• There are no items in your cart

NBN EN 1088 : 1996 + A2 2008

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF MACHINERY - INTERLOCKING DEVICES ASSOCIATED WITH GUARDS - PRINCIPLES FOR DESIGN AND SELECTION
Superseded date

12-01-2013

Published date

01-12-2013

Foreword
0 Introduction
1 Scope
2 Normative references
3 Definitions
3.1 Interlocking device (interlock)
3.2 Interlocking guard
3.3 Interlocking guard with guard locking
3.4 Guard locking device
3.5 Automatic monitoring
3.6 Positive mode actuation
3.7 Positive opening operation of a contact element
3.8 Stopping time (time for hazard elimination)
3.9 Access time (time for access to a danger zone)
4 Operating principles and typical forms of interlocking
     devices associated with guards
4.1 Interlocking principles
4.2 Typical forms of interlocking devices
4.3 Technological forms of interlocking devices
5 Provisions for the design of interlocking devices
     (independent of the nature of the energy source)
5.1 Actuation modes of mechanically actuated position
     detectors
5.2 Arrangement and fastening of position detectors
5.3 Arrangement and fastening of cams
5.4 Reducing the probability of common cause failures
5.5 Guard locking device
5.6 Delay devices
5.7 Design to minimize defeat possibilities
5.8 Environmental considerations
6 Additional technological requirements for electrical
     interlocking devices
6.1 Compliance with EN 60204-1
6.2 Interlocking devices incorporating mechanically actuated
     position switches
6.3 Interlocking devices incorporating non-mechanically
     actuated position switches (proximity switches and
     magnetic switches)
7 Selection of an interlocking device
7.1 General
7.2 Conditions of use and intended use
7.3 Risk assessment
7.4 Stopping time and access time
7.5 Frequency of access
7.6 Performance considerations
Annexes
A (informative) Guard-operated interlocking device with
     one single cam-operated position detector
B (informative) Guard-operated interlocking device with
     tongue-operated switch
C (informative) Direct (mechanical) interlocking between
     guard and start/stop manual control
D (informative) Captive-key interlocking device
E (informative) Trapped-key interlocking device
F (informative) Plug and socket interlocking device (plug/
     socket combination)
G (informative) Guard-operated interlocking device
     incorporating two cam-operated position detectors
H (informative) Mechanical interlocking between a guard
     and a movable element
J (informative) Electrical interlocking device
     incorporating magnetically actuated (magnetic) switches
K (informative) Electrical interlocking device
     incorporating two proximity detectors
L (informative) Pneumatic/hydraulic interlocking devices
M (informative) Interlocking device with spring applied/
     power released guard locking device
N (informative) Interlocking device with guard locking,
     with manually operated delay device
P (informative) Bibliography

Covers the parts of guards which actuate interlocking devices. Requirements for guards are given in prEN 953. The processing of the signal from the interlocking device to stop and immobilize the machine is dealt with in prEN 954-1.

DevelopmentNote
1996 Edition Re-Issued in November 2008 & incorporates AMD 2 2008. (01/2009)
DocumentType
Standard
PublisherName
Belgian Standards
Status
Superseded

Standards Relationship
EN 1088:1995+A2:2008 Identical
I.S. EN 1088:1996 Identical
DIN EN 1088:1996-02 Identical
DIN EN 1088:2008-10 Identical
UNE-EN 1088:1996 Identical
UNI EN 1088 : 2008 Identical
BS EN 1088 : 1995 Identical

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.