• There are no items in your cart

I.S. EN 12979:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

AUTOMOTIVE LPG-SYSTEMS - INSTALLATION REQUIREMENTS
Available format(s)

Hardcopy , PDF

Superseded date

06-27-2022

Language(s)

English

Published date

01-01-2002

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Installation requirements
  5.1 General requirements
  5.2 Connections to LPG-system
  5.3 LPG identification mark for M[2] and M[3] category
       vehicles
  5.4 Changes to the vehicle structure
  5.5 Container installation
  5.6 Installation of more than one container
  5.7 Components on or in the container
       5.7.1 General requirements
       5.7.2 Remote-controlled service valve with excess
              flow valve on the container
       5.7.3 Pressure relief valve
       5.7.4 Filling unit
       5.7.5 80 % stop valve
       5.7.6 Level indicator
       5.7.7 Gas-tight housing
  5.8 Gas pipes and hoses
  5.9 Gas connections between components of the LPG-system
  5.10 Remote-controlled shut-off valve
  5.11 Vehicle connector
  5.12 Electrical installation
  5.13 Fuel selection system
  5.14 Pressure relief device
  5.15 Installation manual
       5.15.1 General
       5.15.2 Contents of the installation manual
6 Markings in case of retrofit installation
Annex A (normative) Definitions of vehicle categories
        (extract from Directive 70/156)
   A.1 International classification of vehicle categories
   A.2 Load and checking conditions
Annex B (normative) Container fixing requirements up to a
        capacity of 150 litres
   B.1 General requirements
   B.2 Container frame
Annex C (normative) Arrangement of approval markings
   C.1 Type approval marking
   C.2 International country numbers
Annex D (normative) Provisions regarding the identification
        for M[2] and M[3] category vehicles
Annex E (normative) Provisions regarding the identification
        of the service coupling
Annex F (informative) Installation of more than one container
Bibliography

Describes the requirements for the installation of automotive LPG components that comply with prEN 12805 and prEN 12806.

DocumentType
Standard
Pages
28
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
NF EN 12979 : 2003 Identical
NBN EN 12979 : 2002 Identical
NEN EN 12979 : 2002 Identical
NS EN 12979 : 1ED 2002 Identical
UNE-EN 12979:2002 Identical
SN EN 12979 : 2002 Identical
UNI EN 12979 : 2004 Identical
BS EN 12979:2002 Identical
EN 12979:2002 Identical
DIN EN 12979:2002-04 Identical
ONORM EN 12979 : 2002 Identical

EN 589:2008+A1:2012 Automotive fuels - LPG - Requirements and test methods
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
ISO 630:1995 Structural steels Plates, wide flats, bars, sections and profiles
EN 60529:1991/AC:2016-12 DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread

View more information
US$64.68
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.