|
IEC 60243-1 : 3.0
|
ELECTRIC STRENGTH OF INSULATING MATERIALS - TEST METHODS - PART 1: TESTS AT POWER FREQUENCIES |
|
IEC 60112 : 4.1
|
METHOD FOR THE DETERMINATION OF THE PROOF AND THE COMPARATIVE TRACKING INDICES OF SOLID INSULATING MATERIALS |
|
ISO 22007-3 : 2008(R2016)
|
PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 3: TEMPERATURE WAVE ANALYSIS METHOD |
|
ISO 3167 : 2014
|
PLASTICS - MULTIPURPOSE TEST SPECIMENS |
|
ISO 22007-4 : 2017
|
PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 4: LASER FLASH METHOD |
|
ISO 974 : 2000(R2015)
|
PLASTICS - DETERMINATION OF THE BRITTLENESS TEMPERATURE BY IMPACT |
|
IEC 60250 : 1.0
|
RECOMMENDED METHODS FOR THE DETERMINATION OF THE PERMITTIVITY AND DIELECTRIC DISSIPATION FACTOR OF ELECTRICAL INSULATING MATERIALS AT POWER, AUDIO AND RADIO FREQUENCIES INCLUDING METRE WAVELENGTHS |
|
ISO 815-1 : 2014
|
RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF COMPRESSION SET - PART 1: AT AMBIENT OR ELEVATED TEMPERATURES |
|
ISO 10350-1 : 2017
|
PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS |
|
ISO 8256 : 2004(R2017)
|
PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH |
|
ISO 11359-2 : 1999(R2015)
|
PLASTICS - THERMOMECHANICAL ANALYSIS (TMA) - PART 2 - DETERMINATION OF COEFFICIENT OF LINEAR THERMAL EXPANSION AND GLASS TRANSITION TEMPERATURE |
|
ISO 34-1 : 2015
|
RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF TEAR STRENGTH - PART 1: TROUSER, ANGLE AND CRESCENT TEST PIECES |
|
ASTM E 96 : 2014
|
TEST METHODS FOR WATER VAPOR TRANSMISSION OF MATERIALS |
|
ISO 75-2 : 2013(R2018)
|
PLASTICS - DETERMINATION OF TEMPERATURE OF DEFLECTION UNDER LOAD - PART 2: PLASTICS AND EBONITE |
|
ISO/DIS 16365-2 : 60.00 (2014)
|
PLASTICS - THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES |
|
ISO 527-2 : 2012(R2017)
|
PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 2: TEST CONDITIONS FOR MOULDING AND EXTRUSION PLASTICS |
|
ISO 11357-3 : 2011
|
PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 3: DETERMINATION OF TEMPERATURE AND ENTHALPY OF MELTING AND CRYSTALLIZATION |
|
ISO 11357-4 : 2014
|
PLASTICS - DIFFERENTIAL SCANNING CALORIMETRY (DSC) - PART 4: DETERMINATION OF SPECIFIC HEAT CAPACITY |
|
ISO 294-4 : 2001(R2010)
|
PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 4: DETERMINATION OF MOULDING SHRINKAGE |
|
IEC 60093 : 2.0
|
METHODS OF TEST FOR VOLUME RESISTIVITY AND SURFACE RESISTIVITY OF SOLID ELECTRICAL INSULATING MATERIALS |
|
IEC 60695-11-10 : 2.0
|
FIRE HAZARD TESTING - PART 11-10: TEST FLAMES - 50 W HORIZONTAL AND VERTICAL FLAME TEST METHODS |
|
ISO 1183-1 : 2012
|
PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 1: IMMERSION METHOD, LIQUID PYKNOMETER METHOD AND TITRATION METHOD |
|
ISO 1183-2 : 2004(R2012)
|
PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD |
|
ISO 1183-3 : 1999(R2016)
|
PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 3: GAS PYKNOMETER METHOD |
|
ISO 14910-1 : 2013
|
PLASTICS - THERMOPLASTIC POLYESTER/ESTER AND POLYETHER/ESTER ELASTOMERS FOR MOULDING AND EXTRUSION - PART 1: DESIGNATION SYSTEM AND BASIS FOR SPECIFICATIONS |
|
ISO 179-1 : 2010(R2015)
|
PLASTICS - DETERMINATION OF CHARPY IMPACT PROPERTIES - PART 1: NON-INSTRUMENTED IMPACT TEST |
|
ISO 15512 : 2016
|
PLASTICS - DETERMINATION OF WATER CONTENT |
|
ISO 62 : 2008(R2016)
|
PLASTICS - DETERMINATION OF WATER ABSORPTION |
|
ISO 306 : 2013
|
PLASTICS - THERMOPLASTIC MATERIALS - DETERMINATION OF VICAT SOFTENING TEMPERATURE (VST) |
|
ISO 294-1 : 2017
|
PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS |
|
ISO 37 : 2017
|
RUBBER, VULCANIZED OR THERMOPLASTIC - DETERMINATION OF TENSILE STRESS-STRAIN PROPERTIES |
|
ISO 4589-2 : 2017
|
PLASTICS - DETERMINATION OF BURNING BEHAVIOUR BY OXYGEN INDEX - PART 2: AMBIENT-TEMPERATURE TEST |
|
ISO 22007-2 : 2015
|
PLASTICS - DETERMINATION OF THERMAL CONDUCTIVITY AND THERMAL DIFFUSIVITY - PART 2: TRANSIENT PLANE HEAT SOURCE (HOT DISC) METHOD |
|
ISO 1133-2 : 2011(R2016)
|
PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND MELT VOLUME-FLOW RATE (MVR) OF THERMOPLASTICS - PART 2: METHOD FOR MATERIALS SENSITIVE TO TIME-TEMPERATURE HISTORY AND/OR MOISTURE |
|
ISO 899-1 : 2017
|
PLASTICS - DETERMINATION OF CREEP BEHAVIOUR - PART 1: TENSILE CREEP |
|
ISO 178 : 2010(R2015)
|
PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES |
|
ISO 868 : 2003(R2018)
|
PLASTICS AND EBONITE - DETERMINATION OF INDENTATION HARDNESS BY MEANS OF A DUROMETER (SHORE HARDNESS) |