• There are no items in your cart

IEC 61800-2:2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Adjustable speed electrical power drive systems - Part 2: General requirements - Rating specifications for low voltage adjustable speed a.c. power drive systems
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

12-31-2021

Language(s)

English - French

Published date

07-22-2015

FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Ratings and specifications for the act of installing,
  commissioning and operation
5 Test
6 Information and marking requirements
Annex A (informative) - Classification of PDS into low-voltage
        system and high-voltage system
Annex B (informative) - Determination of the input current of
        BDM/CDM/PDS
Bibliography

IEC 61800-2:2015 applies to adjustable speed electric a.c. power drive systems, which include semiconductor power conversion and the means for their control, protection, monitoring, measurement and the a.c. motors. It applies to adjustable speed electric power drive systems intended to feed a.c. motors from a BDM connected to line-to-line voltages up to and including 1 kV a.c. 50 Hz or 60 Hz and/or voltages up to and including 1,5 kV d.c. input side.
NOTE 1 Adjustable speed electric a.c. power drive systems intended to feed a.c. motors, and with rated converter input voltages above 1 000 V a.c. are covered by IEC 61800-4.
NOTE 2 Adjustable speed electric d.c. power drive systems intended to feed d.c. motors are covered by IEC 61800-1.
NOTE 3 For adjustable speed electric a.c. power drive systems having series-connected electronic power converter sections, the line-to-line voltage is the sum of the series connected input voltages.
Traction applications and electric vehicles are excluded from the scope of this standard. IEC 61800-2:2015 is intended to define the following aspects of an a.c. power drive system (PDS):
- principal parts of the PDS;
- ratings and performance;
- specifications for the environment in which the PDS is intended to be installed and operated;
- other specifications which might be applicable when specifying a complete PDS.
This standard provides minimum requirements, which may be used for the development of a specification between customer and manufacturer. This edition includes the following significant technical changes with respect to the previous edition.
a) Clause 1 (Scope) has been updated,
b) Clause 2 (Normative references) has been updated,
c) Clause 3 (Definitions) has been updated including fundamental definitions to be used across the IEC 61800 series of standards,
d) Clause 4 has been updated with respect to:
1) description of the basic topology for BDM/CDM/PDS (4.2);
2) ratings and performance (4.3 and 4.4);
3) reference to applicable standards within the IEC 61800 series with respect to EMC (IEC 61800-3), Electrical safety (IEC 61800-5-1), Functional safety (IEC 61800-5-2), Load duty aspects (IEC TR 61800-6), Communication profiles (IEC 61800-7 series) and Power interface voltage (IEC TS 61800-8) to avoid conflicting requirements (4.5, 4.6, 4.7, 4.10, 4.11, 4.12);
4) update of requirement for ECO design (4.8);
5) update of requirement for environmental evaluation (4.9);
6) implementation of requirement for explosive atmosphere (4.13).
e) Clause 5 has been updated with test requirement in order to provide a clear link between design requirement and test requirement.
f) Clause 6 has been updated to harmonize the marking and documentation requirement within the IEC 61800 series.
g) Existing Annexes A to G have been deleted and replaced with new Annexes A to C.

Committee
TC 22/SC 22G
DevelopmentNote
Stability date: 2019. (07/2015)
DocumentType
Standard
Pages
190
PublisherName
International Electrotechnical Committee
Status
Superseded
SupersededBy
Supersedes

02/206929 DC : DRAFT JUN 2002 IEC 60034-25. ED.1 - ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS FOR CONVERTER SUPPLY
DIN EN 1034-21 E : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
CEI 301-3 : 2005 GUIDE FOR THE CHARACTERISATION AND IDENTIFICATION OF VARIABLE SPEED ELECTRICAL DRIVES BY MEANS OF A PLATE
17/30347395 DC : 0 BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTOR
15/30324519 DC : 0 BS EN ISO 14224 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT
PD IEC/TS 60034-2-3:2013 Rotating electrical machines Specific test methods for determining losses and efficiency of converter-fed AC induction motors
I.S. EN 61800-3:2005 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004 (EQV))
12/30243084 DC : 0 BS EN 1034-21 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
EN 61800-9-2:2017 Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters
CEI CLC/TR 61800-6 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 6: GUIDE FOR DETERMINATION OF TYPES OF LOAD DUTY AND CORRESPONDING CURRENT RATINGS
IEC TS 60034-2-3:2013 Rotating electrical machines - Part 2-3: Specific test methods for determining losses and efficiency of converter-fed AC induction motors
S.R. CLC/TS 60034-31:2011 ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
VDE 0160-109-2 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
UNI EN 1034-21 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
BS EN 62026-2:2013 Low-voltage switchgear and controlgear. Controller-device interfaces (CDIs) Actuator sensor interface (AS-i)
EN 1034-21:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 21: Coating machines
EN 61800-5-2:2017 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
14/30279327 DC : 0 BS EN 61800-3 AMD2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS
11/30243078 DC : 0 BS EN 1034-16 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
BS EN 61800-5-2:2017 Adjustable speed electrical power drive systems Safety requirements. Functional
00/244020 DC : DRAFT SEP 2000 IEC 61800-3 ED.2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS PRODUCT STANDARD INCLUDING SPECIFIC TEST METHODS
09/30209334 DC : 0 BS EN 60034-2-3 - ROTATING ELECTRICAL MACHINES - PART 2-3: SPECIFIC TEST METHODS FOR DETERMINING LOSSES AND EFFICIENCY OF CONVERTER-FED AC MOTORS
CLC/TR 61800-6:2007 Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings
BS EN 1034-16:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Paper and board making machines
13/30278416 DC : 0 BS EN 61800-5-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
DD CLC/TS 60034-31:2011 Rotating electrical machines Selection of energy-efficient motors including variable speed applications. Application guide
BS EN 61800-3 : 2004 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS
DD IEC TS 60034-31 : DRAFT JULY 2010 ROTATING ELECTRICAL MACHINES - PART 31: SELECTION OF ENERGY-EFFICIENT MOTORS INCLUDING VARIABLE SPEED APPLICATIONS - APPLICATION GUIDE
IEC 61800-5-2 REDLINE : 2ED 2016 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
PREN 50598-1 : DRAFT 2013 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
I.S. EN 1034-16:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
I.S. CLC TS 60034-25:2005 ROTATING ELECTRICAL MACHINES - PART 25: GUIDE FOR THE DESIGN AND PERFORMANCE OF CAGE INDUCTION MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
IEC 62026-2:2008 Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)
CLC/TS 60034-31:2011 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
UTEC 53 240-6 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 6: GUIDE FOR DETERMINATION OF TYPES OF LOAD DUTY AND CORRESPONDING CURRENT RATINGS
I.S. EN 61800-5-1:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
IEC TS 60034-25:2014 Rotating electrical machines - Part 25: AC electrical machines used in power drive systems - Application guide
NF EN 62026-2 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I)
17/30370043 DC : 0 BS IEC 62026-2 AMD.1 ED.2.0 - LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I).
I.S. EN ISO 14224:2016 PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COLLECTION AND EXCHANGE OF RELIABILITY AND MAINTENANCE DATA FOR EQUIPMENT (ISO 14224:2016)
EN 61800-5-1:2007/A1:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY (IEC 61800-5-1:2007/A1:2016)
NEMA ICS 7.2 : 2015 APPLICATION GUIDE FOR AC ADJUSTABLE SPEED DRIVE SYSTEMS
15/30314548 DC : 0 BS EN 61800-9-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
I.S. EN 62026-2:2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I) (IEC 62026-2:2008 (MOD))
PD CLC/TR 61800-6:2007 Adjustable speed electrical power drive systems Guide for determination of types of load duty and corresponding current ratings
16/30342855 DC : 0 BS EN 17038-2 - PUMPS - METHODS OF QUALIFICATION AND VERIFICATION OF THE ENERGY EFFICIENCY INDEX FOR ROTODYNAMIC PUMP UNITS - PART 2: TESTING AND CALCULATION OF ENERGY EFFICIENCY INDEX (EEI) OF SINGLE PUMP UNITS
05/30134105 DC : DRAFT MAY 2005 IEC 61800-5-2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
BS EN 1034-21:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Coating machines
13/30280184 DC : 0 BS EN 50598-1 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 1: GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA), AND SEMI ANALYTIC MODEL (SAM)
IEC 61800-3:2017 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods
NF EN 61800-5-2 : 2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
I.S. EN 1034-21:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
IEC TS 60034-18-41:2006 Rotating electrical machines - Part 18-41: Qualification and type tests for Type I electrical insulation systems used in rotating electrical machines fed from voltage converters
UNI EN 1034-16 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
IEC TS 60034-31:2010 Rotating electrical machines - Part 31: Selection of energy-efficient motors including variable speed applications - Application guide
IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
BS EN 61800-5-1:2007 Adjustable speed electrical power drive systems Safety requirements. Electrical, thermal and energy
ISO 14224:2016 Petroleum, petrochemical and natural gas industries Collection and exchange of reliability and maintenance data for equipment
CEI EN 62026-2 : 2013 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (CDIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I)
DIN EN 1034-16:2012-06 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 16: PAPER AND BOARD MAKING MACHINES
BS EN 61800-9-2:2017 Adjustable speed electrical power drive systems Ecodesign for power drive systems, motor starters, power electronics and their driven applications. Energy efficiency indicators for power drive systems and motor starters
13/30280187 DC : 0 BS EN 50598-2 - ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
S.R. CLC/TS 60034-25:2008 ROTATING ELECTRICAL MACHINES - PART 25: GUIDANCE FOR THE DESIGN AND PERFORMANCE OF A.C. MOTORS SPECIFICALLY DESIGNED FOR CONVERTER SUPPLY
PREN 17038-3 : DRAFT 2017 PUMPS - ROTODYNAMIC PUMPS - ENERGY EFFICIENCY INDEX - METHODS OF QUALIFICATION AND VERIFICATION - PART 3: TESTING AND CALCULATION OF ENERGY EFFICIENCY INDEX (EEI) OF BOOSTER SETS
01/205428 DC : DRAFT JUL 2001 IEC 61800-6 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 6: GUIDE FOR DETERMINATION OF TYPES OF LOAD DUTY AND CORRESPONDING CURRENT RATINGS
CEI EN 61800-5-2 : 2009 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
PREN 50598-2 : DRAFT 2013 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
17/30367208 DC : 0 BS EN 17038-3 - PUMPS - ROTODYNAMIC PUMPS - ENERGY EFFICIENCY INDEX - METHODS OF QUALIFICATION AND VERIFICATION - PART 3: TESTING AND CALCULATION OF ENERGY EFFICIENCY INDEX (EEI) OF BOOSTER SETS
EN 62026-2:2013 Low-voltage switchgear and controlgear - Controller-device interfaces (CDIs) - Part 2: Actuator sensor interface (AS-i)
IEC 61800-9-2:2017 Adjustable speed electrical power drive systems - Part 9-2: Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Energy efficiency indicators for power drive systems and motor starters
IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
IEC 61800-5-2:2016 RLV Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
DD IEC/TS 61800-8:2010 Adjustable speed electrical power drive systems Specification of voltage on the power interface
DIN EN 61800-9-2 : 2018-01 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS (IEC 61800-9-2:2017)
DIN EN 1034-21:2012-11 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 21: COATING MACHINES
BS EN 50598-2 : 2014 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
15/30314544 DC : 0 BS EN 61800-9-1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-1: ENERGY EFFICIENCY OF POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - GENERAL REQUIREMENTS FOR SETTING ENERGY EFFICIENCY STANDARDS FOR POWER DRIVEN EQUIPMENT USING THE EXTENDED PRODUCT APPROACH (EPA) AND SEMI ANALYTIC MODEL (SAM)
CEI 301-1 : 1997 ELECTRIC DRIVES - DICTIONARY
BS EN 61800-4:2003 Adjustable speed electrical power drive systems General requirements. Rating specifications for a.c. power drive systems above 1000 V a.c. and not exceeding 35 kV
05/30139105 DC : DRAFT SEP 2005 IEC 61800-5-1 ED 2 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
UNE-EN 50598-2:2015 Ecodesign for power drive systems, motor starters, power electronics & their driven applications - Part 2: Energy efficiency indicators for power drive systems and motor starters
08/30180328 DC : DRAFT MAR 2008 BS EN 61800-8 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 8: SPECIFICATION OF VOLTAGE ON THE POWER INTERFACE
I.S. EN 61800-9-2:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 9-2: ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS AND THEIR DRIVEN APPLICATIONS - ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
IEC TR 61800-6:2003 Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings
I.S. CLC/TR 61800-6:2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 6: GUIDE FOR DETERMINATION OF TYPES OF LOAD DUTY AND CORRESPONDING CURRENT RATINGS
I.S. EN 50598-2:2014 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
NF EN 61800 5-1 : 2007 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
CEI EN 61800-4 : 2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A/C/ POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
I.S. EN 61800-5-2:2017 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-2: SAFETY REQUIREMENTS - FUNCTIONAL
I.S. EN 61800-4:2003 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 4: GENERAL REQUIREMENTS - RATING SPECIFICATIONS FOR A.C. POWER DRIVE SYSTEMS ABOVE 1000 V A.C. AND NOT EXCEEDING 35 KV
EN 61800-3 : 2004 AMD 1 2012 ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 3: EMC REQUIREMENTS AND SPECIFIC TEST METHODS (IEC 61800-3:2004/A1:2011)
06/30148719 DC : DRAFT APR 2006 IEC 62026-2 ED.2 - LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - CONTROLLER-DEVICE INTERFACES (C DIS) - PART 2: ACTUATOR SENSOR INTERFACE (AS-I)
BS EN ISO 14224:2016 Petroleum, petrochemical and natural gas industries. Collection and exchange of reliability and maintenance data for equipment
15/30322229 DC : 0 BS EN 61800-5-1:2007/AMD 1 - ADJUSTABLE SPEED ELECTRICAL POWER DRIVE SYSTEMS - PART 5-1: SAFETY REQUIREMENTS - ELECTRICAL, THERMAL AND ENERGY
EN 1034-16:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 16: Paper and board making machines
EN 61800-4:2003 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
EN 50598-2:2014/A1:2016 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
CLC/TS 60034-25:2008 Rotating electrical machines - Part 25: Guidance for the design and performance of a.c. motors specifically designed for converter supply

IEC 61800-3:2017 Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods
IEC 60038:2009 IEC standard voltages
IEC 61800-4:2002 Adjustable speed electrical power drive systems - Part 4: General requirements - Rating specifications for a.c. power drive systems above 1 000 V a.c. and not exceeding 35 kV
IEC 61158-2:2014 Industrial communication networks - Fieldbus specifications - Part 2: Physical layer specification and service definition
IEC 60068-2-68:1994 Environmental testing - Part 2-68: Tests - Test L: Dust and sand
IEC 60034-9:2003+AMD1:2007 CSV Rotating electrical machines - Part 9: Noise limits
IEC 60068-2-27:2008 Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
IEC TS 62578:2015 Power electronics systems and equipment - Operation conditions and characteristics of active infeed converter (AIC) applications including design recommendations for their emission values below 150 kHz
IEC 61800-7-1:2015 Adjustable speed electrical power drive systems - Part 7-1: Generic interface and use of profiles for power drive systems - Interface definition
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
EN 50325-4:2002 Industrial communications subsystem based on ISO 11898 (CAN) for controller-device interfaces - Part 4: CANopen
IEC TS 61800-8:2010 Adjustable speed electrical power drive systems - Part 8: Specification of voltage on the power interface
IEC 60721-2-6:1990 Classification of environmental conditions. Part 2: Environmental conditions appearing in nature. Earthquake vibration and shock
IEC 60146-1-1:2009 Semiconductor converters - General requirements and line commutated converters - Part 1-1: Specification of basic requirements
IEC TR 60146-1-2:2011 Semiconductor converters - General requirements and line commutated converters - Part 1-2: Application guide
IEC 60027-3:2002 Letter symbols to be used in electrical technology - Part 3: Logarithmic and related quantities, and their units
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
IEC 60721-3-2:1997 Classification of environmental conditions - Part 3: Classification of groups of environmental parameters and their severities - Section 2: Transportation
IEC 60068-2-2:2007 Environmental testing - Part 2-2: Tests - Test B: Dry heat
EN 50598-2:2014/A1:2016 ECODESIGN FOR POWER DRIVE SYSTEMS, MOTOR STARTERS, POWER ELECTRONICS & THEIR DRIVEN APPLICATIONS - PART 2: ENERGY EFFICIENCY INDICATORS FOR POWER DRIVE SYSTEMS AND MOTOR STARTERS
EN 50598-3:2015 Ecodesign for power drive systems, motor starters, power electronics and their driven applications - Part 3: Quantitative eco design approach through life cycle assessment including product category rules and the content of environmental declarations
IEC 60034-1:2017 Rotating electrical machines - Part 1: Rating and performance
IEC 61378-3:2015 Converter transformers - Part 3: Application guide
CSA C838 : 2013 ENERGY EFFICIENCY TEST METHODS FOR THREE-PHASE VARIABLE FREQUENCY DRIVE SYSTEMS
IEC 60721-3-3:1994+AMD1:1995+AMD2:1996 CSV Classification of environmental conditions - Part 3-3: Classification of groups of environmental parameters and their severities - Stationary use at weatherprotected locations
IEC 61131-2:2017 Industrial-process measurement and control - Programmable controllers - Part 2: Equipment requirements and tests
IEC 61439-1:2011 Low-voltage switchgear and controlgear assemblies - Part 1: General rules
IEC TR 61800-6:2003 Adjustable speed electrical power drive systems - Part 6: Guide for determination of types of load duty and corresponding current ratings
EN 50495:2010 Safety devices required for the safe functioning of equipment with respect to explosion risks
IEC 60664-1:2007 Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 60068-2-52:2017 Environmental testing - Part 2-52: Tests - Test Kb: Salt mist, cyclic (sodium chloride solution)
IEC 61378-1:2011 Converter transformers - Part 1: Transformers for industrial applications
IEC 61800-5-2:2016 Adjustable speed electrical power drive systems - Part 5-2: Safety requirements - Functional
IEC 61800-1:1997 Adjustable speed electrical power drive systems - Part 1: General requirments - Rating specifications for low voltage adjustables speed d.c. power drive systems
IEC 60721-3-1:1997 Classification of environmental conditions - Part 3 Classification of groups of environmental parameters and their severities - Section 1: Storage

View more information
US$435.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.