• There are no items in your cart

PREN ISO 13849-2 : DRAFT 2010

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SAFETY OF MACHINERY - SAFETY-RELATED PARTS OF CONTROL SYSTEMS - PART 2: VALIDATION
Superseded date

10-01-2012

Published date

01-12-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Validation process
5 Validation by analysis
6 Validation by testing
7 Validation of safety requirements specification
8 Validation of safety functions
9 Validation of performance levels and categories
10 Validation of environmental requirements
11 Validation of maintenance requirements
12 Validation of technical documentation and information
   for use
Annex A (informative) - Validation tools for mechanical
        systems
Annex B (informative) - Validation tools for pneumatic
        systems
Annex C (informative) - Validation tools for hydraulic
        systems
Annex D (informative) - Validation tools for electrical
        systems
Annex E (informative) - Example of the validation of
        fault behaviour and diagnostic means
Bibliography

Describes the procedures and conditions to be followed for the validation by analysis and testing of: - the safety functions provided; - the category achieved; and - the performance level achieved, of the safety-related parts of the control system (SRP/CS) in compliance with ISO 13849-1, using the design rationale provided by the designer.

Committee
TC 114
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
10/30198892 DC : 0 Identical

IEC 61025:2006 Fault tree analysis (FTA)
ISO 14119:2013 Safety of machinery Interlocking devices associated with guards Principles for design and selection
ISO 4960:2007 Cold-reduced carbon steel strip with a mass fraction of carbon over 0,25 %
ISO 11161:2007 Safety of machinery — Integrated manufacturing systems — Basic requirements
EN 50205:2002 Relays with forcibly guided (mechanically linked) contacts
ISO 5598:2008 Fluid power systems and components Vocabulary
IEC 60812:2006 Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA)
IEC 60204-1:2016 Safety of machinery - Electrical equipment of machines - Part 1: General requirements
IEC 61078:2016 Reliability block diagrams
ISO 14118:2000 Safety of machinery Prevention of unexpected start-up
ISO 13851:2002 Safety of machinery Two-hand control devices Functional aspects and design principles
IEC 61165:2006 Application of Markov techniques
IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV Low-voltage fuses - Part 1: General requirements
EN 952:1999 Door leaves - General and local flatness - Measurement method
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV Degrees of protection provided by enclosures (IP Code)
EN 953:1997+A1:2009 Safety of machinery - Guards - General requirements for the design and construction of fixed and movable guards
ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 13850:2015 Safety of machinery Emergency stop function Principles for design
ISO 13849-1:2015 Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.