• There are no items in your cart

PREN 1010-1 : DRAFT 2003

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS
Superseded date

12-01-2004

Published date

01-12-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective measures
  5.1 General
  5.2 Requirements common to printing and paper converting
      machines
      5.2.1 Safeguarding of danger points
      5.2.2 Guards and interlocks
      5.2.3 Devices for setting-up, cleaning, trouble-shooting
             during the work process and maintenance
      5.2.4 Explosion prevention and protection
      5.2.5 Electrical equipment
      5.2.6 Control systems
      5.2.7 Indicators, marking, actuators, prestart warning devices
      5.2.8 Two-hand controls
      5.2.9 Electrosensitive protective devices (ESPDs)
      5.2.10 Pressure sensitive mats, trip devices
      5.2.11 Safety position switches
      5.2.12 Work platforms, access stairs, passageways and raised
             workplaces
      5.2.13 Stability
      5.2.14 High contact temperatures
      5.2.15 Noise
      5.2.16 Radiation hazards
      5.2.17 Immunity to electromagnetic disturbances
  5.3 Common devices
      5.3.1 Stationary knives
      5.3.2 Rotary tools
      5.3.3 Dangerous tools
      5.3.4 Feeding units, delivery units (pile lifting and lowering
             devices)
      5.3.5 Reel unwinding and rewinding devices for webs
6 Verification of the safety requirements and/or protective measures
7 Information for use
  7.1 Minimum requirements for machine markings
  7.2 Instruction handbook
Annex A (informative) Classification of zones for printing presses and
        finishing machines (relating to 5.2.4)
      A.1 General
      A.2 Rotary web gravure printing machines
      A.3 Sheet-fed rotary gravure printing machines
      A.4 Rotary web flexographic printing machines, wallpaper
           printing machines
      A.5 Screen printing machines for printing on sheets, web or
           three-dimensional objects
      A.6 Rotary and flatbed film printing machines
      A.7 Machines for printing imitation leather and film
      A.8 Wash-out machines and washing machines in which flammable
           liquids with flash points below 55 degrees C used
      A.9 Roller coating units with closed side frames reaching down
           to floor level
      A.10 Roller coaters with side frames with cut-outs or with
           side frames that do not reach to floor level
Annex B (normative) Audible prestart warning devices
      B.1 Application
      B.2 Control arrangement
      B.3 Timing chart
Annex C (informative) Risk analysis relating to the pitch angle of
        access stairs
Annex D (informative) Example of layout of an instruction handbook
      D.1 Information relating to the machine
      D.2 Information relating to safety
      D.3 Information relating to transport, handling and storage of
           the machine
      D.4 Installation, commissioning, removal
      D.5 Information relating to the use of the machine
      D.6 Information relating to maintenance of the machine
Annex ZA (informative) Relationship between this European Standard
         and the Essential Requirements of EU Directive 98/37/EC
Annex ZB (informative) Clauses of this European Standard addressing
         essential requirements or other provisions of EU Directive
         94/9/EC
Bibliography

Applicable to printing machines for printing on paper and similar materials, including screen printing presses; equipment used in the preparation of the printing process and additional equipment on printing machines are also considered to be printing machines.

Committee
TC 198
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded

Standards Relationship
03/119040 DC : DRAFT NOV 2003 Identical

03/301332 DC : DRAFT JAN 2003 ISO 12649 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR BINDING AND FINISHING SYSTEMS AND EQUIPMENT
04/30110212 DC : DRAFT MAR 2004 ISO 12648 - GRAPHIC TECHNOLOGY - SAFETY REQUIREMENTS FOR PRINTING PRESS SYSTEMS
03/111188 DC : DRAFT AUG 2003 BS EN 1010-4 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - BOOKBINDING, PAPER CONVERTING AND FINISHING MACHINES
ISO 12649:2004 Graphic technology Safety requirements for binding and finishing systems and equipment
BS ISO 12649:2004 Graphic technology. Safety requirements for binding and finishing systems and equipment
05/19981969 DC : DRAFT JUN 2005 BS EN 1034-5 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 5: SHEETERS

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.