• There are no items in your cart

S.R. CEN ISO TS 24817:2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - COMPOSITE REPAIRS FOR PIPEWORK - QUALIFICATION AND DESIGN, INSTALLATION, TESTING AND INSPECTION
Available format(s)

Hardcopy , PDF

Superseded date

08-22-2015

Language(s)

English

Published date

01-01-2011

Preview

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Applications
6 Qualification and design
7 Installation
8 Testing and inspection
9 System testing
10 Future modifications
11 Decommissioning
Annex A (normative) - Design data sheet
Annex B (normative) - Qualification data
Annex C (normative) - Short-term pipe spool survival test
Annex D (normative) - Measurement of [gamma]LCL for through-wall
        defect calculation
Annex E (normative) - Measurement of performance test data
Annex F (normative) - Measurement of impact performance
Annex G (normative) - Measurement of the degradation factor
Annex H (informative) - Axial extent of repair look-up table
Annex I (normative) - Installer qualification
Annex J (normative) - Installation requirements and guidance
Bibliography

Provides requirements and recommendations for the qualification and design, installation, testing and inspection for the external application of composite repairs to corroded or damaged pipework used in the petroleum, petrochemical and natural gas industries.

DocumentType
Standard
Pages
83
PublisherName
National Standards Authority of Ireland
Status
Superseded
SupersededBy

Standards Relationship
CEN ISO/TS 24817:2011 Identical
ISO/TS 24817:2006 Identical

ISO 15649:2001 Petroleum and natural gas industries — Piping
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ASTM G 8 : 1996 Standard Test Methods for Cathodic Disbonding of Pipeline Coatings
EN 59:2016 Glass reinforced plastics - Determination of indentation hardness by means of a Barcol hardness tester
ANSI/AWWA C200 : 2017 STEEL WATER PIPE, 6 IN. (150 MM) AND LARGER
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ISO 15310:1999 Fibre-reinforced plastic composites Determination of the in-plane shear modulus by the plate twist method
AWWA C151/A21.51 : 2017 DUCTILE-IRON PIPE, CENTRIFUGALLY CAST
ISO 11359-2:1999 Plastics Thermomechanical analysis (TMA) Part 2: Determination of coefficient of linear thermal expansion and glass transition temperature
AWWA C150/A21.50 : 2014 THICKNESS DESIGN OF DUCTILE-IRON PIPE
ASTM D 5379/D5379M : 2012 : REDLINE Standard Test Method for Shear Properties of Composite Materials by the V-Notched Beam Method
AWWA M11 : 2004 STEEL PIPE: A GUIDE FOR DESIGN AND INSTALLATION
ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ASTM C 581 : 2015 : REDLINE Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service
ASTM D 696 : 2016 : REDLINE Standard Test Method for Coefficient of Linear Thermal Expansion of Plastics Between −30°C and 30°C with a Vitreous Silica Dilatometer
ASTM D 790 : 2017 : REDLINE Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
API 579-1 : 2016 FITNESS-FOR-SERVICE
ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ASTM D 2992 : 2012 Standard Practice for Obtaining Hydrostatic or Pressure Design Basis for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Fittings
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
EN 1465:2009 Adhesives - Determination of tensile lap-shear strength of bonded assemblies
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 14129:1997 Fibre-reinforced plastic composites — Determination of the in-plane shear stress/shear strain response, including the in-plane shear modulus and strength, by the plus or minus 45 degree tension test method

View more information
US$114.01
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.