MIL-DTL-32371 Base Document:2012
Current
Current
The latest, up-to-date edition.
Fittings, Adapter, Hydraulic and Pneumatic, Spherical to ORFS Connectors, 1500 to 3000 PSI, General Specification for
Available format(s)
PDF
Published date
04-24-2012
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
Specifies fittings, adapter, hydraulic, pneumatic, and conveyance, spherical to O-ring face seal (ORFS) connectors, 1500 to 3000 psi, -65 degrees F to 250 degrees F temperature range, for use in hydraulic or pneumatic systems.
This specification covers fittings, adapter, hydraulic, pneumatic, and conveyance, spherical to O-ring face seal (ORFS) connectors, 1500 to 3000 psi, -65°F to 250°F temperature range, for use in hydraulic or pneumatic systems. The spherical 37° flared tube-fitting end is physically interchangeable with 37° flared fittings. Spherical connector ends are in accordance with SAE-AS5309 and SAE-AS5310 connector ends, the ORFS end is in accordance with SAE-J1453-3 connector ends.
| DocumentType |
Standard
|
| Pages |
24
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Current
|
| MIL-DTL-32371-8 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, 90 Degree Elbow, Bulkhead |
| MIL-DTL-32371-10 Base Document:2012 | Fittings, Hydraulic Tube, Sleeve, Double Angle |
| MIL-DTL-32371-4 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, Tee, Spherical on Branch |
| MIL-DTL-32371-3 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, 90 Degrees Elbow |
| MIL-DTL-32371-6 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, Nipple Tube, Regular Hex, Long |
| MIL-DTL-32371-9 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, Tee, Bulkhead, Spherical on Run |
| MIL-DTL-32371-1 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, Straight |
| MIL-DTL-32371-5 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, Union Cross, Spherical on Branch |
| MIL-DTL-32371-7 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, 45 Degrees Elbow, Bulkhead |
| MIL-DTL-32371-2 Base Document:2012 | Fittings, Hydraulic Tube, Spherical to ORFS, Male Adapter, 45 Degrees Elbow |
| SAE AMS 2486 : 2010 | CONVERSION COATING OF TITANIUM ALLOYS FLUORIDE-PHOSPHATE TYPE |
| ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
| SAE AS 5309 : 2015 | FITTING END, SPHERICAL, 37 DEGREE FLARED TUBE CONNECTION DESIGN STANDARD |
| SAE AMS 5645 : 2016 | STEEL, CORROSION AND HEAT RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 10NI - 0.40TI (321), SOLUTION HEAT TREATED |
| SAE AMS QQ A 225/9 : 2014 | ALUMINUM ALLOY 7075, BAR, ROD, WIRE, AND SPECIAL SHAPES; ROLLED, DRAWN, OR COLD FINISHED |
| SAE AMS QQ P 416 : 2016 | PLATING, CADMIUM (ELECTRODEPOSITED) |
| MIL-STD-130 Revision N:2007 | IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY |
| SAE J 2658 : 2013 | CARBON AND STEEL ALLOY TUBE CONDUCTOR ASSEMBLIES FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER METALLIC TUBE ASSEMBLIES |
| SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
| MIL-DTL-16232 Revision G:2000 | PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE |
| MIL-PRF-7808 Revision L:1997 | LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE |
| ANSI/NCSL Z540 3 : 2006(R2013) | REQUIREMENTS FOR THE CALIBRATION OF MEASURING AND TEST EQUIPMENT |
| MIL-PRF-5606 Revision H:2002 | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE |
| SAE AMS 6382 : 2014 | STEEL, BARS, FORGINGS, AND RINGS 0.95CR - 0.20MO (0.38 - 0.43C) (SAE 4140) ANNEALED |
| SAE AMS 5643 : 2016 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 16CR - 4.0NI - 0.30CB (NB) - 4.0CU, SOLUTION HEAT TREATED, PRECIPITATION HARDENABLE |
| SAE AS 4395 : 2013 | FITTING END, FLARED, TUBE CONNECTION, DESIGN STANDARD |
| SAE AMS 5743 : 2014 | STEEL, CORROSION AND HEAT-RESISTANT, BARS AND FORGINGS 15.5CR - 4.5NI - 2.9MO - 0.10N SOLUTION HEAT TREATED, SUB-ZERO COOLED, EQUALIZED, AND OVER-TEMPERED |
| ASTM E 384 : 2017 : REDLINE | Standard Test Method for Microindentation Hardness of Materials |
| SAE J 403 : 2014 | CHEMICAL COMPOSITIONS OF SAE CARBON STEELS |
| ASTM B 221 : 2014 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes |
| SAE AMS 5647 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 9.5NI, SOLUTION HEAT TREATED |
| MIL-STD-889 Revision C:2016 | DISSIMILAR METALS |
| MIL-DTL-81706 Revision B:2004 | Chemical Conversion Materials for Coating Aluminum and Aluminum Alloys |
| MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
| SAE AS 5206 : 2015 | NUT, FLARED, LONG |
| SAE AMS 2417 : 2013 | PLATING, ZINC-NICKEL ALLOY |
| SAE AMS R 25988 : 1998 | RUBBER, FLUOROSILICONE ELASTOMER, OIL-AND-FUEL-RESISTANT, SHEETS, STRIPS, MOLDED PARTS AND EXTRUDED SHAPES |
| SAE J 1453/3 : 2012 | SPECIFICATION FOR O-RING FACE SEAL CONNECTORS: PART 3 - REQUIREMENTS, DIMENSIONS, AND TESTS FOR STEEL UNIONS, BULKHEADS, SWIVELS, BRAZE SLEEVES, CAPS, AND CONNECTORS WITH SAE J1926-2 INCH STUD ENDS |
| SAE AMS C 81562 : 1998 | COATINGS, CADMIUM, TIN-CADMIUM AND ZINC (MECHANICALLY DEPOSITED) |
| ASTM B 567 : 1998 | Standard Test Method for Measurement of Coating Thickness by the Beta Backscatter Method |
| SAE J 1453/1 : 2012 | SPECIFICATION FOR O-RING FACE SEAL CONNECTORS - PART 1: TUBE CONNECTION DETAILS AND COMMON REQUIREMENTS FOR PERFORMANCE AND TESTS |
| SAE AS 8879 : 2004 | SCREW THREADS - UNJ PROFILE, INCH CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER |
| SAE AMS 2451/9 : 2012 | PLATING, BRUSH, ZINC-NICKEL, LOW HYDROGEN EMBRITTLEMENT |
| SAE J 514 : 2012 | HYDRAULIC TUBE FITTINGS |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| SAE AS 5310 : 2015 | FITTING END, BULKHEAD, SPHERICAL, 37° FLARED TUBE CONNECTION DESIGN STANDARD |
| SAE AS 2078 : 2015 | TEST METHODS, HOSE ASSEMBLIES, POLYTETRAFLUOROETHYLENE (PTFE) |
| SAE AMS 2700E : 2011 | PASSIVATION OF CORROSION RESISTANT STEELS |
| MIL-PRF-83282 Revision D:1997 | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537 |
| SAE AMS 5639 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 10NI, SOLUTION HEAT TREATED |
| SAE AMS 6370 : 2016 | STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| ASTM B 241/B241M : 2016 : REDLINE | Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube |
| SAE AS 4375 : 2013 | FITTING END, FLARELESS, DESIGN STANDARD |
| MIL-C-15726 Revision F:1988 | COPPER NICKEL ALLOY, SHEET, PLATE, STRIP, BAR, ROD AND WIRE |
| SAE AS 5175 : 2017 | NUT, COUPLING, FLARED |
| SAE AMS 4124 : 2012 | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS, RODS, AND WIRE - 5.6ZN - 2.5MG - 1.6CU - 0.23CR (7075-T7351), SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING, AND OVERAGED |
| SAE AMS 4928 : 2016 | TITANIUM ALLOY BARS, WIRE, FORGINGS, RINGS, AND DRAWN SHAPES, 6AL - 4V, ANNEALED |
US$20.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.