• There are no items in your cart

I.S. EN ISO 6892-1:2016

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

View Superseded by
withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT ROOM TEMPERATURE (ISO 6892-1:2016)
Available format(s)

Hardcopy , PDF

Withdrawn date

06-30-2020

Language(s)

English

Published date

01-01-2016

Preview

For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.

Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

National Foreword
European Foreword
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Principle
6 Test pieces
7 Determination of original cross-sectional area
8 Original gauge length and extensometer gauge
   length
9 Accuracy of testing apparatus
10 Conditions of testing
11 Determination of the upper yield strength
12 Determination of the lower yield strength
13 Determination of proof strength, plastic extension
14 Determination of proof strength, total extension
15 Method of verification of permanent set strength
16 Determination of the percentage yield point extension
17 Determination of the percentage plastic extension at
   maximum force
18 Determination of the percentage total extension at
   maximum force
19 Determination of the percentage total extension at
   fracture
20 Determination of percentage elongation after fracture
21 Determination of percentage reduction of area
22 Test report
23 Measurement uncertainty
Annex A (informative) - Recommendations concerning the
        use of computer-controlled tensile testing machines
Annex B (normative) - Types of test pieces to be used for
        thin products: sheets, strips and flats between
        0,1 mm and 3 mm thick
Annex C (normative) - Types of test pieces to be used for
        wire, bars and sections with a diameter
        or thickness of less than 4 mm
Annex D (normative) - Types of test pieces to be used for
        sheets and flats of thickness equal to or
        greater than 3 mm, and wire, bars
        and sections of diameter or thickness
        equal to or greater than 4 mm
Annex E (normative) - Types of test pieces to be used
        for tubes
Annex F (informative) - Estimation of the crosshead
        separation rate in consideration of the stiffness
        (or compliance) of the testing equipment
Annex G (normative) - Determination of the modulus of
        elasticity of metallic materials using a
        uniaxial tensile test
Annex H (informative) - Measuring the percentage
        elongation after fracture if the specified value
        is less than 5%
Annex I (informative) - Measurement of percentage
        elongation after fracture based on subdivision
        of the original gauge length
Annex J (informative) - Determination of the percentage
        plastic elongation without necking, A[wn], for
        long products such as bars, wire, and rods
Annex K (informative) - Estimation of the uncertainty of
        measurement
Annex L (informative) - Precision of tensile testing
        - Results from interlaboratory programmes
Bibliography

Describes the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.

DevelopmentNote
Supersedes I.S. EN 10002-1. (09/2009)
DocumentType
Standard
Pages
96
PublisherName
National Standards Authority of Ireland
Status
Withdrawn
SupersededBy
Supersedes

Standards Relationship
EN ISO 6892-1:2016 Identical
ISO 6892-1:2016 Identical

I.S. 328:2015/AC1:2015 GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4)
I.S. 328:2015 GAS TRANSMISSION PIPELINES AND PIPELINE INSTALLATIONS (EDITION 4)

SEP 1235 : 2012 BESTIMMUNG DES ELASTIZITAETSMODULS AN STAHL IM ZUGVERSUCH BEI RAUMTEMPERATUR
ISO/TTA 2:1997 Tensile tests for discontinuously reinforced metal matrix composites at ambient temperatures
ISO 2566-2:1984 Steel Conversion of elongation values Part 2: Austenitic steels
ISO 3183:2012 Petroleum and natural gas industries Steel pipe for pipeline transportation systems
ISO 9513:2012 Metallic materials — Calibration of extensometer systems used in uniaxial testing
ASTM E 8M : 2004 Standard Test Methods for Tension Testing of Metallic Materials [Metric] (Withdrawn 2008)
ISO/TR 25679:2005 Mechanical testing of metals Symbols and definitions in published standards
ISO 2566-1:1984 Steel Conversion of elongation values Part 1: Carbon and low alloy steels
ISO 80000-1:2009 Quantities and units — Part 1: General
ASTM E 111 : 2017 : REDLINE Standard Test Method for Young’s Modulus, Tangent Modulus, and Chord Modulus
ISO 7500-1:2015 Metallic materials Calibration and verification of static uniaxial testing machines Part 1: Tension/compression testing machines Calibration and verification of the force-measuring system
ISO 377:2017 Steel and steel products — Location and preparation of samples and test pieces for mechanical testing
EN 10291 : 2000 METALLIC MATERIALS - UNIAXIAL CREEP TESTING IN TENSION - METHOD OF TEST
ISO 11960:2014 Petroleum and natural gas industries Steel pipes for use as casing or tubing for wells
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)

View more information
US$124.97
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.