INCITS/ISO/IEC 11319 : 1993

Section 1 : General
1 Scope
2 Conformance
3 Normative references
4 Definitions
   4.1 AC erase
   4.2 Average Signal Amplitude
   4.3 azimuth
   4.4 back surface
   4.5 bit cell
   4.6 byte
   4.7 cartridge
   4.8 Cyclic Redundancy Check (CRC) Character
   4.9 Error Correcting Code (ECC)
   4.10 flux transition position
   4.11 flux transition spacing
   4.12 magnetic tape
   4.13 Master Standard Reference Tape
   4.14 Physical Beginning of Tape (PBOT)
   4.15 Physical End of Tape (PEOT)
   4.16 physical recording density
   4.17 Secondary Reference Amplitude
   4.18 Secondary Reference Field
   4.19 Secondary Standard Reference Tape
   4.20 Standard Reference Current (Ir)
   4.21 Tape Reference Edge
   4.22 Test Recording Current
   4.23 tone
   4.24 track
   4.25 Typical Field
5 Environment and safety
   5.1 Testing environment
   5.2 Operating environment
   5.3 Storage environment
   5.4 Transportation
   5.5 Safety
   5.6 Flammability
Section 2 : Requirements for the case
6 Dimensional and mechanical characteristics of the case
   6.1 General
   6.2 Overall dimension (figure 3)
   6.3 Holding areas
   6.4 Cartridge insertion
   6.5 Window (figure 1)
   6.6 Loading grips (figure 3)
   6.7 Label areas (figure 3)
   6.8 Datum areas and datum holes (figures 4, 5 and 6)
   6.9 Support areas
   6.10 Recognition holes (figures 5, 6 and 7)
   6.11 Write-inhibit Hole (figures 6 and 7)
   6.12 Pre-positioning surfaces (figures 3 and 5)
   6.13 Cartridge lid (figures 3 and 8)
   6.14 Cartridge reel lock (figure 11)
   6.15 Reel access holes (figure 5)
   6.16 Interface between the reels and the drive
        spindles (figures 17 and 18)
   6.17 Light path (figures 5, 7, 15 and 16)
   6.18 Position of the tape in the case (figure 16)
   6.19 Tape path zone (figures 16 and 17)
   6.20 Tape access cavity (figure 5)
   6.21 Tape access cavity clearance requirements (figure 19)
Section 3 : Requirements for the unrecorded tape
7 Mechanical, physical and dimensional characteristics of
   the tape
   7.1 Materials
   7.2 Tape length
   7.3 Width
   7.4 Discontinuities
   7.5 Thickness
   7.6 Longitudinal curvature
   7.7 Cupping
   7.8 Coating adhesion (figure 20)
   7.9 Layer-to-layer adhesion
   7.10 Tensile strength
   7.11 Residual elongation
   7.12 Electrical resistance of the surface
   7.13 Tape winding
   7.14 Light transmittance of tape
8 Magnetic recording performance
   8.1 Test conditions
   8.2 Typical Field
   8.3 Signal Amplitude
   8.4 Resolution
   8.5 Narrow-band signal-to-noise ratio
   8.6 Ease of erasure
   8.7 Tape quality
   8.8 Inhibitor tape
Section 4 : Requirements for an interchanged tape
9 Format
   9.1 General
   9.2 Information matrix
10 Method of recording
   10.1 Physical recording density
   10.2 Bit shift
   10.3 Read signal amplitudes
   10.4 Erasure
11 Track geometry
   11.1 Track positions
   11.2 Track pitch
   11.3 Track width
   11.4 Track angle
   11.5 Linearity of track edges
   11.6 Azimuth
12 Format of an information track
   12.1 Channel bit
   12.2 Information Segment
   12.3 Information Block
   12.4 Information Zone
   12.5 Servo Zone
   12.6 Information Tracks
13 Tape Mark
   13.1 Description
   13.2 Long Tape Mark
   13.3 Short Tape Mark
14 ID Information
   14.1 Column 00, Row 00
   14.2 Column 00, Row 01
   14.3 Column 00, Row 02
   14.4 Column 00, Row 03
   14.5 Column 00, Row 04
   14.6 Column 00, Rows 05, 06
   14.7 Column 00, Row 07
   14.8 Column 00, Rows 08, 09, 10
   14.9 Column 00, Rows 11, 12, 13
15 Rewritten Information Blocks
16 Physical tape format
   16.1 Initial Erased Area
   16.2 Logical Beginning of Tape Area (LBOT Area)
   16.3 Usable area of the tape
   16.4 Post Data erased area
Annexes
A Measurement of light transmittance of tape and leaders
B Measurement of bit shift
C Representation of 8-bit bytes by 10-bit patterns
D Recommendations for transportation
E Inhibitor tape