PREN 16191 : DRAFT 2010

Superseded View Superseded By

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

TUNNELLING MACHINERY - SAFETY REQUIREMENTS

Publisher: Comite Europeen de Normalisation

Published: 01-12-2013

Available Formats:
More Info on product formats

Pure ENs are not available for sale, please purchase a suitable national adoption

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
5 Safety requirements and/or protective
  measures
6 Verification of the safety requirements
  and/or protective measures
7 Information for use
Annex A (informative) - Examples of tunneling
        machines
Annex B (normative) - Verification of safety
        requirements and/or protective measures
Annex C (normative) - Noise
Annex D (normative) - Minimum requirements
        for rescue chamber
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

Abstract - (Show below) - (Hide below)

Applies to tunnelling machinery used for the construction of tunnels, shafts and other underground excavations. This describes the essential safety requirements for the design, installation, maintenance, and information for use of such machinery, covering reasonably foreseeable misuse of such machinery in that compliance with the requirements of clause 5 mitigates the risk arising from such misuse and monitoring for hazardous atmospheres within the confines of the tunneling machinery.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Draft
Status	Superseded
Publisher	Comite Europeen de Normalisation
Pages
ISBN
Committee	TC 151
Superseded By	EN 16191 : 2014
Comment Closes On

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
NF EN 16191 : 2014	Identical
10/30233953 DC : 0	Identical
NEN EN 16191 : 2014	Identical
10/30233953 DC : 0	Identical

Standards Referenced By This Book - (Show below) - (Hide below)

UNE EN 16228-1 : 2015	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
BS EN 16228-1 : 2014	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
UNI EN 16228-1 : 2014	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
DIN EN 16228-1 : 2014	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
DIN EN 16228-1 E : 2014	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
I.S. EN 16228-1:2014	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS
UNE EN 16228-1 : 2015	DRILLING AND FOUNDATION EQUIPMENT - SAFETY - PART 1: COMMON REQUIREMENTS

Standards Referencing This Book - (Show below) - (Hide below)

ISO 3449 : 2005(R2017)	EARTH MOVING MACHINERY - FALLING-OBJECT PROTECTIVE STRUCTURES - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS
EN ISO 2860 : 2008	EARTH-MOVING MACHINERY - MINIMUM ACCESS DIMENSIONS
ISO 11202 : 2010(R2015)	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
EN 894-3 : 2000 + A1 2008	SAFETY OF MACHINERY - ERGONOMICS REQUIREMENTS FOR THE DESIGN OF DISPLAYS AND CONTROL ACTUATORS - PART 3: CONTROL ACTUATORS
EN 982 : 96 + A1 2008	SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - HYDRAULICS
ISO 4871 : 1996(R2013)	ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT
EN 620 : 2002 + A1 2010
ISO 14122-3 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 3: STAIRS, STEPLADDERS AND GUARD-RAILS
EN 12110 : 2014	TUNNELLING MACHINES - AIR LOCKS - SAFETY REQUIREMENTS
ISO 14122-1 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 1: CHOICE OF FIXED MEANS AND GENERAL REQUIREMENTS OF ACCESS
EN 60825-1 : 2014 COR 2017	SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS (IEC 60825-1:2014)
EN 1088 : 1995 + A2 2008	SAFETY OF MACHINERY - INTERLOCKING DEVICES ASSOCIATED WITH GUARDS - PRINCIPLES FOR DESIGN AND SELECTION
EN 981 : 1996 + A1 2008	SAFETY OF MACHINERY - SYSTEM OF AUDITORY AND VISUAL DANGER AND INFORMATION SIGNALS
ISO TR 11688-1 : 1995(R2009)	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING
ISO 7096 : 2000	EARTH MOVING MACHINERY - LABORATORY EVALUATION OF OPERATOR SEAT VIBRATION
ISO 3411 : 2007	EARTH-MOVING MACHINERY - PHYSICAL DIMENSIONS OF OPERATORS AND MINIMUM OPERATOR SPACE ENVELOPE
EN 60079-0 : 2012 AMD 11 2013	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
EN ISO 3449 : 2008	EARTH-MOVING MACHINERY - FALLING-OBJECT PROTECTIVE STRUCTURES - LABORATORY TESTS AND PERFORMANCE REQUIREMENTS
EN ISO 3411 : 2007	EARTH-MOVING MACHINERY - PHYSICAL DIMENSIONS OF OPERATORS AND MINIMUM OPERATOR SPACE ENVELOPE
EN ISO 3457 : 2008	EARTH-MOVING MACHINERY - GUARDS - DEFINITIONS AND REQUIREMENTS (ISO 3457:2003)
ISO 13732-1 : 2006(R2010)	ERGONOMICS OF THE THERMAL ENVIRONMENT - METHODS FOR THE ASSESSMENT OF HUMAN RESPONSES TO CONTACT WITH SURFACES - PART 1: HOT SURFACES
ISO 12508 : 1994(R2015)	EARTH-MOVING MACHINERY - OPERATOR STATION AND MAINTENANCE AREAS - BLUNTNESS OF EDGES
EN 1837 : 1999 + A1 2009	SAFETY OF MACHINERY - INTEGRAL LIGHTING OF MACHINES
IEC 60439-2 : 3.1	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 2: PARTICULAR REQUIREMENTS FOR BUSBAR TRUNKING SYSTEMS (BUSWAYS)
EN 13478 : 2001 + A1 2008	SAFETY OF MACHINERY - FIRE PREVENTION AND PROTECTION
IEC 60204-1 : 6.0:2016	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS
EN ISO 13850 : 2015	SAFETY OF MACHINERY - EMERGENCY STOP FUNCTION - PRINCIPLES FOR DESIGN (ISO 13850:2015)
EN 1005-2 : 2003 + A1 2008	SAFETY OF MACHINERY - HUMAN PHYSICAL PERFORMANCE - PART 2: MANUAL HANDLING OF MACHINERY AND COMPONENT PARTS OF MACHINERY
IEC 60204-11 : 1.0	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
IEC 60825-1 : 3.0	SAFETY OF LASER PRODUCTS - PART 1: EQUIPMENT CLASSIFICATION AND REQUIREMENTS
IEC 60204-32 : 2.0	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
EN 60439-3 : 91 COR 3 2009	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 3: PARTICULAR REQUIREMENTS FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES INTENDED TO BE INSTALLED IN PLACES WHERE UNSKILLED PERSONS HAVE ACCESS FOR THEIR USE - DISTRIBUTION BOARDS
EN ISO 11688-2 : 2000	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
ISO 14122-4 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 4: FIXED LADDERS
EN 60947-1 : 2007 AMD 2 2014	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES (IEC 60947-1:2007/A2:2014)
ISO 3795 : 1989(R2019)	ROAD VEHICLES AND TRACTORS AND MACHINERY FOR AGRICULTURE AND FORESTRY - DETERMINATION OF BURNING BEHAVIOUR OF INTERIOR MATERIALS
EN ISO 13732-1 : 2008	ERGONOMICS OF THE THERMAL ENVIRONMENT - METHODS FOR THE ASSESSMENT OF HUMAN RESPONSES TO CONTACT WITH SURFACES - PART 1: HOT SURFACES
EN 60204-32 : 2008	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 32: REQUIREMENTS FOR HOISTING MACHINES
EN 60947-3 : 2009 AMD 2 2015	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS (IEC 60947-3:2008/A2:2015)
ISO 2860 : 1992(R2018)	EARTH-MOVING MACHINERY - MINIMUM ACCESS DIMENSIONS
EN 60439-4 : 2004	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 4: PARTICULAR REQUIREMENTS FOR ASSEMBLIES FOR CONSTRUCTION SITES (ACS)
EN ISO 12100-1 : 2003 AMD 1 2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN ISO 14122-3 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 3: STAIRS, STEPLADDERS AND GUARD-RAILS (ISO 14122-3:2016)
EN 3-7 : 2004 + A1 2007	PORTABLE FIRE EXTINGUISHERS - PART 7: CHARACTERISTICS, PERFORMANCE REQUIREMENTS AND TEST METHODS
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE)
EN 953 : 1997 + A1 2009	SAFETY OF MACHINERY - GUARDS - GENERAL REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF FIXED AND MOVABLE GUARDS
EN 13309 : 2010	CONSTRUCTION MACHINERY - ELECTROMAGNETIC COMPATIBILITY OF MACHINES WITH INTERNAL POWER SUPPLY
IEC 60947-1 : 5.2	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 1: GENERAL RULES
EN ISO 14122-4 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 4: FIXED LADDERS (ISO 14122-4:2016)
ISO 6405-1 : 2017	EARTH-MOVING MACHINERY - SYMBOLS FOR OPERATOR CONTROLS AND OTHER DISPLAYS - PART 1: COMMON SYMBOLS
IEC 60439-1 : 4.1	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1: TYPE-TESTED AND PARTIALLY TYPE-TESTED ASSEMBLIES
EN ISO 14122-2 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 2: WORKING PLATFORMS AND WALKWAYS (ISO 14122-2:2016)
IEC 60079-0 : 6.0	EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS
ISO 3457 : 2003(R2014)	EARTH-MOVING MACHINERY - GUARDS - DEFINITIONS AND REQUIREMENTS
ISO 12100-2 : 2003	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
EN ISO 12100-2 : 2003 AMD 1 2009	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 2: TECHNICAL PRINCIPLES
EN 60439-1 : 99 AMD 1 2004	LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 1 - TYPE TESTED AND PARTIALLY TYPE TESTED ASSEMBLIES
ISO 3864-1 : 2011(R2016)	GRAPHICAL SYMBOLS - SAFETY COLOURS AND SAFETY SIGNS - PART 1: DESIGN PRINCIPLES FOR SAFETY SIGNS AND SAFETY MARKINGS
EN 60204-11 : 2000 COR 2010	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 11: REQUIREMENTS FOR HV EQUIPMENT FOR VOLTAGES ABOVE 1000 V A.C. OR 1500 V D.C. AND NOT EXCEEDING 36 KV
EN 983 : 1996 + A1 2008	SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR FLUID POWER SYSTEMS AND THEIR COMPONENTS - PNEUMATICS
ISO 12100-1 : 2003	SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN ISO 13849-1 : 2015	SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN (ISO 13849-1:2015)
ISO 13850 : 2015	SAFETY OF MACHINERY - EMERGENCY STOP FUNCTION - PRINCIPLES FOR DESIGN
EN ISO 4871 : 2009	ACOUSTICS - DECLARATION AND VERIFICATION OF NOISE EMISSION VALUES OF MACHINERY AND EQUIPMENT
IEC 61310-1 : 2.0	SAFETY OF MACHINERY - INDICATION, MARKING AND ACTUATION - PART 1: REQUIREMENTS FOR VISUAL, ACOUSTIC AND TACTILE SIGNALS
IEC 60947-3 : 3.2	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 3: SWITCHES, DISCONNECTORS, SWITCH-DISCONNECTORS AND FUSE-COMBINATION UNITS
IEC 60947-2 : 2016	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 2: CIRCUIT-BREAKERS
EN 60529 : 1991 COR 2016	DEGREES OF PROTECTION PROVIDED BY ENCLOSURES (IP CODE) (IEC 60529 EDITION 2.2 CORRIGENDUM 2:2015)
EN 60947-2 : 2017	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 2: CIRCUIT-BREAKERS (IEC 60947-2:2016 + COR1:2016)
ISO 14122-2 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 2: WORKING PLATFORMS AND WALKWAYS
EN ISO 11688-1 : 2009	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 1: PLANNING (ISO/TR 11688-1:1995)
EN ISO 14122-1 : 2016	SAFETY OF MACHINERY - PERMANENT MEANS OF ACCESS TO MACHINERY - PART 1: CHOICE OF FIXED MEANS AND GENERAL REQUIREMENTS OF ACCESS (ISO 14122-1:2016)
ISO 13849-1 : 2015	SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 1: GENERAL PRINCIPLES FOR DESIGN
ISO TR 11688-2 : 1998(R2009)	ACOUSTICS - RECOMMENDED PRACTICE FOR THE DESIGN OF LOW-NOISE MACHINERY AND EQUIPMENT - PART 2: INTRODUCTION TO THE PHYSICS OF LOW-NOISE DESIGN
EN 61310-1 : 2008	SAFETY OF MACHINERY - INDICATION, MARKING AND ACTUATION - PART 1: REQUIREMENTS FOR VISUAL, ACOUSTIC AND TACTILE SIGNALS
IEC 60439-3 : 1.2	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 3: PARTICULAR REQUIREMENTS FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES INTENDED TO BE INSTALLED IN PLACES WHERE UNSKILLED PERSONS HAVE ACCESS FOR THEIR USE - DISTRIBUTION BOARDS
EN ISO 11202 : 2010	ACOUSTICS - NOISE EMITTED BY MACHINERY AND EQUIPMENT - DETERMINATION OF EMISSION SOUND PRESSURE LEVELS AT A WORK STATION AND AT OTHER SPECIFIED POSITIONS APPLYING APPROXIMATE ENVIRONMENTAL CORRECTIONS
IEC 60439-4 : 2.0	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 4: PARTICULAR REQUIREMENTS FOR ASSEMBLIES FOR CONSTRUCTION SITES (ACS)
EN 60439-2 : 2000 AMD 1 2005	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES - PART 2: PARTICULAR REQUIREMENTS FOR BUSBAR TRUNKING SYSTEMS (BUSWAYS)
EN ISO 7096 : 2008 COR 2009	EARTH-MOVING MACHINERY - LABORATORY EVALUATION OF OPERATOR SEAT VIBRATION
EN 60204-1 : 2006 COR 2010	SAFETY OF MACHINERY - ELECTRICAL EQUIPMENT OF MACHINES - PART 1: GENERAL REQUIREMENTS

Sorry this product is not available in your region.

PREN 16191 : DRAFT 2010

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

National Adoptions - (Show below) - (Hide below)

Standards Referenced By This Book - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?