SAE AS 4444 : 2013
Current
Current
The latest, up-to-date edition.
FITTINGS, 24 DEGREE CONE FLARELESS, FLUID CONNECTION, 5000 PSI
Available format(s)
Hardcopy , PDF
Language(s)
English
Published date
01-07-2013
Publisher
1 SCOPE
2 REFERENCES
3 TECHNICAL REQUIREMENTS
4 QUALITY ASSURANCE PROVISIONS
5 PREPARATION FOR DELIVERY
6 NOTES
Establishes the requirements for 24 degree cone flareless fluid connection fittings and nuts and bite type flareless sleeves for use in aircraft fluid systems at an operating pressure of 5000 psi for the fittings and nuts and 3000 psi for the bite type sleeves.
| Committee |
G-3
|
| DocumentType |
Standard
|
| Pages |
27
|
| PublisherName |
SAE International
|
| Status |
Current
|
| Supersedes |
| SAE AS 4510/1 : 1996 | FITTINGS, WELD TO 24 DEGREE CONE FLARELESS, FLUID CONNECTION |
| SAE AIR 5426 : 2013 | FITTING AND FITTING ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE OF |
| SAE AS932C:2023 | FITTING, ADAPTER, REDUCER/EXPANDER, FLARELESS TO BOSS |
| SAE AS 18280 : 2017 | FITTINGS, 24 DEGREES CONE FLARELESS, FLUID CONNECTION, 3000 PSI |
| SAE AS 5620 : 2017 | TITANIUM HYDRAULIC TUBING, TI-3AL-2.5V COLD WORKED AND STRESS RELIEVED, UP TO 35000 KPA (5080 PSI), REQUIREMENTS FOR QUALIFICATION TESTING AND CONTROL |
| SAE AS 4444/2 : 2015 | Fitting, 24° Cone Flareless to 37° Flared, Fluid Connection |
| SAE AMS 2486 : 2010 | CONVERSION COATING OF TITANIUM ALLOYS FLUORIDE-PHOSPHATE TYPE |
| QQ-A-225-9 Revision E:1982 | ALUMINUM ALLOY BAR, ROD, WIRE, AND SPECIAL SHAPES, ROLLED, DRAWN, OR COLD FINISHED, 7075 |
| SAE AMS5659S : 2016 | Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu<br> |
| SAE AMS 5645 : 2016 | STEEL, CORROSION AND HEAT RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 18CR - 10NI - 0.40TI (321), SOLUTION HEAT TREATED |
| SAE ARP 603 : 1985 | IMPULSE TESTING OF HYDRAULIC HOSE, TUBING, AND FITTING ASSEMBLIES |
| MS 21932 : 0 | FITTING END BOLT CLUSTER FITTING SINGLE PORT (ASG) |
| MIL H 46170 : B | HYDRAULIC FLUID, RUST INHIBITED, FIRE-RESISTANT, SYNTHETIC HYDROCARBON BASE |
| SAE AS 4703 : 2015 | FITTING END, ACORN, SHORT FLARELESS, DESIGN STANDARD |
| QQ-P-35 Revision C:1988 | PASSIVATION TREATMENTS FOR CORROSION-RESISTANT STEEL |
| SAE AMS 2488 : 2000 | ANODIC TREATMENT - TITANIUM AND TITANIUM ALLOYS SOLUTION PH 13 OR HIGHER |
| MIL-F-18280 Revision F:1995 | FITTING, FLARELESS TUBE, FLUID CONNECTION |
| MIL-T-6845 Revision D:1985 | TUBING, STEEL, CORROSION-RESISTANT (304) AEROSPACE VEHICLE HYDRAULIC SYSTEM 1/8 HARD CONDITION |
| NAS1760:2015 | FITTING END, FLARELESS ACORN, STANDARD DIMENSIONS FOR |
| SAE AMS 2770 : 2015 | HEAT TREATMENT OF WROUGHT ALUMINUM ALLOY PARTS |
| MIL-H-6875 Revision H:1989 | HEAT TREATMENT OF STEEL RAW MATERIALS |
| MS21934 Base Document:1987 | FITTING END BOLT CLUSTER FITTING DOUBLE PORT (ASG) |
| SAE ARP 1185 : 2013 | FLEXURE TESTING OF HYDRAULIC TUBING JOINTS AND FITTINGS |
| SAE AMS 4112 : 1996 | BARS, RODS, AND WIRE, ROLLED, DRAWN, OR COLD FINISHED - 4.4Cu 1.5Mg 0.60Mn |
| SAE AMS 4141 : 2014 | ALUMINUM ALLOY DIE FORGINGS, 5.6ZN - 2.5MG - 1.6CU - 0.23CR (7075-T73), SOLUTION AND PRECIPITATION HEAT TREATED |
| MIL-STD-1655 Base Document:1975 | FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF |
| QQ-A-367 Revision H:1973 | ALUMINUM ALLOY FORGINGS |
| SAE AMS 2759 : 2014 | HEAT TREATMENT OF STEEL PARTS, GENERAL REQUIREMENTS |
| MS33515 Revision J:1973 | FITTING END, STANDARD DIMENSIONS FOR BULKHEAD FLARELESS TUBE CONNECTIONS |
| ASME B46.1 : 2009 | SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY) |
| SAE AS 4658 : 2013 | FITTING END, EXTERNAL THREAD, SHORT FLARELESS, DESIGN STANDARD |
| SAE AMS 5648 : 2016 | STEEL, CORROSION AND HEAT-RESISTANT, BARS, WIRE, FORGINGS, TUBING, AND RINGS, 17CR - 12NI - 2.5MO (316), SOLUTION HEAT TREATED |
| SAE AMS 4134 : 2012 | ALUMINUM ALLOY, DIE FORGINGS, 4.4CU - 0.85SI - 0.80MN - 0.50MG (2014-T4), SOLUTION HEAT TREATED |
| SAE ARP 891 : 1976 | DETERMINATION OF ALUMINUM ALLOY TEMPERS THROUGH ELECTRICAL CONDUCTIVITY MEASUREMENT (EDDY CURRENT) |
| QQ A 225/6 : E | ALUMINUM ALLOY BAR, ROD, AND WIRE, ROLLED, DRAWN OR COLD FINISHED, 2024 |
| MIL H 83282 : C | HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, AIRCRAFT, METRIC, NATO CODE NUMBER H 537 |
| MIL H 6083 : E | HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION |
| MIL-STD-12 Revision D:1981 | ABBREVIATIONS FOR USE ON DRAWINGS, SPECIFICATIONS FOR STANDARDS AND IN TECHNICAL DOCUMENTS |
| SAE AS 1376 : 2013 | ALTERNATE DIMENSIONS, CENTER BODY SECTION, SHAPE FLUID FITTING, DESIGN STANDARD |
| MIL-S-8879 Revision C:1991 | SCREW THREADS, CONTROLLED RADIUS ROOT WITH INCREASED MINOR DIAMETER, GENERAL SPECIFICATION FOR |
| MIL A 8625 : F | ANODIC COATINGS FOR ALUMINUM AND ALUMINUM ALLOYS |
| QQ-S-763 Revision F:1996 | STEEL BARS, WIRE, SHAPES AND FORGINGS; CORROSION RESISTANT |
| SAE AS 4444/1 : 2013 | SLEEVE, BITE TYPE, 24 DEGREE CONE FLARELESS FITTING |
| SAE AS 1241 : 2016 | FIRE RESISTANT PHOSPHATE ESTER HYDRAULIC FLUID FOR AIRCRAFT |
| SAE AS 4458 : 2015 | FITTING END, FLARELESS BLUNT NOSE, DESIGN STANDARD |
| SAE AMS 5639 : 2017 | STEEL, CORROSION-RESISTANT, BARS, WIRE, FORGINGS, MECHANICAL TUBING, AND RINGS, 19CR - 10NI, SOLUTION HEAT TREATED |
| MIL-S-6758 Revision B:1993 | STEEL, CHROME-MOLYBDENUM (4130) BARS AND REFORGING STOCK (AIRCRAFT QUALITY) |
| MIL-H-6088 Revision G:1991 | HEAT TREATMENT OF ALUMINIUM ALLOYS |
| MIL H 5606 : G | HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE |
| SAE AMS 6370 : 2016 | STEEL, BARS, FORGINGS, AND RINGS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130) |
| SAE AS 4375 : 2013 | FITTING END, FLARELESS, DESIGN STANDARD |
| QQ-P-416 Revision F:1991 | PLATING, CADMIUM (ELECTRODEPOSITED) |
| SAE AS 4659 : 2013 | FITTING END, BULKHEAD, EXTERNAL THREAD, SHORT FLARELESS, DESIGN STANDARD |
| SAE ARP 4784 : 2013 | DEFINITIONS AND LIMITS, METAL MATERIAL DEFECTS AND SURFACE AND EDGE FEATURES, FLUID COUPLINGS, FITTINGS AND HOSE ENDS |
| MS33514 Revision G:1990 | FITTING END, STANDARD DIMENSIONS FOR FLARELESS TUBE CONNECTION AND GASKET SEAL (ASG) |
| MIL L 46010 : D | LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING |
| ISO 10012-1:1992 | Quality assurance requirements for measuring equipment Part 1: Metrological confirmation system for measuring equipment |
| FED-STD-595 Revision C:2008 | COLORS USED IN GOVERNMENT PROCUREMENT |
| SAE AMS 4124 : 2012 | ALUMINUM ALLOY, ROLLED OR COLD FINISHED BARS, RODS, AND WIRE - 5.6ZN - 2.5MG - 1.6CU - 0.23CR (7075-T7351), SOLUTION HEAT TREATED, STRESS RELIEVED BY STRETCHING, AND OVERAGED |
| SAE AMS 4928 : 2016 | TITANIUM ALLOY BARS, WIRE, FORGINGS, RINGS, AND DRAWN SHAPES, 6AL - 4V, ANNEALED |
| SAE AS 4377 : 2013 | FITTING END, BULKHEAD, FLARELESS, DESIGN STANDARD |
US$148.68
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.