SAE AMS 3058 : 2013

Superseded

View Superseded by

GREASE: WIDE TEMPERATURE RANGE LITHIUM OR LITHIUM COMPLEX THICKENED FOR AIRCRAFT WHEEL BEARINGS

Available format(s)

Hardcopy , PDF

Superseded date

08-09-2018

Language(s)

English

Published date

03-28-2013

Publisher

SAE International

1. SCOPE
2. APPLICABLE DOCUMENTS
3. TECHNICAL REQUIREMENTS
4. QUALIFICATION
5. QUALITY ASSURANCE PROVISIONS
6. PREPARATION FOR DELIVERY
7. ACKNOWLEDGMENT
8. REJECTIONS
9. NOTES
APPENDIX A

Specifies grease for use on aircraft wheel bearings.

Committee	AMS-M
DocumentType	Standard
Pages	8
PublisherName	SAE International
Status	Superseded
SupersededBy	SAE AMS 3058A : 2018
Supersedes	SAE AMS 3058 : 2008

IP 71 : 1995	SECTION 1: PETROLEUM PRODUCTS - TRANSPARENT AND OPAQUE LIQUIDS - DETERMINATION OF KINEMATIC VISCOSITY AND CALCULATION OF DYNAMIC VISCOSITY - SECTION 2: GLASS CAPILLARY KINEMATIC VISCOMETERS - SPECIFICATIONS AND OPERATING INSTRUCTIONS (TWO PART SET)
ASTM D 566 : 2017 : REDLINE	Standard Test Method for Dropping Point of Lubricating Grease
DEFSTAN 05-50(PT62)/1(1995) : 1995	METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 62: LOW TEMPERATURE TORQUE OF GREASES CONTAMINATED WITH WATER
ASTM D 5706 : 2016 : REDLINE	Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
IP 132 : 96(R2004)	PETROLEUM PRODUCTS - LUBRICATING GREASE - DETERMINATION OF DROPPING POINT
ASTM D 942 : 2015 : REDLINE	Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method
ISO 2160:1998	Petroleum products Corrosiveness to copper Copper strip test
ASTM D 6184 : 2017 : REDLINE	Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method)
DEFSTAN 05-50(PT9)/1(1986) : 1986	METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 9: SEPARATION OF OIL FROM GREASE
SAE AMS 4640 : 2011	ALUMINUM BRONZE, BARS, RODS, SHAPES, TUBES, AND FORGINGS, 81.5CU - 10.0AL - 4.8NI - 3.0FE, DRAWN AND STRESS RELIEVED (HR50) OR TEMPER ANNEALED (TQ50)
ASTM D 5707 : 2016 : REDLINE	Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
ASTM D 217 : 2017 : REDLINE	TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE
ASTM D 4048 : 2017-01	TEST METHOD FOR DETECTION OF COPPER CORROSION FROM LUBRICATING GREASE
ASTM D 4289 : 2014-02	TEST METHOD FOR ELASTOMER COMPATIBILITY OF LUBRICATING GREASES AND FLUIDS
SAE AMS 3217/2 : 2012	TEST SLABS, ACRYLONITRILE BUTADIENE (NBR-L), LOW ACRYLONITRILE, 65-75
ASTM D 2595 : 2017	Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
FED-STD-791 Revision D:2007	TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS
ISO 2176:1995	Petroleum products — Lubricating grease — Determination of dropping point
ASTM D 2265 : 2015-05	TEST METHOD FOR DROPPING POINT OF LUBRICATING GREASE OVER WIDE TEMPERATURE RANGE