• There are no items in your cart

UNI EN ISO 23936-1 : 2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - NON-METALLIC MATERIALS IN CONTACT WITH MEDIA RELATED TO OIL AND GAS PRODUCTION - PART 1: THERMOPLASTICS
Superseded date

11-16-2022

Published date

10-08-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and abbreviated terms
  3.1 Terms and definitions
  3.2 Abbreviated terms
4 Functional requirements
  4.1 General
  4.2 Pipelines, piping and liners
  4.3 Seals, washers and gaskets
  4.4 Encapsulations, electrical insulations, injection lines
5 Requirements for technical information
6 Requirements for manufacturers
  6.1 General requirements
  6.2 Raw material manufacturer
  6.3 Component manufacturer
  6.4 Validity of qualification
7 Qualification of thermoplastic materials
  7.1 General
  7.2 Requirements for chemical resistance tests
Annex A (informative) - Typical chemical properties of
        commonly used thermoplastic materials in media
        encountered in oil and gas production
Annex B (normative) - Test media, conditions, equipment,
        procedures and test report requirements
Bibliography

Supplies general principles and provides requirements and recommendations for the selection and qualification, and provides guidance for the quality assurance, of non-metallic materials for service in equipment used in oil and gas production environments, where the failure of such equipment could pose a risk to the health and safety of the public and personnel or to the environment.

Committee
CT 700
DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy

Standards Relationship
ISO 23936-1:2009 Identical
EN ISO 23936-1:2009 Identical

ISO 2578:1993 Plastics Determination of time-temperature limits after prolonged exposure to heat
NACE TM 01 87 : 2011 EVALUATING ELASTOMERIC MATERIALS IN SOUR GAS ENVIRONMENTS
ISO/TS 29001:2010 Petroleum, petrochemical and natural gas industries Sector-specific quality management systems Requirements for product and service supply organizations
ISO 1874-1:2010 Plastics Polyamide (PA) moulding and extrusion materials Part 1: Designation system and basis for specification
ISO 13628-1:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 1: General requirements and recommendations
ISO 13628-2:2006 Petroleum and natural gas industries Design and operation of subsea production systems Part 2: Unbonded flexible pipe systems for subsea and marine applications
ISO 1873-2:2007 Plastics Polypropylene (PP) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 13628-9:2000 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 9: Remotely Operated Tool (ROT) intervention systems
API TR 17TR2 : 2003 THE AGEING OF PA-11 IN FLEXIBLE PIPES
ISO 13628-3:2000 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 3: Through flowline (TFL) systems
ISO 16770:2004 Plastics Determination of environmental stress cracking (ESC) of polyethylene Full-notch creep test (FNCT)
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
ASTM D 3032 : 2016 : REDLINE Standard Test Methods for Hookup Wire Insulation
ISO 11357-5:2013 Plastics — Differential scanning calorimetry (DSC) — Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
ISO 14692-4:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 4: Fabrication, installation and operation
ISO 846:1997 Plastics Evaluation of the action of microorganisms
ISO 13628-11:2007 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 11: Flexible pipe systems for subsea and marine applications
API SPEC 17J : 2014 SPECIFICATION FOR UNBONDED FLEXIBLE PIPE
ISO 11357-3:2011 Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallization
ISO 1874-2:2012 Plastics Polyamide (PA) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 11357-2:2013 Plastics Differential scanning calorimetry (DSC) Part 2: Determination of glass transition temperature and glass transition step height
ISO 11357-4:2014 Plastics Differential scanning calorimetry (DSC) Part 4: Determination of specific heat capacity
ISO 15156-2:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
ISO 15156-3:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
ISO 14692-1:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 1: Vocabulary, symbols, applications and materials
ISO 13628-7:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 7: Completion/workover riser systems
ISO 15750-3:2002 Packaging Steel drums Part 3: Inserted flange-type closure systems
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
EN 579:1993 Plastics piping systems - Crosslinked polyethylene (PE-X) pipes - Determination of degree of crosslinking by solvent extraction
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
ISO 14001:2015 Environmental management systems — Requirements with guidance for use
ISO 177:2016 Plastics Determination of migration of plasticizers
ISO 1872-2:2007 Plastics Polyethylene (PE) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties
ISO 176:2005 Plastics — Determination of loss of plasticizers — Activated carbon method
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
ISO 1183-3:1999 Plastics Methods for determining the density of non-cellular plastics Part 3: Gas pyknometer method
ISO 9001:2015 Quality management systems — Requirements
ISO 15156-1:2015 Petroleum and natural gas industries Materials for use in H2S-containing environments in oil and gas production Part 1: General principles for selection of cracking-resistant materials
ISO 13628-6:2006 Petroleum and natural gas industries Design and operation of subsea production systems Part 6: Subsea production control systems
ISO 179-1:2010 Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 13628-4:2010 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 4: Subsea wellhead and tree equipment
ISO 62:2008 Plastics Determination of water absorption
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 306:2013 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)
ISO 13628-8:2002 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 8: Remotely Operated Vehicle (ROV) interfaces on subsea production systems
ASTM D 695 : 2015 : REDLINE Standard Test Method for Compressive Properties of Rigid Plastics
ISO 13628-5:2009 Petroleum and natural gas industries Design and operation of subsea production systems Part 5: Subsea umbilicals
ISO 11357-1:2016 Plastics — Differential scanning calorimetry (DSC) — Part 1: General principles
ISO 178:2010 Plastics Determination of flexural properties
ISO 14692-3:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 3: System design
ASTM D 2990 : 2017 : REDLINE Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 13623:2017 Petroleum and natural gas industries — Pipeline transportation systems
ISO 868:2003 Plastics and ebonite — Determination of indentation hardness by means of a durometer (Shore hardness)
ASTM D 1693 : 2015 : REDLINE Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ISO 13628-10:2005 Petroleum and natural gas industries — Design and operation of subsea production systems — Part 10: Specification for bonded flexible pipe

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.