• There are no items in your cart

UNI EN 14364 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PLASTICS PIPING SYSTEMS FOR DRAINAGE AND SEWERAGE WITH OR WITHOUT PRESSURE - GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) BASED ON UNSATURATED POLYESTER RESIN (UP) - SPECIFICATIONS FOR PIPES, FITTINGS AND JOINTS
Superseded date

10-06-2021

Published date

01-01-2013

Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 General requirements
5 Pipes
6 Fittings
7 Joint performance
Annex A (normative) - Test method for the resistance
        to bending and pressure of end-thrust loaded
        joints in pipe systems
Bibliography

Describes the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for drainage or sewerage, including culverts, with or without pressure.

DevelopmentNote
Supersedes UNI EN 1115-1, UNI EN 1115-3, UNI EN 1115-5, UNI EN 1636-3 and UNI EN 1636-5. (07/2008)
DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
EN 14364:2013 Identical

UNI 9032 : 2008 GLASS-REINFORCED THERMOSETTING PLASTICS (GRP) PIPING WITH OR WITHOUT FILLERS - GUIDANCE TO THE DEFINITION OF THE REQUIREMENTS FOR THE USE

ISO 8521:2009 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
ISO 7432:2002 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
EN ISO 2078:1994/A1:2015 TEXTILE GLASS - YARNS - DESIGNATION (ISO 2078:1993/AMD 1:2015)
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 527-4:1997 Plastics Determination of tensile properties Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
ISO 7685:1998 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of initial specific ring stiffness
EN ISO 527-4:1997 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 4: TEST CONDITIONS FOR ISOTROPIC AND ORTHOTROPIC FIBRE-REINFORCED PLASTIC COMPOSITES
ISO/TR 10465-3:2007 Underground installation of flexible glass-reinforced pipes based on unsaturated polyester resin (GRP-UP) Part 3: Installation parameters and application limits
ISO 10928:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
ISO 1452-3:2009 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure Unplasticized poly(vinyl chloride) (PVC-U) Part 3: Fittings
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
CEN/TS 14632:2012 Plastics piping systems for drainage, sewerage and water supply, pressure and non-pressure - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the assessment of conformity
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 527-5:2009 Plastics Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
EN 1447:2009+A1:2010 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) pipes - Determination of long-term resistance to internal pressure
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series
EN 476:2011 General requirements for components used in drains and sewers
ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin Test methods to prove the design of cemented or wrapped joints
ISO 2078:1993 Textile glass Yarns Designation
ISO 8483:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings Test methods to prove the design of bolted flange joints
ISO 8513:2016 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test methods for the determination of the initial longitudinal tensile strength
ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
ISO 4200:1991 Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length
ISO 10466:1997 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test method to prove the resistance to initial ring deflection
ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
EN ISO 527-5:2009 Plastics - Determination of tensile properties - Part 5: Test conditions for unidirectional fibre-reinforced plastic composites (ISO 527-5:2009)
EN 1119:2009 Plastics piping systems - Joints for glass-reinforced thermosetting plastics (GRP) pipes and fittings - Test methods for leaktightness and resistance to damage of non-thrust resistant flexible joints with elastomeric sealing elements
EN ISO 1452-3:2010 Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 3: Fittings (ISO 1452-3:2009, corrected version 2010-03-01)
ISO 10952:2014 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes and fittings Determination of the resistance to chemical attack for the inside of a section in a deflected condition
CEN/TS 14807:2013 Plastics piping systems - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Guidance for the structural analysis of buried GRP-UP pipelines
ISO 2531:2009 Ductile iron pipes, fittings, accessories and their joints for water applications
CEN/TS 14578:2013 Plastics piping systems for water supply or drainage and sewerage - Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) - Recommended practice for installation

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.