• There are no items in your cart

I.S. EN 1802:2002

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by
withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

TRANSPORTABLE GAS CYLINDERS - PERIODIC INSPECTION AND TESTING OF SEAMLESS ALUMINIUM ALLOY GAS CYLINDERS
Available format(s)

Hardcopy , PDF

Withdrawn date

03-22-2021

Language(s)

English

Published date

01-01-2002

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Intervals between periodic inspection and test
4 List of procedures for periodic inspection and test
5 Identification of cylinder and preparation for
   inspection and test
6 External visual inspection
7 Internal visual inspection
8 Supplementary tests
9 Inspection of cylinder neck/shoulder
10 Pressure test or ultrasonic test
11 Inspection of valve
12 Final operations
13 Rejection and rendering cylinder unserviceable
Annex A (informative) Gas cylinders manufactured
        according to National Regulations
Annex B (normative) Inspection periods
Annex C (normative) Description, evaluation of defects
        and conditions for rejection of seamless
        aluminium alloy gas cylinders at time of
        visual inspection
Annex D (normative) Procedure to be adopted when a
        cylinder valve is suspected to be obstructed
Annex E (normative) Cleaning of aluminium alloy gas
        cylinders
Annex F (normative) Proof pressure test of gas cylinders
Annex G (normative) Volumetric expansion testing of gas
        cylinders
Annex H (normative) Ultrasonic test
Annex I (informative) Inspection and maintenance of
        valves and their connections: recommended
        procedures
Bibliography

Gives the requirements for periodic inspection and testing of seamless aluminium alloy transportable gas cylinders (single or those from bundles) intended for compressed and liquefied gases under pressure, of water capacity from 0,5 L up to 150 L.

DocumentType
Standard
Pages
50
PublisherName
National Standards Authority of Ireland
Status
Withdrawn
SupersededBy

Standards Relationship
SN EN 1802 : 2002 Identical
UNI EN 1802 : 2004 Identical
NEN EN 1802 : 2002 Identical
BS EN 1802:2002 Identical
EN 1802:2002 Identical
NBN EN 1802 : 2002 Identical
NS EN 1802 : 1ED 2002 Identical
UNE-EN 1802:2002 Identical
NF EN 1802 : 2002 Identical
DIN EN 1802:2002-09 Identical

I.S. 291:2015 SELECTION, COMMISSIONING, INSTALLATION, INSPECTION AND MAINTENANCE OF PORTABLE FIRE EXTINGUISHERS

EN 1975:1999/A1:2003 TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS ALUMINIUM AND ALUMINIUM ALLOY GAS CYLINDERS OF CAPACITY FROM 0.5 LITRE UP TO 150 LITRE
EN 629-2 : 1996 TRANSPORTABLE GAS CYLINDERS - 25E TAPER THREAD FOR CONNECTION OF VALVES TO GAS CYLINDERS - GAUGE INSPECTION
ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
PREN 14189 : DRAFT 2001 TRANSPORTABLE GAS CYLINDERS - INSPECTION AND MAINTENANCE OF CYLINDER VALVES AT TIME OF PERIODIC INSPECTION OF GAS CYLINDERS
EN 1089-1 : 1996 TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - STAMPMARKING
PREN 1964-2 : DRAFT 1998 TRANSPORTABLE GAS CYLINDERS - SPECIFICATION FOR THE DESIGN AND CONSTRUCTION OF REFILLABLE TRANSPORTABLE SEAMLESS STEEL GAS CYLINDERS FROM 0.5 LITRE UP TO AND INCLUDING 150 LITRES - TENSILE STRENGTH
ISO 9303:1989 Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections
ISO 13341:2010 Gas cylinders — Fitting of valves to gas cylinders
EN ISO 11114-1:2012/A1:2017 GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1: 2012/AMD 1:2017)
EN 473:2008 Non-destructive testing - Qualification and certification of NDT personnel - General principles
EN 1795 : 1997 TRANSPORTABLE GAS CYLINDERS (EXCLUDING LPG) - PROCEDURES FOR CHANGE OF GAS SERVICE
ISO 10543:1993 Seamless and hot-stretch-reduced welded steel tubes for pressure purposes Full peripheral ultrasonic thickness testing
ISO 11114-2:2013 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
EN ISO 13341:2010/A1:2015 Gas cylinders - Fitting of valves to gas cylinders - Amendment 1 (ISO 13341:2010/Amd 1:2015)
EN 583-1:1998/A1:2003 NON-DESTRUCTIVE TESTING - ULTRASONIC EXAMINATION - GENERAL PRINCIPLES
ISO 6506:1981 Metallic materials — Hardness test — Brinell test
EN ISO 11114-2:2013 Gas cylinders - Compatibility of cylinder and valve materials with gas contents - Part 2: Non-metallic materials (ISO 11114-2:2013)
EN 1089-3:2011 Transportable gas cylinders - Gas cylinder identification (excluding LPG) - Part 3: Colour coding
EN 849:1996/A2:2001 TRANSPORTABLE GAS CYLINDERS - CYLINDER VALVES - SPECIFICATION AND TYPE TESTING
ISO 9764:1989 Electric resistance and induction welded steel tubes for pressure purposes Ultrasonic testing of the weld seam for the detection of longitudinal imperfections
EN 837-1:1996/AC:1998 PRESSURE GAUGES - BOURDON TUBE PRESSURE GAUGES - DIMENSIONS, METROLOGY, REQUIREMENTS AND TESTING
EN 1089-2 : 2002 TRANSPORTABLE GAS CYLINDERS - GAS CYLINDER IDENTIFICATION (EXCLUDING LPG) - PART 2: PRECAUTIONARY LABELS
EN 837-3:1996 Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing
ISO 9305:1989 Seamless steel tubes for pressure purposes Full peripheral ultrasonic testing for the detection of transverse imperfections

View more information
US$87.70
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.