ISO 17484-1:2014
Current
Current
The latest, up-to-date edition.
Plastics piping systems Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) Part 1: Specifications for systems
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Language(s)
English
Published date
05-23-2014
ISO 17484-1:2014 specifies the general requirements and the performance requirements for multilayer pipe systems based on pipes, fittings and their joints intended to be used for gas supply within buildings.
PE-X and PE pipes composed of one stress-designed layer, adhesive and a barrier layer are also covered by ISO 17484-1:2014.
ISO 17484-1:2014 gives guidance for the design of piping systems consisting of multilayer pipes based on thermoplastics, for which at least 60 % of the wall thickness is polymeric material. Polymeric materials intended for stress-designed layers and all inner layers are required to be polyethylene (PE) and/or crosslinked polyethylene (PE-X) in accordance with Annex A of ISO 17484-1:2014.
ISO 17484-1:2014 applies to systems that operate at temperatures of 20 C up to +60 C.
For the purpose of ISO 17484-1:2014, crosslinked polyethylene (PE-X) and adhesive layers are considered as thermoplastic materials.
For sizes greater than 63 mm the requirements of ISO 18225 have to be fulfilled in addition.
ISO 17484-1:2014 is applicable for piping systems used in buildings to supply gas with a maximum operating pressure up to and including 500 kPa (5 bar).
ISO 17484-1:2014 applies to the following fuels:
- Category D gaseous fuel: natural gas;
- Category E gaseous fuel: LPG vapour, and natural gas or LPG vapour.
| DevelopmentNote |
Supersedes ISO/DIS 17484-1. (05/2014)
|
| DocumentType |
Standard
|
| Pages |
33
|
| PublisherName |
International Organization for Standardization
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| SS-ISO 17484-1:2019 | Identical |
| BS ISO 17484-1:2014 | Identical |
| NEN ISO 17484-1 : 2014 | Identical |
| SANS 17484-1 : 1ED 2010 | Identical |
| DIN EN 1254-8:2012-12 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| 12/30256669 DC : 0 | BS ISO 4437-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| 04/30126883 DC : DRAFT DEC 2004 | ISO 4437 - BURIED POLYETHYLENE (PE) PIPES FOR THE SUPPLY OF GASEOUS FUELS - METRIC SERIES - SPECIFICATIONS |
| EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| UNE-EN 1555-2:2011 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| BS EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Pipes |
| I.S. 813:2014+A1:2017 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| BS ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Pipes |
| BS EN 1254-8:2012 | Copper and copper alloys. Plumbing fittings Fittings with press ends for use with plastics and multilayer pipes |
| ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels Metric series Specifications |
| ISO 17484-2:2009 | Plastics piping systems Multilayer pipe systems for indoor gas installations Part 2: Code of pratice |
| DIN EN 1555-2:2010-12 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 2: Pipes |
| I.S. EN 1555-2:2010 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| 08/30153234 DC : DRAFT JAN 2008 | BS ISO 17484-2 - PLASTICS PIPING SYSTEMS - MULTILAYER PIPE SYSTEMS FOR INDOOR GAS INSTALLATIONS - PART 2: CODE OF PRACTICE |
| 11/30213590 DC : 0 | BS EN 1254-8 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| UNI EN 1254-8 : 2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| BS ISO 4437:2007 | Buried polyethylene (PE) pipes for the supply of gaseous fuels. Metric series. Specifications |
| I.S. 813:2014 | DOMESTIC GAS INSTALLATIONS (EDITION 3) AND AMENDMENT 1:2017 |
| UNI EN 1555-2 : 2011 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| UNE-EN 1254-8:2013 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| EN 1254-8:2012 | Copper and copper alloys - Plumbing fittings - Part 8: Fittings with press ends for use with plastics and multilayer pipes |
| UNI/TS 11344 : 2009 | METALLO-PLASTIC MULTILAYER PIPING SYSTEMS AND FITTINGS FOR INDOOR INSTALLATION FOR THE CONVEYANCE OF GASEOUS FUELS |
| I.S. EN 1254-8:2012 | COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 8: FITTINGS WITH PRESS ENDS FOR USE WITH PLASTICS AND MULTILAYER PIPES |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| 08/30191147 DC : 0 | BS EN 1555-2 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 2: PIPES |
| UNE 53008-1:2014 | Plastics piping systems. Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa). Part 1: Specifications for pipes, fittings and the system |
| EN 1555-3:2010+A1:2012 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 3: Fittings |
| ISO 4437-5:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 5: Fitness for purpose of the system |
| EN 1775:2007 | Gas supply - Gas pipework for buildings - Maximum operating pressure less than or equal to 5 bar - Functional recommendations |
| ISO 10146:1997 | Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength |
| ISO 6447:1983 | Rubber seals Joint rings used for gas supply pipes and fittings Specification for material |
| ISO 14531-1:2002 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 1: Pipes |
| ISO 161-1:1996 | Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series |
| DVGW W 542 : 2009 | COMPOUND PIPES IN THE DRINKING WATER INSTALLATION; REQUIREMENTS AND TESTING |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO 17456:2006 | Plastics piping systems Multilayer pipes Determination of long-term strength |
| ISO 3:1973 | Preferred numbers Series of preferred numbers |
| ISO 4437-2:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 2: Pipes |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| EN 10088-2:2014 | STAINLESS STEELS - PART 2: TECHNICAL DELIVERY CONDITIONS FOR SHEET/PLATE AND STRIP OF CORROSION RESISTING STEELS FOR GENERAL PURPOSES |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient |
| ISO 4437-1:2014 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) — Part 1: General |
| ISO 3126:2005 | Plastics piping systems Plastics components Determination of dimensions |
| ISO 7-1:1994 | Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions, tolerances and designation |
| EN 713:1993 | Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending |
| ISO 24033:2009 | Polyethylene of raised temperature resistance (PE-RT) pipes — Effect of time and temperature on the expected strength |
| ISO 14531-3:2010 | Plastics pipes and fittings Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels Metric series Specifications Part 3: Fittings for mechanical jointing (including PE-X/metal transitions) |
| ISO/TR 10837:1991 | Determination of the thermal stability of polyethylene (PE) for use in gas pipes and fittings |
| ISO 10508:2006 | Plastics piping systems for hot and cold water installations Guidance for classification and design |
| ISO 11357-6:2008 | Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 14531-2:2004 | Plastics pipes and fittings — Crosslinked polyethylene (PE-X) pipe systems for the conveyance of gaseous fuels — Metric series — Specifications — Part 2: Fittings for heat-fusion jointing |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 13480:1997 | Polyethylene pipes Resistance to slow crack growth Cone test method |
| ISO 18225:2012 | Plastics piping systems — Multilayer piping systems for outdoor gas installations — Specifications for systems |
| ISO 4437-3:2014 | Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings |
| ISO 10147:2011 | Pipes and fittings made of crosslinked polyethylene (PE-X) Estimation of the degree of crosslinking by determination of the gel content |
| EN 549:1994 | Rubber materials for seals and diaphragms for gas appliances and gas equipment |
| ISO 17454:2006 | Plastics piping systems Multilayer pipes Test method for the adhesion of the different layers using a pulling rig |
| EN 12117:1997 | Plastics piping systems - Fittings, valves and ancillaries - Determination of gaseous flow rate/pressure drop relationships |
| EN 1982:2017 | Copper and copper alloys - Ingots and castings |
| ISO 13951:2015 | Plastics piping systems Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading |
| EN 573-3:2013 | Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products |
| ISO 6957:1988 | Copper alloys Ammonia test for stress corrosion resistance |
| ISO 13623:2017 | Petroleum and natural gas industries — Pipeline transportation systems |
| ISO 3503:2015 | Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending |
US$175.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
Hardcopy - English
PDF - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.