 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-710: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - MEDICAL LOCATIONS
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
HD 60364-5-53:2015/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-53: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - SWITCHGEAR AND CONTROLGEAR
EN 50521:2008/A1:2012 CONNECTORS FOR PHOTOVOLTAIC SYSTEMS - SAFETY REQUIREMENTS AND TESTS
EN 62282-5-1:2012 FUEL CELL TECHNOLOGIES - PART 5-1: PORTABLE FUEL CELL POWER SYSTEMS - SAFETY (IEC 62282-5-1:2012)
BS 7671(2008) : 2008 REQUIREMENTS FOR ELECTRICAL INSTALLATIONS - IET WIRING REGULATIONS
EN 61984:2009 Connectors - Safety requirements and tests
EN 50522:2010 Earthing of power installations exceeding 1 kV a.c.
CLC/TR 50480:2011 Determination of cross-sectional area of conductors and selection of protective devices
EN 50491-6-1:2014 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 6-1: HBES installations - Installation and planning
EN 50156-1:2015 Electrical equipment for furnaces and ancillary equipment - Part 1: Requirements for application design and installation
EN 61557-9:2015/AC:2017-02 ELECTRICAL SAFETY IN LOW VOLTAGE DISTRIBUTION SYSTEMS UP TO 1000 V A.C. AND 1500 V D.C. - EQUIPMENT FOR TESTING, MEASURING OR MONITORING OF PROTECTIVE MEASURES - PART 9: EQUIPMENT FOR INSULATION FAULT LOCATION IN IT SYSTEMS (IEC 61557-9:2014/COR2:2017)
HD 60364-7-712:2016 Low-voltage electrical installations - Part 7-712: Requirements for special installations or locations - Photovoltaic (PV) systems
EN 62870:2015 Electrical installations for lighting and beaconing of aerodromes - Safety secondary circuits in series circuits - General safety requirements
HD 60364-7-740:2006/A11:2017 ELECTRICAL INSTALLATIONS OF BUILDINGS - PART 7-740: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - TEMPORARY ELECTRICAL INSTALLATIONS FOR STRUCTURES, AMUSEMENT DEVICES AND BOOTHS AT FAIRGROUNDS, AMUSEMENT PARKS AND CIRCUSES
EN 60204-31:2013 Safety of machinery - Electrical equipment of machines - Part 31: Particular safety and EMC requirements for sewing machines, units and systems
EN 60204-32:2008 Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines
HD 60364-6:2016/AC:2017-11 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 6: VERIFICATION (IEC 60364-6:2016/COR1:2017)
EN 50491-3:2009 General requirements for Home and Building Electronic Systems (HBES) and Building Automation and Control Systems (BACS) - Part 3: Electrical safety requirements
HD 60364-7-715:2012/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-715: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - EXTRA-LOW-VOLTAGE LIGHTING INSTALLATIONS
HD 60364-7-730:2015 Low-voltage electrical installations - Part 7-730: Requirements for special installations or locations - Onshore units of electrical shore connections for inland navigation vessels
HD 60364-4-444:2010/AC:2012 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-444: PROTECTION FOR SAFETY - PROTECTION AGAINST VOLTAGE DISTURBANCES AND ELECTROMAGNETIC DISTURBANCES
EN 60204-33:2011 Safety of machinery - Electrical equipment of machines - Part 33: Requirements for semiconductor fabrication equipment
HD 60364-5-551:2010/A11:2016 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-55: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - OTHER EQUIPMENT - CLAUSE 551: LOW-VOLTAGE GENERATING SETS
EN 62135-1:2015/AC:2016-02 RESISTANCE WELDING EQUIPMENT - PART 1: SAFETY REQUIREMENTS FOR DESIGN, MANUFACTURE AND INSTALLATION
EN 50628:2016 Erection of electrical installations in underground mines
DIN EN 81-20:2014-11 SAFETY RULES FOR THE CONSTRUCTION AND INSTALLATION OF LIFTS - LIFTS FOR THE TRANSPORT OF PERSONS AND GOODS - PART 20: PASSENGER AND GOODS PASSENGER LIFTS
EN IEC 62485-1:2018 Safety requirements for secondary batteries and battery installations - Part 1: General safety information
HD 60364-4-46:2016/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 4-46: PROTECTION FOR SAFETY - ISOLATION AND SWITCHING
DIN EN 12151:2008-05 MACHINERY AND PLANTS FOR THE PREPARATION OF CONCRETE AND MORTAR - SAFETY REQUIREMENTS
CLC/TS 61643-12 : 2009 LOW-VOLTAGE SURGE PROTECTIVE DEVICES - PART 12: SURGE PROTECTIVE DEVICES CONNECTED TO LOW-VOLTAGE POWER DISTRIBUTION SYSTEMS - SELECTION AND APPLICATION PRINCIPLES
EN 62282-4-101:2014 Fuel cell technologies - Part 4-101: Fuel cell power systems for propulsion other than road vehicles and auxiliary power units (APU) - Safety of electrically powered industrial trucks
HD 60364-7-701:2007/A12:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-701: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - LOCATIONS CONTAINING A BATH OR SHOWER
EN 50122-1:2011/A4:2017 RAILWAY APPLICATIONS - FIXED INSTALLATIONS - ELECTRICAL SAFETY, EARTHING AND THE RETURN CIRCUIT - PART 1: PROTECTIVE PROVISIONS AGAINST ELECTRIC SHOCK
EN 60309-2:1999/A2:2012 PLUGS, SOCKET-OUTLETS AND COUPLERS FOR INDUSTRIAL PURPOSES - PART 2: DIMENSIONAL INTERCHANGEABILITY REQUIREMENTS FOR PIN AND CONTACT-TUBE ACCESSORIES (IEC 60309-2:1999/A2:2012)
EN 60519-11:2007 Safety in electroheat installations - Part 11: Particular requirements for installations using the effect of electromagnetic forces on liquid metals
UNI EN 15011 : 2014 CRANES - BRIDGE AND GANTRY CRANES
HD 60364-4-442:2012 Low-voltage electrical installations - Part 4-442: Protection for safety - Protection of low-voltage installations against temporary overvoltages due to earth faults in the high-voltage system and due to faults in the low voltage system
EN 62485-3:2014 Safety requirements for secondary batteries and battery installations - Part 3: Traction batteries
HD 60364-7-753:2014/AC:2014 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 7-753: REQUIREMENTS FOR SPECIAL INSTALLATIONS OR LOCATIONS - HEATING CABLES AND EMBEDDED HEATING SYSTEMS (IEC 60364-7-753:2014)
UNE-HD 60364-4-46:2017 Low-voltage electrical installations - Part 4-46: Protection for safety - Isolation and switching
UNE-HD 60364-5-557:2014 Low-voltage electrical installations - Part 5-557: Selection and erection of electrical equipment - Auxiliary circuits
UNE-EN 15011:2011 Cranes - Bridge and gantry cranes
UNE-HD 60364-7-715:2013 Low-voltage electrical installations - Part 7-715: Requirements for special installations or locations - Extra-low-voltage lighting installations
UNE-HD 60364-4-42:2014 Low voltage electrical installations -- Part 4-42: Protection for safety - Protection against thermal effects
UNE-HD 60364-7-717:2013 Low-voltage electrical installations -- Part 7-717: Requirements for special installations or locations - Mobile or transportable units
UNE-HD 60364-5-551:2013 Low-voltage electrical installations -- Part 5-55: Selection and erection of electrical equipment - Other equipment -- Clause 551: Low-voltage generating sets
UNE-HD 60364-5-52:2014 Low-voltage electrical installations -- Part 5-52: Selection and erection of electrical equipment - Wiring systems
UNE-HD 60364-5-54:2015 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors

IEC 60364-5-54:2011 Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors
IEC 62423:2009 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses
IEC 60364-4-43:2008 Low-voltage electrical installations - Part 4-43: Protection for safety - Protection against overcurrent
IEC 61008-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCBs) - Part1: General rules
IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control
HD 60364-5-54:2011/A11:2017 LOW-VOLTAGE ELECTRICAL INSTALLATIONS - PART 5-54: SELECTION AND ERECTION OF ELECTRICAL EQUIPMENT - EARTHING ARRANGEMENTS AND PROTECTIVE CONDUCTORS
IEC 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
IEC 61009-1:2010+AMD1:2012+AMD2:2013 CSV Residual current operated circuit-breakers with integral overcurrentprotection for household and similar uses (RCBOs) - Part 1: General rules
IEC 60364-6:2016 Low voltage electrical installations - Part 6: Verification
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC GUIDE 104:2010 The preparation of safety publications and the use of basic safety publications and group safety publications
IEC 60146-2:1999 Semiconductor converters - Part 2: Self-commutated semiconductor converters including direct d.c. converters
IEC 60439-1:1999+AMD1:2004 CSV Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies
EN 60439-1:1999/A1:2004 LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES
IEC 62020:1998+AMD1:2003 CSV Electrical accessories - Residual current monitors for household and similar uses (RCMs)
EN 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 61557-9:2014 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 9: Equipment for insulation fault location in IT systems
EN 61558-2-6:2009 Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers
IEC 62477-1:2012+AMD1:2016 CSV Safety requirements for power electronic converter systems and equipment - Part 1: General
IEC 60947-2:2016 Low-voltage switchgear and controlgear - Part 2: Circuit-breakers
IEC 61140:2016 Protection against electric shock - Common aspects for installation and equipment
IEC 61557-8:2014 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 8: Insulation monitoring devices for IT systems
IEC 60364-5-52:2009 Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.