• There are no items in your cart

I.S. EN ISO 1179-2:2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 228-1 THREADS WITH ELASTOMERIC OR METAL-TO-METAL SEALING - PART 2: HEAVY-DUTY (S SERIES) AND LIGHT-DUTY (L SERIES) STUD ENDS WITH ELASTOMERIC SEALING (TYPE E) (ISO 1179-2:2013)
Available format(s)

Hardcopy , PDF

Superseded date

06-15-2023

Language(s)

English

Published date

01-01-2013

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Dimensions
5 Requirements
6 Elastomeric seals
7 Test methods
8 Designation of stud ends
9 Identification statement (reference to this part of ISO 1179)
Annex A (normative) - Test data form for ISO 1179-1 port and
                      ISO 1179-2 stud ends
Bibliography

Describes dimensions, performance requirements and test procedures for heavy-duty (S series) and light-duty (L series) stud ends with ISO 228-1 threads and the elastomeric sealing (type E) that is used with them.

DocumentType
Standard
Pages
25
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ISO 1179-2:2013 Identical
EN ISO 1179-2:2013 Identical

ISO 11926-2:1995 Connections for general use and fluid power Ports and stud ends with ISO 725 threads and O-ring sealing Part 2: Heavy-duty (S series) stud ends
ISO 8434-1:2007 Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors
ISO 5598:2008 Fluid power systems and components Vocabulary
ISO 1101:2017 Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out
ISO 9974-1:1996 Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports
ISO 9974-3:1996 Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B)
ISO 9974-2:1996 Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 2: Stud ends with elastomeric sealing (type E)
ISO 8434-2:2007 Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors
ISO 6149-3:2006 Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends
ISO 7-1:1994 Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation
ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
ISO 19879:2010 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
ISO 6149-2:2006 Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 2: Dimensions, design, test methods and requirements for heavy-duty (S series) stud ends
ISO 286-1:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 1: Basis of tolerances, deviations and fits
ISO 6149-1:2006 Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal
ISO 8434-4:1995 Metallic tube connections for fluid power and general use Part 4: 24 degree cone connectors with O-ring weld-on nipples
ISO 286-2:2010 Geometrical product specifications (GPS) ISO code system for tolerances on linear sizes Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts
ISO 11926-3:1995 Connections for general use and fluid power Ports and stud ends with ISO 725 threads and O-ring sealing Part 3: Light-duty (L series) stud ends
ISO 16030:2001 Pneumatic fluid power — Connections — Ports and stud ends
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
ISO 11926-1:1995 Connections for general use and fluid power Ports and stud ends with ISO 725 threads and O-ring sealing Part 1: Ports with O-ring seal in truncated housing

View more information
US$36.18
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.